REAR AIRBAG SENSOR > REMOVAL |
| 1. PRECAUTION |
| 2. DISCONNECT CABLE FROM NEGATIVE BATTERY TERMINAL |
| 3. REMOVE REAR SEAT CUSHION ASSEMBLY (for Fold Down Seat Type) |
![]() |
Disengage the hook of the seat cushion from the vehicle body as shown in the illustration.
| a | 100 mm (3.94 in.) or less |
Choose a hook to disengage first. Place your hands near the hook as shown in the illustration. Then lift the seat cushion to disengage the hook.
Repeat the step above for the other hook.
Remove the rear seat cushion assembly.
| 4. REMOVE REAR SEAT CUSHION LOCK HOOK (for Fold Down Seat Type) |
![]() |
Disengage the claw and remove the rear seat cushion lock hook.
| 5. REMOVE REAR SIDE SEATBACK ASSEMBLY (for Fold Down Seat Type) |
Disconnect the rear seat outer belt from the rear seat shoulder belt guide LH.
![]() |
Remove the bolt.
Disengage the hook and remove the rear side seatback assembly LH.
| 6. REMOVE REAR SEAT CUSHION ASSEMBLY (for Reclining Seat Type) |
![]() |
Disengage the hook of the seat cushion from the vehicle body as shown in the illustration.
| a | 100 mm (3.94 in.) or less |
Choose a hook to detach first. Place your hands near the hook as shown in the illustration. Then lift the seat cushion to detach the hook.
Repeat the step above for the other hook.
w/ Seat Heater System:
Disconnect the 2 seat heater connectors.
Remove the rear seat cushion assembly.
| 7. REMOVE REAR SEAT CUSHION LOCK HOOK (for Reclining Seat Type) |
![]() |
Disengage the claw and remove the rear seat cushion lock hook.
| 8. REMOVE REAR SEAT HEADREST ASSEMBLY (for Reclining Seat Type) |
| 9. REMOVE REAR SEATBACK COVER (for Reclining Seat Type) |
![]() |
Disengage the 4 claws and remove the 2 rear seatback covers.
| 10. REMOVE REAR SEATBACK ASSEMBLY (for Reclining Seat Type) |
w/ Rear Seat Side Airbag:
Disconnect each connector and clamp from the child restraint seat anchor bracket sub-assembly LH.
Disengage the 2 rear seat belts from the 2 rear seat shoulder belt guides.
![]() |
Disengage the 2 hooks and disconnect the cover.
Remove the 2 nuts, 2 bolts and rear seatback assembly LH.
| 11. REMOVE REAR DOOR SCUFF PLATE (for Reclining Seat Type) |
![]() |
Disengage the 6 claws and remove the rear door scuff plate LH.
| 12. DISCONNECT REAR DOOR OPENING TRIM WEATHERSTRIP (for Reclining Seat Type) |
| 13. REMOVE REAR SEAT SIDE GARNISH (for Reclining Seat Type) |
![]() |
Remove the bolt.
Disengage the claw, 2 clips and guide and remove the rear seat side garnish LH.
| 14. REMOVE SIDE NO. 2 AIRBAG SENSOR ASSEMBLY |
Check that the ignition switch is off.
Check that the cable is disconnected from the negative (-) battery terminal.
Disconnect the connector from the side No. 2 airbag sensor assembly.
Push down the white housing lock and slide the yellow CPA. (At this time, the connector cannot be disconnected yet.)

| *1 | White Housing Lock | *2 | Yellow CPA |
| *a | Connector Lock is Released | - | - |
Push down the white housing lock again and disconnect the connector.
![]() |
Remove the bolt and side No. 2 airbag sensor assembly from the vehicle body.
After disconnecting the connector, check that the position of the white housing lock is correct as shown in the illustration.

| *a | Incorrect | *b | Correct |