Home › Vehicle Interior › HEATING / AIR CONDITIONING › AIR CONDITIONING SYSTEM

DTC    B1446/46    Air Mix Damper Control Servo Motor Circuit (Driver Side)

for Preparation Click here


DESCRIPTION

  1. 1. for LHD
    The No. 2 air conditioning radiator damper servo sub-assembly (air mix for driver side) sends pulse signals to inform the air conditioning amplifier assembly of the damper position. The air conditioning amplifier assembly activates the motor (normal or reverse) based on the signals to move the No. 2 air conditioning radiator damper servo sub-assembly (air mix for driver side) to any position. As a result, the amount of air passing through the heater core after passing through the evaporator is adjusted, and the temperature of the air blowing toward the driver seat side is controlled.
    The air conditioning amplifier assembly communicates with the servo through a communication/driver IC and wiring assembly called the air conditioning harness assembly.

    HINT:
    Confirm that no mechanical problem is present because this diagnostic code can be output when either a damper link or the damper is mechanically locked.

  1. 2. for RHD
    The No. 1 air conditioning radiator damper servo sub-assembly (air mix for driver side) sends pulse signals to inform the air conditioning amplifier assembly of the damper position. The air conditioning amplifier assembly activates the motor (normal or reverse) based on the signals to move the No. 1 air conditioning radiator damper servo sub-assembly (air mix for driver side) to any position. As a result, the amount of air passing through the heater core after passing through the evaporator is adjusted, and the temperature of the air blowing toward the driver seat side is controlled.
    The air conditioning amplifier assembly communicates with the servo through a communication/driver IC and wiring assembly called the air conditioning harness assembly.

    HINT:
    Confirm that no mechanical problem is present because this diagnostic code can be output when either a damper link or the damper is mechanically locked.


DTC No.
DTC Detection Condition
Trouble Area
B1446/46
for LHD:
Air mix damper position sensor value does not change even if air conditioning amplifier assembly operates No. 2 air conditioning radiator damper servo sub-assembly (air mix for driver side)
for RHD:
Air mix damper position sensor value does not change even if air conditioning amplifier assembly operates No. 1 air conditioning radiator damper servo sub-assembly (air mix for driver side)
  1. No. 2 air conditioning radiator damper servo sub-assembly (air mix for driver side)*1
  2. No. 1 air conditioning radiator damper servo sub-assembly (air mix for driver side)*2
  3. Air conditioning harness assembly
  4. Air conditioning amplifier assembly
  1. *1: for LHD
  2. *2: for RHD

WIRING DIAGRAM


E229253E19


INSPECTION PROCEDURE

1.CONFIRM MODEL

Result:
Result
Proceed to
for LHD
A
for RHD
B



B
Go to step 6
A


2.READ VALUE USING INTELLIGENT TESTER
  1. Connect the intelligent tester to the DLC3.

  1. Turn the ignition switch to ON.

  1. Turn the intelligent tester on.

  1. Operate the driver side temperature adjustment switch.

  1. Enter the following menus: Body / Air Conditioner / Data List.

  1. Check the value(s) by referring to the table below.


Air Conditioner 
Tester Display
Measurement Item/Range
Normal Condition
Diagnostic Note
Air Mix Servo Actual Pulse(D)
No. 2 air conditioning radiator damper servo sub-assembly (air mix for driver side) actual pulse / Min.: 0, Max.: 255
MAX COLD: 5 (pulse)
MAX HOT: 103 (pulse)
-

OK:
The display is as specified in the normal condition column.


Result:

Result
Proceed to
NG
A
OK (When troubleshooting according to Problem Symptoms Table)
B
OK (When troubleshooting according to the DTC)
C



B
PROCEED TO NEXT SUSPECTED AREA SHOWN IN PROBLEM SYMPTOMS TABLE (Click here)

C
REPLACE AIR CONDITIONING AMPLIFIER ASSEMBLY (Click here)
A


3.PERFORM ACTIVE TEST USING INTELLIGENT TESTER
  1. Connect the intelligent tester to the DLC3.

  1. Turn the ignition switch to ON.

  1. Turn the intelligent tester on.

  1. Enter the following menus: Body / Air Conditioner / Active Test.

  1. Check the operation by referring to the table below.


Air Conditioner 
Tester Display
Test Part
Control Range
Diagnostic Note
Air Mix Servo Targ Pulse(D)
No. 2 air conditioning radiator damper servo sub-assembly (air mix for driver side) pulse
Min.: 0, Max.: 255
Operates between 5 and 103 pulses

OK:
Air temperature changes in accordance with each control range.



NG
Go to step 4
OK

REPLACE AIR CONDITIONING AMPLIFIER ASSEMBLY (Click here)  

4.REPLACE NO. 2 AIR CONDITIONING RADIATOR DAMPER SERVO SUB-ASSEMBLY (AIR MIX FOR DRIVER SIDE)
  1. Replace the No. 2 air conditioning radiator damper servo sub-assembly (air mix for driver side) (Click here).

    HINT:
    Since the servo motor cannot be inspected while it is removed from the vehicle, replace the servo motor with a new or known good one and check that the condition returns to normal.

  1. Check for the DTC.

    Result:
    Result
    Proceed to
    DTC B1446/46 is output
    A
    DTC B1446/46 is not output
    B



B
END (NO. 2 AIR CONDITIONING RADIATOR DAMPER SERVO SUB-ASSEMBLY (AIR MIX FOR DRIVER SIDE) WAS DEFECTIVE)
A


5.REPLACE AIR CONDITIONING HARNESS ASSEMBLY
  1. Replace the air conditioning harness assembly (Click here).

    HINT:
    Since the air conditioning harness assembly cannot be inspected while it is removed from the vehicle, replace the air conditioning harness assembly with a new or known good one and check that the condition returns to normal.

  1. Check for the DTC.

    Result:
    Result
    Proceed to
    DTC B1446/46 is output
    A
    DTC B1446/46 is not output
    B



B
END (AIR CONDITIONING HARNESS ASSEMBLY WAS DEFECTIVE)
A

REPLACE AIR CONDITIONING AMPLIFIER ASSEMBLY (Click here)  

6.READ VALUE USING INTELLIGENT TESTER
  1. Connect the intelligent tester to the DLC3.

  1. Turn the ignition switch to ON.

  1. Turn the intelligent tester on.

  1. Operate the driver side temperature adjustment switch.

  1. Enter the following menus: Body / Air Conditioner / Data List.

  1. Check the value(s) by referring to the table below.


Air Conditioner 
Tester Display
Measurement Item/Range
Normal Condition
Diagnostic Note
Air Mix Servo Actual Pulse(D)
No. 1 air conditioning radiator damper servo sub-assembly (air mix for driver side) actual pulse / Min.: 0, Max.: 255
MAX COLD: 105
MAX HOT: 7
-

OK:
The display is as specified in the normal condition column.


Result:

Result
Proceed to
NG
A
OK (When troubleshooting according to Problem Symptoms Table)
B
OK (When troubleshooting according to the DTC)
C



B
PROCEED TO NEXT SUSPECTED AREA SHOWN IN PROBLEM SYMPTOMS TABLE (Click here)

C
REPLACE AIR CONDITIONING AMPLIFIER ASSEMBLY (Click here)
A


7.PERFORM ACTIVE TEST USING INTELLIGENT TESTER
  1. Connect the intelligent tester to the DLC3.

  1. Turn the ignition switch to ON.

  1. Turn the intelligent tester on.

  1. Enter the following menus: Body / Air Conditioner / Active Test.

  1. Check the operation by referring to the table below.


Air Conditioner 
Tester Display
Test Part
Control Range
Diagnostic Note
Air Mix Servo Targ Pulse(D)
No. 1 air conditioning radiator damper servo sub-assembly (air mix for driver side) pulse
Min.: 0, Max.: 255
Operates between 7 and 105 pulses

OK:
Air temperature changes in accordance with each control range.



NG
Go to step 8
OK

REPLACE AIR CONDITIONING AMPLIFIER ASSEMBLY (Click here)  

8.REPLACE NO. 1 AIR CONDITIONING RADIATOR DAMPER SERVO SUB-ASSEMBLY (AIR MIX FOR DRIVER SIDE)
  1. Replace the No. 1 air conditioning radiator damper servo sub-assembly (air mix for driver side) (Click here).

    HINT:
    Since the servo motor cannot be inspected while it is removed from the vehicle, replace the servo motor with a new or known good one and check that the condition returns to normal.

  1. Check for the DTC.

    Result:
    Result
    Proceed to
    DTC B1446/46 is output
    A
    DTC B1446/46 is not output
    B



B
END (NO. 1 AIR CONDITIONING RADIATOR DAMPER SERVO SUB-ASSEMBLY (AIR MIX FOR DRIVER SIDE) WAS DEFECTIVE)
A


9.REPLACE AIR CONDITIONING HARNESS ASSEMBLY
  1. Replace the air conditioning harness assembly (Click here).

    HINT:
    Since the air conditioning harness assembly cannot be inspected while it is removed from the vehicle, replace the air conditioning harness assembly with a new or known good one and check that the condition returns to normal.

  1. Check for the DTC.

    Result:
    Result
    Proceed to
    DTC B1446/46 is output
    A
    DTC B1446/46 is not output
    B



B
END (AIR CONDITIONING HARNESS ASSEMBLY WAS DEFECTIVE)
A

REPLACE AIR CONDITIONING AMPLIFIER ASSEMBLY (Click here)