Home › Engine / Hybrid System ยท 2GR-FE › ENGINE MECHANICAL › ENGINE UNIT

ENGINE UNIT > DISASSEMBLY

for Preparation Click here



1. REMOVE OIL FILLER CAP SUB-ASSEMBLY
  1. Remove the oil filler cap sub-assembly and oil filler gasket.



2. REMOVE SPARK PLUG


    A192460
  1. Remove the 6 spark plugs.



3. REMOVE OIL PAN DRAIN PLUG


    A129654
  1. Remove the oil pan drain plug and oil pan drain plug gasket.



4. REMOVE VENTILATION VALVE SUB-ASSEMBLY


    A129655
  1. Remove the ventilation valve sub-assembly.



5. REMOVE VVT SENSOR
  1. Disconnect the 4 sensor connectors.



    A173735E02
  1. Remove the 4 bolts and 4 sensors.
    Text in Illustration 
    *a
    for Bank 1
    *b
    for Bank 2
    *c
    for Intake Side
    *d
    for Exhaust Side



6. REMOVE CAMSHAFT TIMING OIL CONTROL VALVE ASSEMBLY
  1. Disconnect the 4 oil control valve connectors.



    A255500E01
  1. Remove the 4 bolts and 4 oil control valves.
    Text in Illustration 
    *a
    for Intake Side
    *b
    for Exhaust Side
    *c
    for Bank 2
    *d
    for Bank 1



    A090053E06
  1. Remove the O-ring from each oil control valve.
    Text in Illustration 
    *1
    O-ring



7. REMOVE CRANK POSITION SENSOR


    A191181
  1. Disconnect the crank position sensor connector.

  1. Remove the bolt and crank position sensor.



8. REMOVE NO. 1 OIL PIPE


    A135726E02
  1. Remove the 2 oil pipe unions, gaskets and No. 1 oil pipe.
    Text in Illustration 
    *1
    Oil Pipe Union

  1. Remove the oil control valve filter LH and gaskets.



9. REMOVE OIL PIPE


    A200607E04
  1. Remove the bolt.
    Text in Illustration 
    *1
    Oil Pipe Union
    *2
    Bolt

  1. Remove the 2 oil pipe unions and oil pipe.

  1. Remove the oil control valve filter RH and gaskets.



10. REMOVE TAPER SCREW PLUG


A292824

HINT:
Perform this operation only when a taper screw plug is installed.

  1. Remove the taper screw plug from the cylinder block.



11. REMOVE CYLINDER BLOCK WATER DRAIN COCK SUB-ASSEMBLY


  1. for Bank 1:

    1. Remove the cylinder block water drain cock sub-assembly from the cylinder block.



    2. A292825E01
    3. Remove the cylinder block water drain cock plug from the cylinder block water drain cock sub-assembly.
      Text in Illustration 
      *a
      for Bank 1
      *b
      for Bank 2

  1. for Bank 2:

    HINT:
    Perform this operation only when a taper screw plug is not installed.

  1. Remove the cylinder block water drain cock sub-assembly from the cylinder block.

  1. Remove the cylinder block water drain cock plugs from the cylinder block water drain cock sub-assembly.



12. REMOVE OIL FILTER CAP ASSEMBLY


    A204919E01
  1. Connect the hose with an inside diameter of 15 mm (0.591 in.) to the pipe.
    Text in Illustration 
    *1
    Pipe
    *2
    Hose



    A127997
  1. Remove the oil filter drain plug from the oil filter cap.



    A160741E02
  1. Insert the pipe with the hose into the oil filter cap.
    Text in Illustration 
    *1
    Cap
    *2
    O-ring
    *3
    Pipe

    NOTICE:
    Be sure to insert the pipe with the O-ring installed on the oil filter cap.

    HINT:
    Place the hose end into a container before draining oil from the hose.



    A127999
  1. Make sure that oil is completely drained, and remove the pipe and O-ring.

    HINT:
    Be sure to turn the pipe in the direction of the arrow to remove it.



    A128000E01
  1. Using SST, remove the oil filter cap.

    SST
    09228-06501  



    A128001E06
  1. Remove the oil filter element and O-ring from the oil filter cap.
    Text in Illustration 
    *1
    Oil Filter Element
    *2
    Oil Filter Cap
    *3
    O-ring

    NOTICE:
    Do not use any tools to remove the O-ring in order to prevent the cap from being damaged. Be sure to remove it by hand.



13. REMOVE CRANKSHAFT PULLEY


    A208600E03
  1. Using SST, loosen the crankshaft pulley bolt.

    SST
    09213-70011   (09213-70020)
    09330-00021  
    Text in Illustration 
    *a
    Hold
    V100135
    Turn



    A259943E01
  1. Using SST, remove the crankshaft pulley bolt and crankshaft pulley.

    SST
    09950-50013   (09951-05010, 09952-05010, 09953-05020, 09954-05021)
    Text in Illustration 
    *a
    Hold
    V100135
    Turn



    A205852
  1. Remove the pulley set key from the crankshaft.



14. REMOVE ENGINE OIL LEVEL DIPSTICK GUIDE


    A192400
  1. Remove the bolt and engine oil level dipstick guide.



    A171897
  1. Remove the O-ring.



15. REMOVE NO. 1 FRONT ENGINE MOUNTING BRACKET LH


    A129672
  1. Remove the 6 bolts and No. 1 front engine mounting bracket LH.

  1. Using an E8 "TORX" socket wrench, remove the 2 stud bolts.



16. REMOVE WATER INLET HOUSING


    A129673
  1. Remove the 2 nuts, water inlet and thermostat.

  1. Remove the gasket.

  1. Remove the 2 stud bolts.

  1. Separate the No. 1 water by-pass hose from the water inlet housing.



    A134879E04
  1. Remove the drain cock plug.
    Text in Illustration 
    *1
    Nut
    *2
    Bolt

  1. Remove the drain cock assembly.

  1. Remove the 2 bolts, nut, and water inlet housing.



    A129675
  1. Remove the 2 O-rings.



17. REMOVE WATER OUTLET


    A129676E02
  1. Remove the 2 bolts, 4 nuts and water outlet.
    Text in Illustration 
    *1
    Nut
    *2
    Bolt



    A129677
  1. Remove the 2 gaskets and O-ring.



18. REMOVE CYLINDER HEAD COVER SUB-ASSEMBLY


    A129679
  1. Remove the 12 bolts, seal washer, cylinder head cover sub-assembly and cylinder head cover gasket.



    A129699
  1. Remove the 3 gaskets.



19. REMOVE CYLINDER HEAD COVER SUB-ASSEMBLY LH


    A129678E05
  1. Remove the 12 bolts, seal washer, cylinder head cover sub-assembly LH and No. 2 cylinder head cover gasket.
    Text in Illustration 
    *1
    Baffle Plate

    NOTICE:
    The baffle plate is located on the back of the portion shown in the illustration. Do not damage the baffle plate when removing the cylinder head cover sub-assembly LH.



    A129705
  1. Remove the 3 gaskets.



20. REMOVE NO. 2 OIL PAN SUB-ASSEMBLY


    A129680E02
  1. Remove the 16 bolts and 2 nuts.
    Text in Illustration 
    *1
    Nut



    A120816
  1. Insert the blade of the oil pan seal cutter between the oil pans. Cut through the applied sealer and remove the No. 2 oil pan sub-assembly.

    NOTICE:
    Be careful not to damage the contact surfaces of the oil pans.

  1. Using an E6 "TORX" socket wrench, remove the 2 stud bolts.



21. REMOVE OIL STRAINER SUB-ASSEMBLY


    A129681E03
  1. Remove the bolt, 2 nuts, oil strainer sub-assembly and gasket.
    Text in Illustration 
    *1
    Bolt
    *2
    Nut

  1. Using an E6 "TORX" socket wrench, remove the 2 stud bolts.



22. REMOVE OIL PAN SUB-ASSEMBLY


    A129682E03
  1. Remove the 16 bolts and 2 nuts.
    Text in Illustration 
    *1
    Nut

    HINT:
    Be sure to clean the bolts and stud bolts, and check the threads for cracks or other damage.



    A129683E02
  1. Remove the oil pan sub-assembly by prying between the oil pan sub-assembly and cylinder block with a screwdriver.
    Text in Illustration 
    *1
    Protective Tape

    NOTICE:
    Be careful not to damage the contact surfaces of the cylinder block and oil pan sub-assembly.

    HINT:
    Tape the screwdriver tip before use.



    A129684
  1. Remove the 2 O-rings.

  1. Using an E8 "TORX" socket wrench, remove the 2 stud bolts.



23. REMOVE NO. 1 OIL PAN BAFFLE PLATE


    A129685
  1. Remove the 7 bolts and No. 1 oil pan baffle plate.



24. REMOVE ENGINE REAR OIL SEAL RETAINER


    A129686
  1. Remove the 6 bolts.



    A129687E02
  1. Using a screwdriver, pry out the engine rear oil seal retainer.
    Text in Illustration 
    *1
    Protective Tape
    V100135
    Pry

    NOTICE:
    Be careful not to damage the engine rear oil seal retainer.

    HINT:
    Tape the screwdriver tip before use.



25. REMOVE ENGINE REAR OIL SEAL


    A131834E07
  1. Place the engine rear oil seal retainer on wooden blocks.
    Text in Illustration 
    *1
    Protective Tape
    *2
    Wooden Block

  1. Using a screwdriver and a hammer, tap out the engine rear oil seal.

    NOTICE:
    Be careful not to damage the engine rear oil seal retainer.

    HINT:
    Tape the screwdriver tip before use.



26. REMOVE ENGINE WATER PUMP ASSEMBLY


    A129688
  1. Remove the 16 bolts, engine water pump assembly and water pump gasket.



27. REMOVE TIMING CHAIN COVER SUB-ASSEMBLY


    A129689E02
  1. Remove the 15 bolts and 2 nuts as shown in the illustration.
    Text in Illustration 
    *1
    Nut



    A129690E04
  1. Remove the timing chain cover sub-assembly by prying between the timing chain cover sub-assembly and cylinder head sub-assembly or cylinder block with a screwdriver.
    Text in Illustration 
    *1
    Protective Tape

    NOTICE:
    Be careful not to damage the contact surfaces of the cylinder head sub-assembly, cylinder block and timing chain cover sub-assembly.

    HINT:
    Tape the screwdriver tip before use.

  1. Remove the 4 bolts, timing chain cover plate and timing chain cover plate gasket.



    A128006
  1. Remove the gasket.



28. REMOVE TIMING CHAIN CASE OIL SEAL


    A128007E05
  1. Using a screwdriver and wooden block, pry out the oil seal.
    Text in Illustration 
    *1
    Protective Tape
    *2
    Wooden Block

    HINT:
    Tape the screwdriver tip before use.



29. SET NO. 1 CYLINDER TO TDC/COMPRESSION
  1. Temporarily tighten the pulley set bolt.



    A205165E02
  1. Turn the crankshaft clockwise to align the timing mark on the crank angle sensor plate with the RH block bore center line (TDC/compression).
    Text in Illustration 
    *1
    Sensor Plate
    *a
    Center Line
    *b
    Timing Mark



    A129692E07
  1. Check that the timing marks of the camshaft timing gear assembly and camshaft timing exhaust gear assembly are aligned with the timing marks of the camshaft bearing caps as shown in the illustration.
    Text in Illustration 
    *a
    Timing Mark
    If not, turn the crankshaft clockwise 1 revolution (360°) and align the timing marks as above.



30. REMOVE NO. 1 CHAIN TENSIONER ASSEMBLY


    A124589E06
  1. Move the stopper plate upward to release the lock, and push the plunger deep into the No. 1 chain tensioner assembly.
    Text in Illustration 
    *1
    Plunger
    *2
    Stopper Plate
    *3
    Pin

  1. Move the stopper plate downward to set the lock, and insert a pin of 1.27 mm diameter (0.0500 in.) into the stopper plate hole.



    A095165
  1. Remove the 2 bolts and No. 1 chain tensioner assembly.



31. REMOVE CHAIN TENSIONER SLIPPER
  1. Remove the chain tensioner slipper.



32. REMOVE CHAIN SUB-ASSEMBLY


    A211711E02
  1. Turn the crankshaft counterclockwise 10° to loosen the chain of the crankshaft timing sprocket.
    Text in Illustration 
    *1
    Sensor Plate
    *a
    Center Line
    *b
    Timing Mark

  1. Remove the pulley set bolt.



    A134890
  1. Remove the chain sub-assembly from the crankshaft timing sprocket and place it on the crankshaft.



    A095682E13
  1. Turn the camshaft timing gear assembly on bank 1 clockwise (approximately 60°) and set it as shown in the illustration. Be sure to loosen the chain sub-assembly between the banks.
    Text in Illustration 
    *a
    for Bank 1

  1. Remove the chain sub-assembly.



33. REMOVE IDLE SPROCKET ASSEMBLY


    A129695
  1. Using a 10 mm hexagon wrench, remove the No. 2 idle gear shaft, idle sprocket assembly and No. 1 idle gear shaft.



34. REMOVE NO. 1 CHAIN VIBRATION DAMPER


    A129696
  1. Remove the 2 bolts and No. 1 chain vibration damper.



35. REMOVE NO. 2 CHAIN VIBRATION DAMPER
  1. Remove the 2 No. 2 chain vibration dampers.



36. REMOVE CRANKSHAFT TIMING SPROCKET


    A109720
  1. Remove the crankshaft timing sprocket from the crankshaft.

  1. Remove the 2 keys from the crankshaft.



37. REMOVE CAMSHAFT TIMING GEARS AND NO. 2 CHAIN (for Bank 1)


    A120651E08
  1. While raising the No. 2 chain tensioner assembly, insert a pin of 1.0 mm (0.0394 in.) diameter into the hole to hold the No. 2 chain tensioner assembly.
    Text in Illustration 
    *1
    Pin
    *2
    Plunger
    *a
    Push



    A182777E06
  1. Using SST to hold the hexagonal portion of each camshaft, loosen the flange bolts of the camshaft timing gear assembly and the camshaft timing exhaust gear assembly.
    Text in Illustration 
    *a
    Turn
    *b
    Hold

    SST
    09922-10010  

    NOTICE:
    1. Be careful not to damage the cylinder head with SST.
    2. Do not loosen the other bolts. If any of the bolts is loosened, replace the camshaft timing gear assembly and/or the camshaft timing exhaust gear assembly with a new one.

  1. Remove the 2 bolts and the camshaft timing gear assembly together with the No. 2 chain.



38. REMOVE NO. 2 CHAIN TENSIONER ASSEMBLY


    A109721
  1. Remove the bolt and No. 2 chain tensioner assembly.



39. REMOVE CAMSHAFT BEARING CAP (for Bank 1)


    A129700E08
  1. Check that the camshafts are positioned as shown in the illustration.
    Text in Illustration 
    *1
    Knock Pin
    *a
    Front View



    A129701E03
  1. Uniformly loosen and remove the 8 bearing cap bolts in several steps and in the sequence shown in the illustration.



    A129702E01
  1. Uniformly loosen and remove the 12 bearing cap bolts in several steps and in the sequence shown in the illustration.

    NOTICE:
    Uniformly loosen the bolts while keeping the camshaft level.

  1. Remove the 5 camshaft bearing caps.



40. REMOVE CAMSHAFT
  1. Remove the camshaft.



41. REMOVE NO. 2 CAMSHAFT
  1. Remove the No. 2 camshaft.



42. REMOVE CAMSHAFT HOUSING SUB-ASSEMBLY RH


    A129703E02
  1. Remove the camshaft housing sub-assembly RH by prying between the cylinder head and camshaft housing sub-assembly RH with a screwdriver.
    Text in Illustration 
    *1
    Protective Tape

    NOTICE:
    Be careful not to damage the contact surfaces of the cylinder head and camshaft housing sub-assembly RH.

    HINT:
    Tape the screwdriver tip before use.



43. REMOVE CAMSHAFT TIMING GEARS AND NO. 2 CHAIN (for Bank 2)


    A120657E07
  1. While pushing down the No. 3 chain tensioner assembly, insert a pin of 1.0 mm (0.0394 in.) diameter into the hole to hold the No. 3 chain tensioner assembly.
    Text in Illustration 
    *1
    Pin
    *2
    Plunger
    *a
    Push



    A182778E06
  1. Using SST to hold the hexagonal portion of each camshaft, loosen the flange bolts of the camshaft timing gear assembly and the camshaft timing exhaust gear assembly.
    Text in Illustration 
    *a
    Turn
    *b
    Hold

    SST
    09922-10010  

    NOTICE:
    1. Be careful not to damage the cylinder head with SST.
    2. Do not loosen the other bolts. If any of the bolts is loosened, replace the camshaft timing gear assembly and/or the camshaft timing exhaust gear assembly with a new one.

  1. Remove the 2 bolts and the camshaft timing gear together with the No. 2 chain.



44. REMOVE NO. 3 CHAIN TENSIONER ASSEMBLY


    A109722
  1. Remove the bolt and No. 3 chain tensioner assembly.



45. REMOVE CAMSHAFT BEARING CAP (for Bank 2)


    A129706E06
  1. Check that the camshafts are positioned as shown in the illustration.
    Text in Illustration 
    *1
    Knock Pin
    *a
    Front View



    A134891E03
  1. Uniformly loosen and remove the 8 bearing cap bolts in several steps and in the sequence shown in the illustration.



    A129708E01
  1. Uniformly loosen and remove the 13 bearing cap bolts in several steps and in the sequence shown in the illustration.

    NOTICE:
    Uniformly loosen the bolts while keeping the camshaft level.

  1. Remove the 5 camshaft bearing caps.



46. REMOVE NO. 3 CAMSHAFT
  1. Remove the No. 3 camshaft.



47. REMOVE NO. 4 CAMSHAFT
  1. Remove the No. 4 camshaft.



48. REMOVE CAMSHAFT HOUSING SUB-ASSEMBLY LH


    A129709E02
  1. Remove the camshaft housing sub-assembly LH by prying between the cylinder head and camshaft housing sub-assembly LH with a screwdriver.
    Text in Illustration 
    *1
    Protective Tape

    NOTICE:
    Be careful not to damage the contact surfaces of the cylinder head and camshaft housing sub-assembly LH.

    HINT:
    Tape the screwdriver tip before use.



49. REMOVE NO. 1 VALVE ROCKER ARM SUB-ASSEMBLY
  1. Remove the 24 valve rocker arms.

    HINT:
    Arrange the removed parts in the correct order.



50. REMOVE VALVE LASH ADJUSTER ASSEMBLY
  1. Remove the 24 valve lash adjuster assemblies from the cylinder head.

    HINT:
    Arrange the removed parts in the correct order.



51. REMOVE VALVE STEM CAP
  1. Remove the 24 valve stem caps.



52. REMOVE CYLINDER HEAD SUB-ASSEMBLY RH


    A129712E01
  1. Using a 10 mm bi-hexagon wrench, uniformly loosen the 8 cylinder head bolts in the sequence shown in the illustration. Remove the 8 cylinder head bolts and plate washers.

    NOTICE:
    1. Be careful not to drop washers into the cylinder head sub-assembly.
    2. Cylinder head warpage or cracking could result from removing bolts in the incorrect order.

    HINT:
    Arrange the removed parts in the correct order.

  1. Remove the cylinder head sub-assembly RH.



53. REMOVE CYLINDER HEAD GASKET RH
  1. Remove the cylinder head gasket RH.



54. REMOVE CYLINDER HEAD SUB-ASSEMBLY LH


    A129710E01
  1. Uniformly loosen and remove the 2 cylinder head set bolts in several steps and in the sequence shown in the illustration.



    A129711E01
  1. Using a 10 mm bi-hexagon wrench, uniformly loosen the 8 bolts in the sequence shown in the illustration. Remove the 8 cylinder head bolts and plate washers.

    NOTICE:
    1. Be careful not to drop washers into the cylinder head sub-assembly.
    2. Cylinder head warpage or cracking could result from removing bolts in the incorrect order.

    HINT:
    Be sure to keep separate the removed parts for each installation position.

  1. Remove the cylinder head sub-assembly LH.



55. REMOVE CYLINDER HEAD GASKET LH
  1. Remove the cylinder head gasket LH.



56. REMOVE WATER INLET PIPE
  1. Remove the 2 clamps and separate the No. 1 water by-pass hose.



    A129713
  1. Remove the 2 bolts and water inlet pipe.