Home › Engine / Hybrid System ยท CRUISE CONTROL › CRUISE CONTROL SYSTEM

CRUISE CONTROL SYSTEM > DATA LIST / ACTIVE TEST

for Preparation Click here



READ DATA LIST

HINT:
Using the intelligent tester to read the Data List allows the values or states of switches, sensors, actuators and other items to be read without removing any parts. This non-intrusive inspection can be very useful because intermittent conditions or signals may be discovered before parts or wiring is disturbed. Reading the Data List information early in troubleshooting is one way to save diagnostic time.

  1. Connect the intelligent tester to the DLC3.

  2. Turn the ignition switch to ON.

  3. Turn the intelligent tester on.

  4. Select the following menu items: Powertrain / Cruise Control / Data List.

  5. Read the Data List according to the display on the intelligent tester.

    Cruise Control 
    Tester Display
    Measurement Item/Range
    Normal Condition
    Diagnostic Note
    CCS Vehicle Spd
    Vehicle speed / Min.: 0 km/h (0 mph), Max.: 255 km/h (158 mph)
    Actual vehicle speed
    -
    CCS Mem Vehicle Spd
    Stored vehicle speed / Min.: 0 km/h (0 mph), Max.: 255 km/h (158 mph)
    Actual stored vehicle speed
    -
    Throttle Opening Angle
    Required throttle opening angle / min.: 0°, max.: 124.50°
    Actual required throttle opening angle
    -
    Cruise Control
    Cruise control system active condition / ON or OFF
    ON: Cruise control activated
    OFF: Cruise control deactivated
    -
    Main SW M-CPU
    Cruise control switch signal (Main CPU) / ON or OFF
    ON: Cruise control switch (ON-OFF button) pushed
    OFF: Cruise control switch (ON-OFF button) released
    -
    CCS Ready M-CPU
    Cruise control system standby condition (Main CPU) / ON or OFF
    Each time cruise control switch (ON-OFF button) is pushed, ON/OFF changes
    -
    CCS Indicator M-CPU
    Cruise control indicator light illumination signal (Main CPU) / ON or OFF
    ON: Cruise control indicator light illuminated in green
    OFF: Cruise control indicator light not on
    -
    Cancel Switch
    CANCEL switch signal / ON or OFF
    ON: CANCEL switch on
    OFF: CANCEL switch off
    -
    SET/COAST Switch
    -/SET switch signal / ON or OFF
    ON: -/SET switch on
    OFF: -/SET switch off
    -
    RES/ACC Switch
    +/RES switch signal / ON or OFF
    ON: +/RES switch on
    OFF: +/RES switch off
    -
    Stp Light SW M-CPU
    Stop light switch signal (Main CPU) / ON or OFF
    ON: Brake pedal depressed
    OFF: Brake pedal released
    -
    Cruise Operation Status
    Transmission range sensor signal / ON or OFF
    ON: Cruise control operated
    OFF: Cruise control operation stopped
    -
    Brake Cancel Switch
    Brake cancel signal / ON or OFF
    ON: Brake pedal depressed
    OFF: Brake pedal released
    -

    HINT:
    1. If any DTCs are output, the value for a measurement item may be incorrect.
    1. If any DTCs are output, perform troubleshooting accordingly. After repair, confirm relevant values using Data List.


PERFORM ACTIVE TEST

HINT:
Using the intelligent tester to perform Active Tests allows relays, VSVs, actuators and other items to be operated without removing any parts. This non-intrusive functional inspection can be very useful because intermittent operation may be discovered before parts or wiring is disturbed. Performing Active Tests early in troubleshooting is one way to save diagnostic time. Data List information can be displayed while performing Active Tests.

  1. Connect the intelligent tester to the DLC3.

  2. Turn the ignition switch to ON.

  3. Turn the intelligent tester on.

  4. Select the following menu items: Body / Combination Meter / Active Test.

  5. Perform "Active Test" according to the display on intelligent tester.

    HINT:
    The ignition switch must be turned on to proceed with the Active Test using the intelligent tester.


    Combination Meter 
    Tester Display
    Test Part
    Control Range
    Diagnostic Note
    Indicat. Lamp Cruise
    Cruise control indicator light
    Cruise control indicator light (illuminated in green) ON / OFF
    -
    Indicat. Lamp SET
    Cruise control SET indicator light
    Cruise control SET indicator light ON / OFF
    -
    Cruise indicator*
    Cruise control indicator light
    Cruise control indicator light (illuminated in amber) ON / OFF
    -
    *: w/o Multi-information Display