ENGINE IMMOBILISER SYSTEM (w/ Smart Entry and Start System) > TERMINALS OF ECU |
| CHECK ENGINE SWITCH |

Measure the resistance and voltage according to the value(s) in the table below.
| Terminal No. (Symbol) | Input/Output | Wiring Color | Terminal Description | Condition | Specified Condition | Related Data List Item/DTC |
| I58-6 (AGND) - Body ground | - | G - Body ground | Transponder key amplifier ground | Always | Below 1 Ω | - |
| I58-7 (TXCT) - I58-6 (AGND) | Input | GR - G | Immobiliser communication input | Engine switch off, brake pedal not depressed, 30 seconds or more elapsed after driver door opened and then closed | Below 1 V | - |
| I58-8 (CODE) - I58-6 (AGND) | Output | SB - G | Immobiliser communication output | Engine switch off, brake pedal not depressed, 30 seconds or more elapsed after driver door opened and then closed | Below 1 V | - |
| I58-10 (VC5) - I58-6 (AGND) | Input | LG - G | Transponder key amplifier power supply | Engine switch off, brake pedal not depressed, 30 seconds or more elapsed after driver door opened and then closed | Below 1 V | - |
Check for pulses according to the value(s) in the table below.
| Terminal No. (Symbol) | Input/Output | Wiring Color | Terminal Description | Condition | Specified Condition | Related Data List Item/DTC |
| I58-7 (TXCT) - I58-6 (AGND) | Input | GR - G | Signal input from certification ECU (smart key ECU assembly) (Code sent from certification ECU (smart key ECU assembly) to transponder key amplifier built into engine switch, and then transmitted by transponder key amplifier antenna as radio waves) | Engine switch off, key not in cabin, within 30 seconds after engine switch pressed | Pulse generation (See waveform 1) |
|
| I58-8 (CODE) - I58-6 (AGND) | Output | SB - G | Signal output to certification ECU (smart key ECU assembly) (Radio waves from transponder key amplifier built into engine switch used to detect key information. Key information then sent to certification ECU (smart key ECU assembly)) | Engine switch off, engine switch pressed with key held near engine switch* | Pulse generation (See waveform 2) | |
| I58-10 (VC5) - I58-6 (AGND) | Input | LG - G | Transponder key amplifier power supply (Power supplied from certification ECU (smart key ECU assembly) when transponder key amplifier built into engine switch activated) | Engine switch off, key not in cabin, within 30 seconds after engine switch pressed | Pulse generation (See waveform 3) |
Inspect using an oscilloscope.
![]() |
Waveform 1 (Reference)
| Item | Content |
| Tester Connection | I58-7 (TXCT) - I58-6 (AGND) |
| Tool Setting | 2 V/DIV., 20 ms./DIV. |
| Condition | Engine switch off, key not in cabin, within 30 seconds after engine switch pressed |
![]() |
Waveform 2 (Reference)
| *a | Key held against engine switch |
| Item | Content |
| Tester Connection | I58-8 (CODE) - I58-6 (AGND) |
| Tool Setting | 1 V/DIV., 200 ms./DIV. |
| Condition | Engine switch off, engine switch pressed with key held near engine switch* |
![]() |
Waveform 3 (Reference)
| Item | Content |
| Tester Connection | I58-10 (VC5) - I58-6 (AGND) |
| Tool Setting | 2 V/DIV., 200 ms./DIV. |
| Condition | Engine switch off, key not in cabin, within 30 seconds after engine switch pressed |
| CHECK CERTIFICATION ECU (SMART KEY ECU ASSEMBLY) |

Disconnect the A43 ECU connector.
Measure the resistance and voltage according to the value(s) in the table below.
| Terminal No. (Symbol) | Input/Output | Wiring Color | Terminal Description | Condition | Specified Condition | Related Data List Item/DTC |
| A43-2 (+B) - A43-11 (E) | Input | W - W | +B power supply | Always | 11 to 14 V | - |
| A43-10 (CUTB) - A43-11 (E) | Input | L - W | Dark current cut pin | Always | 11 to 14 V | - |
| A43-11 (E) - Body ground | - | W - Body ground | Ground | Always | Below 1 Ω | - |
Reconnect the A43 ECU connector.
Measure the resistance and voltage according to the value(s) in the table below.
| Terminal No. (Symbol) | Input/Output | Wiring Color | Terminal Description | Condition | Specified Condition | Related Data List Item/DTC |
| I78-5 (IG) - A43-11 (E) | Input | LG - W | Ignition power supply | Engine switch off → on (IG) | Below 1 V → 11 to 14 V | Ignition Switch |
| I78-18 (IND) - A43-11 (E) | Output | L - W | Security indicator output | Engine switch off → on (IG) | Pulse generation → Below 2 V | - |
| I78-9 (TXCT) - I78-24 (AGND) | Output | GR - G | Signal output to transponder key amplifier | Engine switch off, brake pedal not depressed, 30 seconds or more elapsed after driver door opened and then closed | Below 1 V |
|
| I78-7 (CODE) - I78-24 (AGND) | Input | SB - G | Signal input from transponder key amplifier | Engine switch off, brake pedal not depressed, 30 seconds or more elapsed after driver door opened and then closed | Below 1 V | |
| I78-1 (VC5) - I78-24 (AGND) | Output | LG - G | Transponder key amplifier power supply | Engine switch off, brake pedal not depressed, 30 seconds or more elapsed after driver door opened and then closed | Below 1 V | |
| I78-24 (AGND) - Body ground | - | G - Body ground | Transponder key amplifier ground | Always | Below 1 Ω | |
| A43-14 (EFII) - A43-11 (E)*1 | Input | SB*2, G*3 - W | EFI communication input (Signal input from ECM to certification ECU (smart key ECU assembly)) | Engine switch off | 11 to 14 V |
|
| A43-13 (EFIO) - A43-11 (E)*1 | Output | Y - W | EFI communication output (Signal output from certification ECU (smart key ECU assembly) to ECM) | Engine switch off | Below 1 V |
Check for pulses according to the value(s) in the table below.
| Terminal No. (Symbol) | Input/Output | Wiring Color | Terminal Description | Condition | Specified Condition | Related Data List Item/DTC |
| I78-9 (TXCT) - I78-24 (AGND) | Output | GR - G | Signal output to transponder key amplifier (Code sent from certification ECU (smart key ECU assembly) to transponder key amplifier built into engine switch, and then transmitted by transponder key amplifier antenna as radio waves) | Engine switch off, key not in cabin, within 30 seconds after engine switch pressed | Pulse generation (See waveform 1) |
|
| I78-7 (CODE) - I78-24 (AGND) | Input | SB - G | Signal input from transponder key amplifier (Radio waves from transponder key amplifier built into engine switch used to detect key information. Key information then sent to certification ECU (smart key ECU assembly)) | Engine switch off, engine switch pressed with key held near engine switch* | Pulse generation (See waveform 2) | |
| I78-1 (VC5) - I78-24 (AGND) | Output | LG - G | Transponder key amplifier power supply (Power supplied from certification ECU (smart key ECU assembly) when transponder key amplifier built into engine switch activated) | Engine switch off, key not in cabin, within 30 seconds after engine switch pressed | Pulse generation (See waveform 3) | |
| A43-14 (EFII) - A43-11 (E)*1 | Input | SB*2, G*3 - W | EFI communication input (Signal input from ECM to certification ECU (smart key ECU assembly)) | Within 3 seconds of engine start or within 3 seconds of engine switch turned on (IG) after battery cable disconnected and reconnected | Pulse generation (See waveform 4) |
|
| A43-13 (EFIO) - A43-11 (E)*1 | Output | Y - W | EFI communication output (Signal output from certification ECU (smart key ECU assembly) to ECM) | Within 3 seconds of engine start or within 3 seconds of engine switch turned on (IG) after battery cable disconnected and reconnected | Pulse generation (See waveform 5) |
Inspect using an oscilloscope.
![]() |
Waveform 1 (Reference)
| Item | Content |
| Tester Connection | I78-9 (TXCT) - I78-24 (AGND) |
| Tool Setting | 2 V/DIV., 20 ms./DIV. |
| Condition | Engine switch off, key not in cabin, within 30 seconds after engine switch pressed |
![]() |
Waveform 2 (Reference)
| *a | Key held against engine switch |
| Item | Content |
| Tester Connection | I78-7 (CODE) - I78-24 (AGND) |
| Tool Setting | 1 V/DIV., 200 ms./DIV. |
| Condition | Engine switch off, engine switch pressed with key held near engine switch* |
![]() |
Waveform 3 (Reference)
| Item | Content |
| Tester Connection | I78-1 (VC5) - I78-24 (AGND) |
| Tool Setting | 2 V/DIV., 200 ms./DIV. |
| Condition | Engine switch off, key not in cabin, within 30 seconds after engine switch pressed |
Waveform 4 (Reference)*1

| *a | Approximately 160 ms | *b | Approximately 270 ms |
| Item | Content |
| Tester Connection | A43-14 (EFII) - A43-11 (E) |
| Tool Setting | 2 V/DIV., 500 ms./DIV. |
| Condition | Within 3 seconds of engine start or within 3 seconds of engine switch turned on (IG) after battery cable disconnected and reconnected |
Waveform 5 (Reference)*1

| *a | Approximately 160 ms | *b | Approximately 270 ms |
| Item | Content |
| Tester Connection | A43-13 (EFIO) - A43-11 (E) |
| Tool Setting | 2 V/DIV., 500 ms./DIV. |
| Condition | Within 3 seconds of engine start or within 3 seconds of engine switch turned on (IG) after battery cable disconnected and reconnected |
| CHECK ID CODE BOX (IMMOBILISER CODE ECU) (w/o Wireless Door Lock Buzzer Answer Back Function) |

Disconnect the I20 ECU connector.
Measure the resistance and voltage according to the value(s) in the table below.
| Terminal No. (Symbol) | Input/Output | Wiring Color | Terminal Description | Condition | Specified Condition | Related Data List Item/DTC |
| I20-1 (+B) - I20-5 (GND) | Input | W - W-B | +B power supply | Always | 11 to 14 V | B2789 |
| I20-5 (GND) - Body ground | - | W-B - Body ground | Ground | Always | Below 1 Ω | B2789 |
Reconnect the I20 ECU connector.
Measure the voltage according to the value(s) in the table below.
| Terminal No. (Symbol) | Input/Output | Wiring Color | Terminal Description | Condition | Specified Condition | Related Data List Item/DTC |
| I20-3 (EFII) - I20-5 (GND) | Input | R - W-B | EFI communication input (Signal input from ECM to ID code box (immobiliser code ECU)) | Engine switch off | 11 to 14 V |
|
| I20-3 (EFII) - I20-5 (GND) | Input | R - W-B | EFI communication input (Signal input from ECM to ID code box (immobiliser code ECU)) | Within 3 seconds of engine start or within 3 seconds of engine switch turned on (IG) after battery cable disconnected and reconnected | Pulse generation (See waveform 1) | |
| I20-4 (EFIO) - I20-5 (GND) | Output | G - W-B | EFI communication output (Signal output from ID code box (immobiliser code ECU) to ECM) | Engine switch off | Below 1 V | |
| I20-4 (EFIO) - I20-5 (GND) | Output | G - W-B | EFI communication output (Signal output from ID code box (immobiliser code ECU) to ECM) | Within 3 seconds of engine start or within 3 seconds of engine switch turned on (IG) after battery cable disconnected and reconnected | Pulse generation (See waveform 2) |
Inspect using an oscilloscope.
Waveform 1 (Reference)

| *a | Approximately 160 ms | *b | Approximately 270 ms |
| Item | Content |
| Tester Connection | I20-3 (EFII) - I20-5 (GND) |
| Tool Setting | 2 V/DIV., 500 ms./DIV. |
| Condition | Within 3 seconds of engine start or within 3 seconds of engine switch turned on (IG) after battery cable disconnected and reconnected |
Waveform 2 (Reference)

| *a | Approximately 160 ms | *b | Approximately 270 ms |
| Item | Content |
| Tester Connection | I20-4 (EFIO) - I20-5 (GND) |
| Tool Setting | 2 V/DIV., 500 ms./DIV. |
| Condition | Within 3 seconds of engine start or within 3 seconds of engine switch turned on (IG) after battery cable disconnected and reconnected |
| CHECK STEERING LOCK ECU (STEERING LOCK ACTUATOR ASSEMBLY) |

Measure the voltage and resistance according to the value(s) in the table below.
| Terminal No. (Symbol) | Input/Output | Wiring Color | Terminal Description | Condition | Specified Condition | Related Data List Item/DTC |
| I24-1 (GND) - Body ground | - | W-B - Body ground | Ground | Always | Below 1 Ω | - |
| I24-3 (IGE) - I24-1 (GND) | Input | SB - W-B | Steering lock motor operation permission signal (motor operation permission signal supplied by certification ECU (smart key ECU assembly)) | Steering lock motor operates when both conditions met, and then door opened:
| Pulse generation (See waveform 1) |
|
| I24-4 (SLP1) - I24-1 (GND) | Output | P - W-B | Steering lock bar position signal (signal output from steering unlock sensor) | Steering locked → unlocked*1 | 11 to 14 V → Below 1.2 V |
|
| I24-6 (IG2) - I24-1 (GND) | Input | LG - W-B | IG signal (IG2 power supply input for steering lock motor) | Engine switch off → on (IG) | Below 1 V → 11 to 14 V |
|
| I24-7 (B) - Body ground | Output | B - Body ground | Constant power supply | Always | 11 to 14 V | B2788 |
Inspect using an oscilloscope.
![]() |
Waveform 1 (Reference)
| *a | Steering lock motor not operating |
| *b | Steering lock motor operating |
| Item | Content |
| Tester Connection | I24-3 (IGE) - I24-1 (GND) |
| Tool Setting | 2 V/DIV., 20 ms./DIV. |
| Condition | Steering lock motor operates when both conditions met, and then door opened:
|
| CHECK ECM |

| Terminal No. (Symbol) | Input/Output | Wiring Color | Terminal Description | Condition | Specified Condition | Related Data List Item/DTC |
| E26-49 (E1) - Body ground | - | BR - Body ground | Ground | Always | Below 1 Ω | - |
| A25-1 (BATT) - E26-49 (E1) | Input | GR - BR | +B power supply | Always | 11 to 14 V | - |
| A25-2 (+B) - E26-49 (E1) | Input | P - BR | +B power supply | Engine switch on (IG) | 11 to 14 V | - |
| A25-3 (+B2) - E26-49 (E1) | Input | LG - BR | +B power supply | Engine switch on (IG) | 11 to 14 V | - |
| A25-30 (IMO) - E26-49 (E1) | Input | G*3, SB*4 - BR | Certification ECU (smart key ECU assembly)*1 or ID code box (immobiliser code ECU)*2 communication input | Engine switch off | Below 1 V*3 11 to 14 V*4 | - |
| A25-30 (IMO) - E26-49 (E1) | Input | G*3, SB*4 - BR | Certification ECU (smart key ECU assembly)*1 or ID code box (immobiliser code ECU)*2 communication input | Within 3 seconds of engine start or within 3 seconds of engine switch turned on (IG) after battery cable disconnected and reconnected | Pulse generation (See waveform 1) | - |
| A25-31 (IMI) - E26-49 (E1) | Output | Y - BR | Certification ECU (smart key ECU assembly)*1 or ID code box (immobiliser code ECU)*2 communication output | Engine switch off | Below 1 V | - |
| A25-31 (IMI) - E26-49 (E1) | Output | Y - BR | Certification ECU (smart key ECU assembly)*1 or ID code box (immobiliser code ECU)*2 communication output | Within 3 seconds of engine start or within 3 seconds of engine switch turned on (IG) after battery cable disconnected and reconnected | Pulse generation (See waveform 2) | - |
| Terminal No. (Symbol) | Input/Output | Wiring Color | Terminal Description | Condition | Specified Condition | Related Data List Item/DTC |
| E26-16 (E1) - Body ground | - | BR - Body ground | Ground | Always | Below 1 Ω | - |
| A25-1 (BATT) - E26-16 (E1) | Input | GR - BR | +B power supply | Always | 11 to 14 V | - |
| A25-2 (+B) - E26-16 (E1) | Input | P - BR | +B power supply | Engine switch on (IG) | 11 to 14 V | - |
| A25-3 (+B2) - E26-16 (E1) | Input | LG - BR | +B power supply | Engine switch on (IG) | 11 to 14 V | - |
| A25-29 (IMO) - E26-16 (E1) | Input | SB*1, G*2 - BR | Certification ECU (smart key ECU assembly)*1 or ID code box (immobiliser code ECU)*2 communication input | Engine switch off | 11 to 14 V | - |
| A25-29 (IMO) - E26-16 (E1) | Input | SB*1, G*2 - BR | Certification ECU (smart key ECU assembly)*1 or ID code box (immobiliser code ECU)*2 communication input | Within 3 seconds of engine start or within 3 seconds of engine switch turned on (IG) after battery cable disconnected and reconnected | Pulse generation (See waveform 1) | - |
| A25-28 (IMI) - E26-16 (E1) | Output | Y - BR | Certification ECU (smart key ECU assembly)*1 or ID code box (immobiliser code ECU)*2 communication output | Engine switch off | Below 1 V | - |
| A25-28 (IMI) - E26-16 (E1) | Output | Y - BR | Certification ECU (smart key ECU assembly)*1 or ID code box (immobiliser code ECU)*2 communication output | Within 3 seconds of engine start or within 3 seconds of engine switch turned on (IG) after battery cable disconnected and reconnected | Pulse generation (See waveform 2) | - |
Inspect using an oscilloscope.
Waveform 1 (Reference)

| *a | Approximately 160 ms | *b | Approximately 270 ms |
| Item | Content |
| Tester Connection | A25-30 (IMO) - E26-49 (E1)*1 A25-29 (IMO) - E26-16 (E1)*2 |
| Tool Setting | 2 V/DIV., 500 ms./DIV. |
| Condition | Within 3 seconds of engine start or within 3 seconds of engine switch turned on (IG) after battery cable disconnected and reconnected |
Waveform 2 (Reference)

| *a | Approximately 160 ms | *b | Approximately 270 ms |
| Item | Content |
| Tester Connection | A25-31 (IMI) - E26-49 (E1)*1 A25-28 (IMI) - E26-16 (E1)*2 |
| Tool Setting | 2 V/DIV., 500 ms./DIV. |
| Condition | Within 3 seconds of engine start or within 3 seconds of engine switch turned on (IG) after battery cable disconnected and reconnected |
| CHECK TELEPHONE TRANSCEIVER ASSEMBLY (w/ Blocking System) |
Disconnect the I70 telephone transceiver connector.

Measure the resistance and voltage according to the value(s) in the table below.
| Tester Connection | Input/Output | Wiring Color | Terminal Description | Condition | Specified Condition | Related Data List Item/DTC |
| I70-6 (IG2) - I70-9 (E) | Input | LG - BR | Ignition power supply | Engine switch on (IG) | 9 to 16 V | - |
| I70-12 (+B) - I70-9 (E) | Input | G - BR | +B power supply | Always | 9 to 16 V | - |
| I70-9 (E) - Body ground | - | BR - Body ground | Ground | Always | Below 1 Ω | - |
Reconnect the I70 telephone transceiver connector.
Measure the voltage according to the value(s) in the table below.
| Tester Connection | Input/Output | Wiring Color | Terminal Description | Condition | Specified Condition | Related Data List Item/DTC |
| I70-1 (BLK1) - I70-9 (E) | Input | L - BR | Certification ECU (smart key ECU assembly) communication input | Engine switch off | 11 to 14 V | - |
| I70-1 (BLK1) - I70-9 (E) | Input | L - BR | Certification ECU (smart key ECU assembly) communication input | Within 3 seconds of engine start or within 3 seconds of engine switch turned on (IG) after battery cable disconnected and reconnected | Pulse generation (See waveform 1) | - |
| I70-2 (BLK4) - I70-9 (E) | Output | Y - BR | Certification ECU (smart key ECU assembly) communication output | Engine switch off | Below 1 V | - |
| I70-2 (BLK4) - I70-9 (E) | Output | Y - BR | Certification ECU (smart key ECU assembly) communication output | Within 3 seconds of engine start or within 3 seconds of engine switch turned on (IG) after battery cable disconnected and reconnected | Pulse generation (See waveform 2) | - |
| I70-7 (BLK2) - I70-9 (E) | Output | R - BR | ECM communication output | Engine switch off | Below 1 V | - |
| I70-7 (BLK2) - I70-9 (E) | Output | R - BR | ECM communication output | Within 3 seconds of engine start or within 3 seconds of engine switch turned on (IG) after battery cable disconnected and reconnected | Pulse generation (See waveform 1) | - |
| I70-8 (BLK3) - I70-9 (E) | Input | G - BR | ECM communication input | Engine switch off | Below 1 V | - |
| I70-8 (BLK3) - I70-9 (E) | Input | G - BR | ECM communication input | Within 3 seconds of engine start or within 3 seconds of engine switch turned on (IG) after battery cable disconnected and reconnected | Pulse generation (See waveform 2) | - |
Inspect using an oscilloscope.
Waveform 1 (Reference)

| *a | Approximately 160 ms | *b | Approximately 270 ms |
| Item | Content |
| Tester Connection |
|
| Tool Setting | 2 V/DIV., 500 ms./DIV. |
| Condition | Within 3 seconds of engine start or within 3 seconds of engine switch turned on (IG) after battery cable disconnected and reconnected |
Waveform 2 (Reference)

| *a | Approximately 160 ms | *b | Approximately 270 ms |
| Item | Content |
| Tester Connection |
|
| Tool Setting | 2 V/DIV., 500 ms./DIV. |
| Condition | Within 3 seconds of engine start or within 3 seconds of engine switch turned on (IG) after battery cable disconnected and reconnected |