DTC P2120 Throttle / Pedal Position Sensor / Switch "D" Circuit |
DTC P2122 Throttle / Pedal Position Sensor / Switch "D" Circuit Low Input |
DTC P2123 Throttle / Pedal Position Sensor / Switch "D" Circuit High Input |
DTC P2125 Throttle / Pedal Position Sensor / Switch "E" Circuit |
DTC P2127 Throttle / Pedal Position Sensor / Switch "E" Circuit Low Input |
DTC P2128 Throttle / Pedal Position Sensor / Switch "E" Circuit High Input |
DTC P2138 Throttle / Pedal Position Sensor / Switch "D" / "E" Voltage Correlation |

| DTC No. | DTC Detection Condition | Trouble Area |
| P2120 | VPA fluctuates rapidly beyond the upper and lower malfunction thresholds for 0.5 seconds or more (1 trip detection logic). |
|
| P2122 | VPA is 0.4 V or less for 0.5 seconds or more when the accelerator pedal is depressed (1 trip detection logic). |
|
| P2123 | VPA is 4.8 V or higher for 2.0 seconds or more (1 trip detection logic). |
|
| P2125 | VPA2 fluctuates rapidly beyond the upper and lower malfunction thresholds for 0.5 seconds or more (1 trip detection logic). |
|
| P2127 | VPA2 is 1.2 V or less for 0.5 seconds or more when the accelerator pedal is depressed (1 trip detection logic). |
|
| P2128 | Both of the following conditions continue for 2.0 seconds or more (1 trip detection logic): (a) VPA2 is 4.8 V or higher. (b) VPA is between 0.4 V and 3.45 V. |
|
| P2138 | Either of the following conditions continues for 2.0 seconds or more (1 trip detection logic): (a) The difference between VPA and VPA2 is 0.02 V or less. (b) VPA is 0.4 V or less, and VPA2 is 1.2 V or less. |
|
| Trouble Area | Accelerator Pedal Fully Released | Accelerator Pedal Fully Depressed | ||
| Accel Sensor Out No. 1 | Accel Sensor Out No. 2 | Accel Sensor Out No. 1 | Accel Sensor Out No. 2 | |
| Open in VCP circuit | 0 to 0.2 V | 0 to 0.2 V | 0 to 0.2 V | 0 to 0.2 V |
| Open or ground short in VPA circuit | 0 to 0.2 V | 1.2 to 2.0 V | 0 to 0.2 V | 3.4 to 4.98 V |
| Open or ground short in VPA2 circuit | 0.5 to 1.1 V | 0 to 0.2 V | 2.6 to 4.5 V | 0 to 0.2 V |
| Open in EPA circuit | 4.5 to 4.98 V | 4.5 to 4.98 V | 4.5 to 4.98 V | 4.5 to 4.98 V |
| Normal condition | 0.5 to 1.1 V | 1.2 to 2.0 V | 2.6 to 4.5 V | 3.4 to 4.98 V |
| Required Sensors/Components | Accelerator pedal sensor assembly |
| Frequency of Operation | Continuous |
| VPA voltage | Higher than 0.4 V, and less than 4.8 V |
| VPA2 voltage | Higher than 1.2 V, and less than 4.8 V |
| Difference between VPA and VPA2 voltages | Higher than 0.02 V |

| Tester Display | Description |
| NORMAL |
|
| ABNORMAL |
|
| INCOMPLETE |
|
| N/A |
|

| 1.READ VALUE USING INTELLIGENT TESTER (ACCEL SENSOR OUT) |
![]() |
Connect the intelligent tester to the DLC3.
Turn the engine switch on (IG).
Turn the tester on.
Enter the following menus: Powertrain / Engine / Data List / All Data / Accel Sensor Out No. 1 and Accel Sensor Out No. 2.
Read the value displayed on the tester.
| Accelerator Pedal Operation | Accel Sensor Out No. 1 | Accel Sensor Out No. 2 |
| Fully Released | 0.5 to 1.1 V | 1.2 to 2.0 V |
| Fully Depressed | 2.6 to 4.5 V | 3.4 to 4.98 V |
| *a | Fully Depressed |
| *b | Fully Released |
|
| ||||
| OK | ||
| ||
| 2.CHECK HARNESS AND CONNECTOR (ACCELERATOR PEDAL SENSOR ASSEMBLY - ECM) |
Disconnect the accelerator pedal sensor assembly connector.
Disconnect the ECM connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
| A36-6 (VPA) - A25-54 (VPA) | Always | Below 1 Ω |
| A36-5 (EPA) - A25-55 (EPA) | Always | Below 1 Ω |
| A36-4 (VCPA) - A25-56 (VCPA) | Always | Below 1 Ω |
| A36-3 (VPA2) - A25-57 (VPA2) | Always | Below 1 Ω |
| A36-2 (EPA2) - A25-58 (EPA2) | Always | Below 1 Ω |
| A36-1 (VCP2) - A25-59 (VCP2) | Always | Below 1 Ω |
| A36-6 (VPA) or A25-54 (VPA) - Body ground | Always | 10 kΩ or higher |
| A36-4 (VCPA) or A25-56 (VCPA) - Body ground | Always | 10 kΩ or higher |
| A36-3 (VPA2) or A25-57 (VPA2) - Body ground | Always | 10 kΩ or higher |
| A36-1 (VCP2) or A25-59 (VCP2) - Body ground | Always | 10 kΩ or higher |
|
| ||||
| OK | |
| 3.CHECK TERMINAL VOLTAGE (POWER SOURCE OF ACCELERATOR PEDAL SENSOR ASSEMBLY) |
![]() |
Disconnect the accelerator pedal sensor assembly connector.
Turn the engine switch on (IG).
Measure the voltage according to the value(s) in the table below.
| Tester Connection | Switch Condition | Specified Condition |
| A36-4 (VCPA) - A36-5 (EPA) | Engine switch on (IG) | 4.5 to 5.5 V |
| A36-1 (VCP2) - A36-2 (EPA2) | Engine switch on (IG) | 4.5 to 5.5 V |
| *a | Front view of wire harness connector (to Accelerator Pedal Sensor Assembly) |
|
| ||||
| OK | |
| 4.REPLACE ACCELERATOR PEDAL SENSOR ASSEMBLY |
Replace the accelerator pedal sensor assembly (Click here).
| NEXT | |
| 5.CHECK WHETHER DTC OUTPUT RECURS (ACCELERATOR PEDAL SENSOR DTCS) |
Connect the intelligent tester to the DLC3.
Turn the engine switch on (IG).
Turn the tester on.
Clear the DTCs (Click here).
Turn the engine switch off and wait for at least 30 seconds.
Turn the engine switch on (IG) and turn the tester on.
Drive the vehicle in accordance with the driving pattern described in Confirmation Driving Pattern.
Enter the following menus: Powertrain / Engine / DTC.
Read the DTCs.
| Result | Proceed to |
| DTC P2120, P2122, P2123, P2125, P2127, P2128, and/or P2138 are output | A |
| DTC is not output | B |
|
| ||||
| A | ||
| ||