Home › Engine / Hybrid System ยท 2GR-FE › ENGINE MECHANICAL › CYLINDER HEAD

CYLINDER HEAD > REPLACEMENT

for Preparation Click here



1. REPLACE INTAKE VALVE GUIDE BUSH
  1. Heat the cylinder head to 80 to 100°C (176 to 212°F).

  1. Place the cylinder head on wooden blocks.



    A121839E03
  1. Using SST and a hammer, tap out the intake valve guide bushes.

    SST
    09201-10000   (09201-01050)
    09950-70010   (09951-07100)



    A109626
  1. Using a caliper gauge, measure the intake valve guide bush bore diameter of the cylinder head.

    Cylinder bore diameter:
    10.285 to 10.306 mm (0.4049 to 0.4057 in.)

    Select a new guide bush (STD or O/S 0.05):
    Bush Size
    Bush Bore Diameter
    STD
    10.333 to 10.344 mm (0.4068 to 0.4072 in.)
    O/S 0.05
    10.383 to 10.394 mm (0.4088 to 0.4092 in.)

    If the bush bore diameter of the cylinder head is greater than 10.306 mm (0.4057 in.), machine the bush bore to the dimension of 10.335 to 10.356 mm (0.4069 to 0.4077 in.) to install an O/S 0.05 valve guide bush.
    If the bush bore diameter of the cylinder head is greater than 10.356 mm (0.4077 in.), replace the cylinder head.

  1. Heat the cylinder head to 80 to 100°C (176 to 212°F).

  1. Place the cylinder head on wooden blocks.



    A120710E06
  1. Using SST, tap in new intake valve guide bushes to the specified protrusion height.
    Text in Illustration 
    *a
    Protrusion Height

    SST
    09201-10000   (09201-01050)
    09950-70010   (09951-07100)

    Protrusion height:
    9.30 to 9.70 mm (0.3661 to 0.3819 in.)



    A131839
  1. Using a sharp 5.5 mm reamer, ream the valve guide bushings to obtain the specified clearance.

    Standard oil clearance:
    0.025 to 0.060 mm (0.000984 to 0.00236 in.)



2. REPLACE EXHAUST VALVE GUIDE BUSH
  1. Heat the cylinder head to 80 to 100°C (176 to 212°F).

  1. Place the cylinder head on wooden blocks.

  1. Using SST and a hammer, tap out the exhaust valve guide bushes.

    SST
    09201-10000   (09201-01050)
    09950-70010   (09951-07100)



    A109628
  1. Using a caliper gauge, measure the exhaust valve guide bush bore diameter of the cylinder head.

    Cylinder bore diameter:
    10.285 to 10.306 mm (0.4049 to 0.4057 in.)

    Select a new guide bush (STD or O/S 0.05):
    Bush Size
    Bush Bore Diameter
    STD
    10.333 to 10.344 mm (0.4068 to 0.4072 in.)
    O/S 0.05
    10.383 to 10.394 mm (0.4088 to 0.4092 in.)

    If the bush bore diameter of the cylinder head is greater than 10.306 mm (0.4057 in.), machine the bush bore to the dimension of 10.335 to 10.356 mm (0.4069 to 0.4077 in.) to install an O/S 0.05 valve guide bush.
    If the bush bore diameter of the cylinder head is greater than 10.356 mm (0.4077 in.), replace the cylinder head.

  1. Heat the cylinder head to 80 to 100°C (176 to 212°F).

  1. Place the cylinder head on wooden blocks.



    A120712E07
  1. Using SST, tap in new exhaust valve guide bushes to the specified protrusion height.
    Text in Illustration 
    *a
    Protrusion Height

    SST
    09201-10000   (09201-01050)
    09950-70010   (09951-07100)

    Protrusion height:
    9.30 to 9.70 mm (0.3661 to 0.3819 in.)



    A096429
  1. Using a sharp 5.5 mm reamer, ream the valve guide bushings to obtain the specified clearance.

    Standard oil clearance:
    0.030 to 0.065 mm (0.00118 to 0.00256 in.)



3. REPLACE RING PIN

NOTICE:
It is not necessary to remove the ring pin unless it is being replaced.



    A131888E08
  1. Using a plastic hammer, tap in new ring pins to the specified protrusion height.
    Text in Illustration 
    *a
    for Bank 1
    *b
    for Bank 2

    Specified protrusion height:
    2.5 to 3.5 mm (0.0984 to 0.138 in.)



4. REPLACE STUD BOLT

NOTICE:
If a stud bolt is deformed or the threads are damaged, replace it.



  1. Using an E6 and E8 "TORX" socket wrench, install the stud bolts.


    A238938E02


    Text in Illustration 
    *a
    Bank 1 Rear Side
    *b
    Bank 1 Intake Side
    *c
    Bank 2 Intake Side
    *d
    Bank 1 Exhaust Side
    *e
    Bank 2 Exhaust Side
    *f
    Bank 2 Rear Side

    Torque:
    Bolts A:
    10 N*m{ 102 kgf*cm , 7 ft.*lbf }
    Bolt B:
    4.0 N*m{ 41 kgf*cm , 35 in.*lbf }



5. REPLACE STRAIGHT PIN

NOTICE:
If a straight pin is deformed, replace it.



  1. Using a plastic hammer, tap in new straight pins as shown in the illustration.


    A131890E09


    Text in Illustration 
    *a
    for Bank 1
    *b
    for Bank 2

    Protrusion height:
    17.5 to 19.5 mm (0.689 to 0.768 in.)