Home › Vehicle Exterior › LIGHTING (EXT) › AFS (ADAPTIVE FRONT-LIGHTING SYSTEM)

AFS (ADAPTIVE FRONT-LIGHTING SYSTEM) > DATA LIST / ACTIVE TEST

for Preparation Click here



DATA LIST

HINT:
Using the intelligent tester to read the Data List allows the values or states of switches, sensors, actuators and other items to be read without removing any parts. This non-intrusive inspection can be very useful because intermittent conditions or signals may be discovered before parts or wiring is disturbed. Reading the Data List information early in troubleshooting is one way to save diagnostic time.

NOTICE:
In the table below, the values listed under "Normal Condition" are reference values. Do not depend solely on these reference values when deciding whether a part is faulty or not.

  1. Connect the intelligent tester to the DLC3.

  2. Turn the ignition switch to ON.

  3. Turn the intelligent tester on.

  4. Enter the following menus: Body / AFS / Data List.

  5. Read the Data List according to the display on the intelligent tester.

    AFS 
    Tester Display
    Measurement Item/Range
    Normal Condition
    Diagnostic Note
    AFS OFF Switch
    AFS OFF switch signal/ON or OFF
    ON: AFS off
    OFF: AFS on
    -
    Traveling Direction
    Traveling Direction/Not Fwd or Fwd
    Not Fwd: Shift lever in R or N
    Fwd: Shift lever not in R or N
    -
    Headlight Low Beam State
    Low beam headlight state/ON or OFF
    ON: Low beam headlights on
    OFF: Low beam headlights off
    -
    Headlight High Beam State
    High beam headlight state/ON or OFF
    ON: High beam headlights on
    OFF: High beam headlights off
    -
    Engine
    Engine condition/Run or Stop
    Run: Engine running
    Stop: Engine stopped
    -
    +B
    IG power supply voltage value/0.00 to 19.75 V
    11 to 14 V
    -
    Height Sens Pw Supply Val
    Height control sensor power supply value/0.00 to 6.25 V
    Approx. 5 V
    -
    Rr Height Sens Signal Val
    Rear height control sensor signal value/0.00 to 5.00 V
    Approx. 2.5 V (When vehicle is level)
    Value changes according to vehicle height
    Steering Sens Signal
    Steering angle sensor signal value/-384.0 deg to 382.5 deg
    Approx. 0 deg (When steering wheel is straight)
    Value changes according to steering wheel position
    Steering Sens Center Pos
    Steering angle sensor center position/-3072.0 deg to 3070.5 deg
    Condition can be displayed
    -
    FR Wheel Speed
    Front right wheel speed/0.00 to 327.67 km/h (203.61 mph)
    Condition can be displayed
    -
    FL Wheel Speed
    Front left wheel speed/0.00 to 327.67 km/h (203.61 mph)
    Condition can be displayed
    -
    Vehicle Speed
    Vehicle speed/0.00 to 327.67 km/h (203.61 mph)
    Condition can be displayed
    -
    Rear Height Adjust Valid Flag
    Rear height adjustment range/Valid or Invalid
    Condition can be displayed
    -
    Init Writing Count
    Number of times for initialization/0 to 255
    Condition can be displayed
    -
    Sensor Initialization Hist
    Sensor Initialization History/not comp, 10%, 25%, 50%, 75%, 100% or complied
    Condition can be displayed
    -
    L Swivel Target Step
    Swivel motor LH target step value/0 to 400 step
    34 to 286 step
    -
    L Swivel Current Step
    Swivel motor LH current step value/0 to 400 step
    34 to 286 step
    -
    R Swivel Target Step
    Swivel motor RH target step value/0 to 400 step
    8 to 185 step
    -
    R Swivel Current Step
    Swivel motor RH current step value/0 to 400 step
    8 to 185 step
    -
    LR Leveling Target Step
    Leveling motor LH and RH target step value/0 to 300 step
    5 to 247 step
    -
    L Leveling Current Step
    Leveling motor LH current step value/0 to 300 step
    5 to 247 step
    -
    R Leveling Current Step
    Leveling motor RH current step value/0 to 300 step
    5 to 247 step
    -
    Number Of Trouble Codes
    Number of trouble codes/0 to 255
    Condition can be displayed
    -


ACTIVE TEST

HINT:
Using the intelligent tester to perform Active Tests allows relays, VSVs, actuators and other items to be operated without removing any parts. This non-intrusive functional inspection can be very useful because intermittent operation may be discovered before parts or wiring is disturbed. Performing Active Tests early in troubleshooting is one way to save diagnostic time. Data List information can be displayed while performing Active Tests.

  1. Connect the intelligent tester to the DLC3.

  2. Turn the ignition switch to ON.

  3. Turn the intelligent tester on.

  4. Enter the following menus: Body / AFS / Active Test.

  5. Perform the Active Test according to the display on the intelligent tester.

    AFS 
    Tester Display
    Test Part
    Control Range
    Diagnostic Note
    Drive The Leveling Motor UP*1
    Leveling motor upward operation
    ON/OFF
    ON: Moves up
    OFF: Stops
    Drive The Leveling Motor DOWN*1
    Leveling motor downward operation
    ON/OFF
    ON: Moves down
    OFF: Stops
    Drive Swivel Motor LH LEFT*1
    Swivel motor LH left direction rotation
    ON/OFF
    ON: Moves left
    OFF: Stops
    Drive Swivel Motor LH RIGHT*1
    Swivel motor LH right direction rotation
    ON/OFF
    ON: Moves right
    OFF: Stops
    Drive Swivel Motor RH LEFT*1
    Swivel motor RH left direction rotation
    ON/OFF
    ON: Moves left
    OFF: Stops
    Drive Swivel Motor RH RIGHT*1
    Swivel motor RH right direction rotation
    ON/OFF
    ON: Moves right
    OFF: Stops
    AFS OFF Indicator
    AFS OFF indicator
    ON/OFF
    -
    *1: Perform the active test with the engine started and vehicle stopped.