Home › Engine / Hybrid System · 1AZ-FE › ENGINE CONTROL › SFI SYSTEM

DTC    P0120    Throttle / Pedal Position Sensor / Switch "A" Circuit Malfunction

DTC    P0121    Throttle / Pedal Position Sensor / Switch "A" Circuit Range / Performance Problem

DTC    P0122    Throttle / Pedal Position Sensor / Switch "A" Circuit Low Input

DTC    P0123    Throttle / Pedal Position Sensor / Switch "A" Circuit High Input

DTC    P0220    Throttle / Pedal Position Sensor / Switch "B" Circuit

DTC    P0222    Throttle / Pedal Position Sensor / Switch "B" Circuit Low Input

DTC    P0223    Throttle / Pedal Position Sensor / Switch "B" Circuit High Input

DTC    P2135    Throttle / Pedal Position Sensor / Switch "A" / "B" Voltage Correlation

for Preparation Click here


DESCRIPTION

HINT:
These DTCs relate to the throttle position sensor.

The throttle position sensor is mounted on the throttle with motor body assembly, and detects the opening angle of the throttle valve. This sensor is a non-contact type sensor. It uses Hall-effect elements in order to yield accurate signals even in extreme driving conditions, such as at high speeds as well as very low speeds.
The throttle position sensor has 2 sensor circuits, VTA1 and VTA2 each of which transmits a signal. VTA1 is used to detect the throttle valve angle and VTA2 is used to detect malfunctions in VTA1. The sensor signal voltages vary between 0 V and 5 V in proportion to the throttle valve opening angle, and are transmitted to the VTA1 and VTA2 terminals of the ECM.
As the valve closes, the sensor output voltage decreases and as the valve opens, the sensor output voltage increases. The ECM calculates the throttle valve opening angle according to these signals and controls the throttle actuator in response to driver inputs. These signals are also used in calculations such as air fuel ratio correction, power increase correction and fuel-cut control.

A255773E06


DTC No.
DTC Detection Condition
Trouble Area
P0120
The output voltage of VTA1 quickly fluctuates beyond the lower and upper malfunction thresholds for 2 seconds or more (1 trip detection logic).
  1. Throttle position sensor (built into throttle with motor body assembly)
  2. ECM
P0121
The difference between the VTA1 and VTA2 voltages is less than 0.8 V, or higher than 1.6 V for 2 seconds (1 trip detection logic).
  1. Throttle position sensor (built into throttle with motor body assembly)
  2. Throttle position sensor circuit
  3. ECM
P0122
The output voltage of VTA1 is 0.2 V or less for 2 seconds or more (1 trip detection logic).
  1. Throttle position sensor (built into throttle with motor body assembly)
  2. Short in VTA1 circuit
  3. Open in VCTA circuit
  4. ECM
P0123
The output voltage of VTA1 is 4.54 V or higher for 2 seconds or more (1 trip detection logic).
  1. Throttle position sensor (built into throttle with motor body assembly)
  2. Open in VTA1 circuit
  3. Open in ETA circuit
  4. Short between VCTA and VTA1 circuits
  5. ECM
P0220
The output voltage of VTA2 quickly fluctuates beyond the lower and upper malfunction thresholds for 2 seconds or more (1 trip detection logic).
  1. Throttle position sensor (built into throttle with motor body assembly)
  2. ECM
P0222
The output voltage of VTA2 is 1.75 V or less for 2 seconds or more (1 trip detection logic).
  1. Throttle position sensor (built into throttle with motor body assembly)
  2. Short in VTA2 circuit
  3. Open in VCTA circuit
  4. ECM
P0223
The output voltage of VTA2 is 4.8 V or higher, and VTA1 is between 0.2 V and 2.02 V for 2 seconds or more (1 trip detection logic).
  1. Throttle position sensor (built into throttle with motor body assembly)
  2. Open in VTA2 circuit
  3. Open in ETA circuit
  4. Short between VCTA and VTA2 circuits
  5. ECM
P2135
Either of the following conditions is met (1 trip detection logic):
(a) The difference between the output voltages of VTA1 and VTA2 is 0.02 V or less for 0.5 seconds or more.
(b) The output voltage of VTA1 is 0.2 V or less, and VTA2 is 1.75 V or less for 0.4 seconds or more.
  1. Short between VTA1 and VTA2 circuits
  2. Throttle position sensor (built into throttle with motor body assembly)
  3. ECM

HINT:
  1. When any of these DTCs are output, check the throttle valve opening angle using the intelligent tester. Enter the following menus: Powertrain / Engine and ECT / Data List / All Data / Throttle Position No. 1 and Throttle Position No. 2.
  2. Throttle Position No. 1 is the VTA1 signal, and Throttle Position No. 2 is the VTA2 signal.

    Reference (Normal Condition):

    Tester Display
    Accelerator Pedal Fully Released
    Accelerator Pedal Fully Depressed
    Throttle Position No. 1
    0.5 to 1.1 V
    3.2 to 4.8 V
    Throttle Position No. 2
    2.1 to 3.1 V
    4.6 to 4.98 V


MONITOR DESCRIPTION

The ECM uses the throttle position sensor to monitor the throttle valve opening angle. There are several checks that the ECM performs to confirm the proper operation of the throttle position sensor.
P0120, P0122, P0123, P0220, P0222, P0223 and P2135:
  1. A specific voltage difference is expected between the sensor terminals, VTA1 and VTA2, for each throttle valve opening angle. If the difference between VTA1 and VTA2 is incorrect, the ECM interprets this as a malfunction in the sensor circuit, and stores a DTC.
  2. VTA1 and VTA2 each have a specific voltage range. If VTA1 or VTA2 is outside the normal operating range, the ECM interprets this as a malfunction in the sensor circuit, and stores a DTC.
  3. VTA1 and VTA2 should never be close to the same voltage level. If VTA1 is within 0.02 V of VTA2, the ECM determines that there is a short circuit in the sensor circuit, and stores a DTC.
P0121:
  1. This sensor transmits two signals: VTA1 and VTA2. VTA1 is used to detect the throttle opening angle and VTA2 is used to detect malfunctions in VTA1. The ECM performs several checks to confirm the proper operation of the throttle position sensor and VTA1.
    For each throttle opening angle, a specific voltage difference is expected between the outputs of VTA1 and VTA2. If the output voltage difference between the two signals deviates from the normal operating range, the ECM interprets this as a malfunction in the throttle position sensor. The ECM illuminates the MIL and stores the DTC.

MONITOR STRATEGY


Frequency of Operation
Continuous

CONFIRMATION DRIVING PATTERN


A198824E17

  1. Connect the intelligent tester to the DLC3.
  2. Turn the ignition switch to ON and turn the tester on.
  3. Clear the DTCs (even if no DTCs are stored, perform the clear DTC procedure).
  4. Turn the ignition switch off and wait for at least 30 seconds.
  5. Turn the ignition switch to ON and turn the tester on [A].
  6. Start the engine.
  7. With the vehicle stationary, fully depress and release the accelerator pedal [B].
  8. Idle the engine for 2 seconds or more [C].
  9. Enter the following menus: Powertrain / Engine and ECT / DTC [D].
  10. Read the pending DTCs.

    HINT:
    1. If a pending DTC is output, the system is malfunctioning.
    2. If a pending DTC is not output, perform the following procedure.

  11. Enter the following menus: Powertrain / Engine and ECT / Utility / All Readiness.
  12. Input the DTC: P0120, P0121, P0122, P0123, P0220, P0222, P0223 or P2135.
  13. Check the DTC judgment result.

    Tester Display
    Description
    NORMAL
    1. DTC judgment completed
    2. System normal
    ABNORMAL
    1. DTC judgment completed
    2. System abnormal
    INCOMPLETE
    1. DTC judgment not completed
    2. Perform driving pattern after confirming DTC enabling conditions
    N/A
    1. Unable to perform DTC judgment
    2. Number of DTCs which do not fulfill DTC preconditions has reached ECU memory limit

    HINT:
    1. If the judgment result shows NORMAL, the system is normal.
    2. If the judgment result shows ABNORMAL, the system has a malfunction.
    3. If the judgment result shows INCOMPLETE or N/A, perform steps [B] through [D] again.


FAIL-SAFE

When any of these DTCs or other DTCs relating to Electronic Throttle Control System (ETCS) malfunctions are stored, the ECM enters fail-safe mode. During fail-safe mode, the ECM cuts the current to the throttle actuator, and the throttle valve is returned to a 6.5° throttle angle by the return spring. The ECM then adjusts the engine output by controlling the fuel injection (intermittent fuel-cut) and ignition timing, in accordance with the accelerator pedal angle, to allow the vehicle to continue operating at a minimal speed. If the accelerator pedal is depressed firmly and gently, the vehicle can be driven slowly.
Fail-safe mode continues until a pass condition is detected, and the ignition switch is then turned off.

WIRING DIAGRAM


A255182E25


INSPECTION PROCEDURE

HINT:
Read freeze frame data using the intelligent tester. The ECM records vehicle and driving condition information as freeze frame data the moment a DTC is stored. When troubleshooting, freeze frame data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, if the air fuel ratio was lean or rich, and other data from the time the malfunction occurred.

1.READ VALUE USING INTELLIGENT TESTER (THROTTLE POSITION SENSOR)
  1. Connect the intelligent tester to the DLC3.

  1. Turn the ignition switch to ON.

  1. Turn the tester on.

  1. Enter the following menus: Powertrain / Engine and ECT / Data List / All Data / Throttle Position No. 1 and Throttle Position No. 2.

  1. Read the values displayed on the tester.

    Result 
    When Accelerator Pedal Fully Released
    When Accelerator Pedal Fully Depressed
    Trouble Area
    Proceed to
    Throttle Position No. 1
    (VTA1)
    Throttle Position No. 2
    (VTA2)
    Throttle Position No. 1
    (VTA1)
    Throttle Position No. 2
    (VTA2)
    0 to 0.2 V
    0 to 0.2 V
    0 to 0.2 V
    0 to 0.2 V
    VCTA circuit open
    A
    4.5 to 4.98 V
    4.5 to 4.98 V
    4.5 to 4.98 V
    4.5 to 4.98 V
    ETA circuit open
    0 to 0.2 V,
    or 4.5 to 4.98 V
    2.1 to 3.1 V
    (Fail-safe)
    0 to 0.2 V,
    or 4.5 to 4.98 V
    2.1 to 3.1 V
    (Fail-safe)
    VTA1 circuit open or ground short
    0.6 to 1.4 V
    (Fail-safe)
    0 to 0.2 V,
    or 4.5 to 4.98 V
    0.6 to 1.4 V
    (Fail-safe)
    0 to 0.2 V,
    or 4.5 to 4.98 V
    VTA2 circuit open or ground short
    0.5 to 1.1 V
    2.1 to 3.1 V
    3.2 to 4.8 V
    (Not fail-safe)
    4.6 to 4.98 V
    (Not fail-safe)
    Throttle position sensor circuit normal
    B

HINT:
  1. DTC P0121 is stored when the VTA1 and VTA2 output voltages are not consistent with the sensor characteristics. Therefore, check the freeze frame data when this DTC is stored. Use the following formula to confirm the relative differences in voltage.

    Characteristic Sensor Output:
    VTA2 x 0.8 is approximately equal to VTA1 + 1.11 V
    VTA1: Throttle Position No. 1
    VTA2: Throttle Position No. 2

  2. If DTC P0121 is output, proceed to "Check Harness And Connector (Throttle Position Sensor - ECM)".



B
Go to step 5
A


2.CHECK HARNESS AND CONNECTOR (THROTTLE POSITION SENSOR - ECM)
  1. Disconnect the throttle with motor body assembly connector.

  1. Disconnect the ECM connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:

    Tester Connection
    Condition
    Specified Condition
    E16-5 (VC) - E83-67 (VCTA)
    Always
    Below 1 Ω
    E16-6 (VTA) - E83-115 (VTA1)
    Always
    Below 1 Ω
    E16-4 (VTA2) - E83-114 (VTA2)
    Always
    Below 1 Ω
    E16-3 (E2) - E83-91 (ETA)
    Always
    Below 1 Ω
    E16-5 (VC) or E83-67 (VCTA) - Body ground
    Always
    10 kΩ or higher
    E16-6 (VTA) or E83-115 (VTA1) - Body ground
    Always
    10 kΩ or higher
    E16-4 (VTA2) or E83-114 (VTA2) - Body ground
    Always
    10 kΩ or higher



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK


3.INSPECT ECM (VC VOLTAGE)


    A194103E42
  1. Disconnect the throttle with motor body assembly connector.

  1. Turn the ignition switch to ON.

  1. Measure the voltage according to the value(s) in the table below.

    Standard Voltage:
    Tester Connection
    Condition
    Specified Condition
    E16-5 (VC) - E16-3 (E2)
    Ignition switch ON
    4.5 to 5.5 V

    Text in Illustration 
    *a
    Front view of wire harness connector
    (to Throttle with Motor Body Assembly)



NG
REPLACE ECM (Click here)
OK


4.REPLACE THROTTLE WITH MOTOR BODY ASSEMBLY
  1. Replace the throttle with motor body assembly (Click here).


NEXT


5.CHECK WHETHER DTC OUTPUT RECURS (THROTTLE POSITION SENSOR DTCS)
  1. Connect the intelligent tester to the DLC3.

  1. Turn the ignition switch to ON.

  1. Turn the tester on.

  1. Clear the DTCs (Click here).

  1. Turn the ignition switch off and wait for at least 30 seconds.

  1. Turn the ignition switch to ON.

  1. Turn the tester on.

  1. Drive the vehicle in accordance with the driving pattern described in Confirmation Driving Pattern.

  1. Enter the following menus: Powertrain / Engine and ECT / DTC.

  1. Read the DTCs.

    Result 
    Result
    Proceed to
    DTC P0120, P0121, P0122, P0123, P0220, P0222, P0223 and/or P2135 are output
    A
    DTC is not output
    B



B
END
A

REPLACE ECM (Click here)