Home › Vehicle Exterior › LIGHTING (EXT) › AUTOMATIC HEADLIGHT BEAM LEVEL CONTROL SYSTEM

AUTOMATIC HEADLIGHT BEAM LEVEL CONTROL SYSTEM > TERMINALS OF ECU

for Preparation Click here



CHECK HEADLIGHT LEVELING ECU ASSEMBLY


  1. Disconnect the A34 headlight leveling ECU assembly connector.


    E101528E20

  2. Measure the voltage and resistance according to the value(s) in the table below.

    Standard Voltage 
    Terminal No. (Symbol)
    Wiring Color
    Terminal Description
    Condition
    Specified Condition
    A34-1 (IG) - Body ground
    LG - Body ground
    IG power supply
    Ignition switch off
    Below 1 V
    Ignition switch ON
    11 to 14 V

    Standard Resistance 
    Terminal No. (Symbol)
    Wiring Color
    Terminal Description
    Condition
    Specified Condition
    A34-9 (E1) - Body ground
    W-B - Body ground
    Ground
    Always
    Below 1 Ω
    If the result is not as specified, there may be a malfunction on the wire harness side.

  3. Reconnect the A34 headlight leveling ECU assembly connector.



  4. Measure the resistance and voltage according to the value(s) in the table below.

    Standard Resistance 
    Terminal No. (Symbol)
    Wiring Color
    Terminal Description
    Condition
    Specified Condition
    A34-21 (SGR) - Body ground
    V - Body ground
    Rear height control sensor ground
    Always
    Below 1 Ω
    A34-23 (RH-) - Body ground
    G - Body ground
    Leveling motor RH ground
    Always
    Below 1 Ω
    A34-24 (LH-) - Body ground
    B - Body ground
    Leveling motor LH ground
    Always
    Below 1 Ω

    Standard Voltage 
    Terminal No. (Symbol)
    Wiring Color
    Terminal Description
    Condition
    Specified Condition
    A34-3 (B2) - Body ground
    G - Body ground
    Low beam headlight signal input
    Low beam headlights on
    Below 1.5 V
    Low beam headlights off
    5 V or higher
    A34-5 (SPDL) - Body ground
    V - Body ground
    Initialization signal input
    Terminals LVL and GND of DLC3 connected
    Below 1 V
    Terminals LVL and GND of DLC3 not connected
    4.5 to 5.5 V
    A34-6 (WNG) - Body ground
    SB - Body ground
    Warning indicator drive output
    Warning indicator on
    Below 1 V
    Warning indicator off
    11 to 14 V
    A34-10 (RH+) - Body ground
    R - Body ground
    Leveling motor RH power supply
    Ignition switch off
    Below 1 V
    Ignition switch ON
    11 to 14 V
    A34-11 (LH+) - Body ground
    Y - Body ground
    Leveling motor LH power supply
    Ignition switch off
    Below 1 V
    Ignition switch ON
    11 to 14 V
    A34-12 (SBR) - Body ground
    B - Body ground
    Rear height control sensor power supply
    Ignition switch off
    Below 1 V
    Ignition switch ON
    4.75 to 5.25 V
    A34-16 (SPDR) - Body ground
    P - Body ground
    Vehicle speed signal input
    Vehicle driven at approx. 20 km/h (12mph)
    Pulse generation
    (See waveform 1)
    A34-17 (RHE) - Body ground
    W - Body ground
    Leveling motor RH operation signal input
    With low beam headlights on, vehicle height not changed
    Below 1 V
    With low beam headlights on, vehicle height changed and maintained for more than 3 seconds
    1.0 to 14.4 V
    A34-18 (LHE) - Body ground
    LG - Body ground
    Leveling motor LH operation signal input
    With low beam headlights on, vehicle height not changed
    Below 1 V
    With low beam headlights on, vehicle height changed and maintained for more than 3 seconds
    1.0 to 14.4 V
    A34-19 (SHRL) - Body ground
    R - Body ground
    Rear height control sensor signal input
    Ignition switch off
    Below 1 V
    Ignition switch ON
    0.5 to 4.5 V
    If the result is not as specified, the headlight leveling ECU assembly may have a malfunction.



      E149152E01
    1. Waveform 1
      Item
      Content
      Tool setting
      2 V/DIV., 2 ms./DIV.
      Vehicle condition
      Wheel being rotated