Home › Vehicle Exterior › SLIDING ROOF / CONVERTIBLE › SLIDING ROOF SYSTEM

SLIDING ROOF SYSTEM > DATA LIST / ACTIVE TEST

for Preparation Click here



READ DATA LIST

HINT:
Using the intelligent tester to read the Data List allows the values or states of switches, sensors, actuators and other items to be read without removing any parts. This non-intrusive inspection can be very useful because intermittent conditions or signals may be discovered before parts or wiring is disturbed. Reading the Data List information early in troubleshooting is one way to save diagnostic time.

NOTICE:
In the following table, the values listed under "Normal Condition" are reference values. Do not depend solely on these reference values when deciding whether a part is faulty or not.

  1. Connect the intelligent tester to the DLC3.

  2. Turn the ignition switch to ON.

  3. Turn the intelligent tester on.

  4. Enter the following menus: Body / Sliding Roof or Main Body / Data List.

  5. Read the Data List according to the display on the intelligent tester.

    Sliding Roof (Sliding Roof ECU (Sliding Roof Drive Gear Sub-assembly)) 
    Tester Display
    Measurement Item/Range
    Normal Condition
    Diagnostic Note
    Open Switch
    OPEN switch signal/ON or OFF
    ON: OPEN switch pressed
    OFF: OPEN switch not pressed
    -
    Close Switch
    CLOSE switch signal/ON or OFF
    ON: CLOSE switch pressed
    OFF: CLOSE switch not pressed
    -
    Up Switch
    UP switch signal/ON or OFF
    ON: UP switch pressed
    OFF: UP switch not pressed
    -
    Down Switch
    DOWN switch signal/ON or OFF
    ON: DOWN switch pressed
    OFF: DOWN switch not pressed
    -
    Front SW Auto Operation
    Sliding roof auto function/ON or OFF
    Customization status displayed
    -
    Hall IC1 Pulse
    Hall IC1 pulse output/Lo or Hi
    Lo and Hi repeat during motor operation
    Lo: Hall IC1 output is low
    Hi: Hall IC1 output is high
    Hall IC1 Status
    Status of Hall IC1/Normal or Error
    Normal: Hall IC1 normal
    Error: Hall IC1 not normal
    -
    Hall IC2 Pulse
    Hall IC2 pulse output/Lo or Hi
    Lo and Hi repeat during motor operation
    Lo: Hall IC2 output is low
    Hi: Hall IC2 output is high
    Hall IC2 Status
    Status of Hall IC2/Normal or Error
    Normal: Hall IC2 normal
    Error: Hall IC2 not normal
    -
    Ignition (Direct Signal)
    Ignition switch signal/ON or OFF
    ON: Ignition switch ON
    OFF: Ignition switch off
    -
    Ignition (MPX)
    Ignition switch signal (LIN signal)/ON or OFF
    ON: Ignition switch ON
    OFF: Ignition switch off
    -
    Door Courtesy
    Driver door courtesy light switch signal/ON or OFF
    ON: Driver door open
    OFF: Driver door closed
    -
    Door Key Close Operation
    Key-linked sliding roof close signal/ON or OFF
    ON: Turn and hold the driver door key cylinder to lock position
    OFF: Driver door key cylinder not turned
    -
    Door Key Open Operation
    Key-linked sliding roof open signal/ON or OFF
    ON: Turn and hold the driver door key cylinder to unlock position
    OFF: Driver door key cylinder not turned
    -
    Wireless Close Operation
    Wireless transmitter-linked sliding roof close signal/ON or OFF
    ON: Press and hold the transmitter LOCK switch
    OFF: Transmitter LOCK switch not pressed

    Wireless Open Operation
    Wireless transmitter-linked sliding roof open signal/ON or OFF
    ON: Press and hold the transmitter UNLOCK switch
    OFF: Transmitter UNLOCK switch not pressed
    -
    Key Off Permission
    Key-off sliding roof operation permit signal/ON or OFF
    ON: Front doors are not opened within 43 seconds after ignition switch turned off
    OFF: Any status except "ON" status
    -
    Door Key Related Operation
    Key-linked sliding roof open function operating direction/Slide or Tilt
    Customization status displayed
    -
    Wireless Key Rel Operation
    Wireless transmitter-linked sliding roof open function operating direction/Slide or Tilt
    Customization status displayed
    -
    Open Switch Failure(Past)
    Open switch failure signal (Past)/ON or OFF
    ON: Sliding roof open switch failure signal (Past)
    OFF: No sliding roof open switch failure signal (Past)
    -
    Close Switch Failure(Past)
    Close switch failure signal (Past)/ON or OFF
    ON: Sliding roof close switch failure signal (Past)
    OFF: No sliding roof close switch failure signal (Past)
    -
    Up Switch Failure(Past)
    Up switch failure signal (Past)/ON or OFF
    ON: Sliding roof tilt up switch failure signal (Past)
    OFF: No sliding roof tilt up switch failure signal (Past)
    -
    Down Switch Failure(Past)
    Down switch failure signal (Past)/ON or OFF
    ON: Sliding roof tilt down switch failure signal (Past)
    OFF: No sliding roof tilt down switch failure signal (Past)
    -
    Open Switch Failure(Current)
    Open switch failure signal (Current)/ON or OFF
    ON: Sliding roof open switch failure signal (Current)
    OFF: No sliding roof open switch failure signal (Current)
    -
    Close Switch Failure(Current)
    Close switch failure signal (Current)/ON or OFF
    ON: Sliding roof close switch failure signal (Current)
    OFF: No sliding roof close switch failure signal (Current)
    -
    Up Switch Failure(Current)
    Up switch failure signal (Current)/ON or OFF
    ON: Sliding roof tilt up switch failure signal (Current)
    OFF: No sliding roof tilt up switch failure signal (Current)
    -
    Down Switch Failure(Current)
    Down switch failure signal (Current)/ON or OFF
    ON: Sliding roof tilt down switch failure signal (Current)
    OFF: No sliding roof tilt down switch failure signal (Current)
    -
    Number of Trouble Codes
    Number of DTCs / Min.: 0, Max.: 255
    Number of stored DTCs
    -

    Main Body (Main Body ECU (Multiplex Network Body ECU)) 
    Tester Display
    Measurement Item/Range
    Normal Condition
    Diagnostic Note
    Door Key P/W Up
    Door key linked sliding roof close/ON or OFF
    Customization status displayed
    -
    Door Key P/W Down
    Door key linked sliding roof open/ON or OFF
    Customization status displayed
    -
    P/W Up W/Transmit
    Wireless transmitter linked sliding roof close/ON or OFF
    Customization status displayed
    -
    P/W Down W/Transmit
    Wireless transmitter linked sliding roof open/ON or OFF
    Customization status displayed
    -
    Slide Roof Open Warning
    Sliding roof open warning/ON or OFF
    Customization status displayed
    -


PERFORM ACTIVE TEST

HINT:
Using the intelligent tester to perform Active Tests allows relays, VSVs, actuators and other items to be operated without removing any parts. This non-intrusive functional inspection can be very useful because intermittent operation may be discovered before parts or wiring is disturbed. Performing Active Tests early in troubleshooting is one way to save diagnostic time. Data List information can be displayed while performing Active Tests.

  1. Connect the intelligent tester to the DLC3.

  2. Turn the ignition switch to ON.

  3. Turn the intelligent tester on.

  4. Enter the following menus: Body / Sliding Roof / Active Test.

  5. Perform the Active Test according to the display on the intelligent tester.

    Sliding Roof (Sliding Roof ECU (Sliding Roof Drive Gear Sub-assembly)) 
    Tester Display
    Test Part
    Control Range
    Diagnostic Note
    Slide Roof
    Operate sliding roof motor
    OFF / Opn/Dwn / Clos/Up
    -