Home › Vehicle Interior › HEATING / AIR CONDITIONING › AIR CONDITIONING SYSTEM

DTC    B1451/51    Compressor Solenoid Circuit

for Preparation Click here


DESCRIPTION

  1. 1. for 2AR-FE
    In this circuit, the compressor assembly with pulley (compressor solenoid) receives a refrigerant compression demand signal from the air conditioning amplifier assembly.
    Based on this signal, the compressor assembly with pulley (compressor solenoid) changes the amount of compressor output.
  1. 2. for 2GR-FE
    In this circuit, the cooler compressor assembly (compressor solenoid) receives a refrigerant compression demand signal from the air conditioning amplifier assembly.
    Based on this signal, the cooler compressor assembly (compressor solenoid) changes the amount of compressor output.

DTC No.
DTC Detection Condition
Trouble Area
B1451/51
Open or short in compressor solenoid circuit
  1. Compressor assembly with pulley (compressor solenoid)*1
  2. Cooler compressor assembly (compressor solenoid)*2
  3. Harness or connector between air conditioning amplifier assembly and compressor assembly with pulley (compressor solenoid)*1
  4. Harness or connector between air conditioning amplifier assembly and cooler compressor assembly (compressor solenoid)*2
  5. Air conditioning amplifier assembly
  1. *1: for 2AR-FE
  2. *2: for 2GR-FE

WIRING DIAGRAM


E229254E12


INSPECTION PROCEDURE

1.CONFIRM MODEL

Result:
Result
Proceed to
for 2AR-FE
A
for 2GR-FE
B



B
Go to step 5
A


2.INSPECT COMPRESSOR ASSEMBLY WITH PULLEY (COMPRESSOR SOLENOID)


    E229635E01
  1. Disconnect the E74 compressor assembly with pulley (compressor solenoid) connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    E74-2 (SOL+) - E74-1 (SOL-)
    20°C (68°F)
    10 to 11 Ω

    Text in Illustration 
    *a
    Component without harness connected
    (Compressor Assembly with Pulley (Compressor Solenoid))



NG
REPLACE COMPRESSOR ASSEMBLY WITH PULLEY (Click here)
OK


3.CHECK HARNESS AND CONNECTOR (COMPRESSOR ASSEMBLY WITH PULLEY (COMPRESSOR SOLENOID) - BODY GROUND)
  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    E74-1 (SOL-) - Body ground
    Always
    Below 1 Ω



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK


4.CHECK HARNESS AND CONNECTOR (COMPRESSOR ASSEMBLY WITH PULLEY (COMPRESSOR SOLENOID)- AIR CONDITIONING AMPLIFIER ASSEMBLY)
  1. Disconnect the I77 air conditioning amplifier assembly connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    I77-2 (SOL+) - E74-2 (SOL+)
    Always
    Below 1 Ω
    I77-2 (SOL+) - Body ground
    Always
    10 kΩ or higher

    Result:
    Result
    Proceed to
    NG
    A
    OK (When troubleshooting according to Problem Symptoms Table)
    B
    OK (When troubleshooting according to the DTC)
    C



B
PROCEED TO NEXT SUSPECTED AREA SHOWN IN PROBLEM SYMPTOMS TABLE (Click here)

C
REPLACE AIR CONDITIONING AMPLIFIER ASSEMBLY (Click here)
A

REPAIR OR REPLACE HARNESS OR CONNECTOR 

5.INSPECT COOLER COMPRESSOR ASSEMBLY (COMPRESSOR SOLENOID)


    E229635E01
  1. Disconnect the E74 cooler compressor assembly (compressor solenoid) connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    E74-2 (SOL+) - E74-1 (SOL-)
    20°C (68°F)
    10 to 11 Ω

    Text in Illustration 
    *a
    Component without harness connected
    (Cooler Compressor Assembly (Compressor Solenoid))



NG
REPLACE COOLER COMPRESSOR ASSEMBLY (Click here)
OK


6.CHECK HARNESS AND CONNECTOR (COOLER COMPRESSOR ASSEMBLY (COMPRESSOR SOLENOID) - BODY GROUND)
  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    E74-1 (SOL-) - Body ground
    Always
    Below 1 Ω



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK


7.CHECK HARNESS AND CONNECTOR (COOLER COMPRESSOR ASSEMBLY (COMPRESSOR SOLENOID) - AIR CONDITIONING AMPLIFIER ASSEMBLY)
  1. Disconnect the I77 air conditioning amplifier assembly connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    I77-2 (SOL+) - E74-2 (SOL+)
    Always
    Below 1 Ω
    I77-2 (SOL+) - Body ground
    Always
    10 kΩ or higher

    Result:
    Result
    Proceed to
    NG
    A
    OK (When troubleshooting according to Problem Symptoms Table)
    B
    OK (When troubleshooting according to the DTC)
    C



B
PROCEED TO NEXT SUSPECTED AREA SHOWN IN PROBLEM SYMPTOMS TABLE (Click here)

C
REPLACE AIR CONDITIONING AMPLIFIER ASSEMBLY (Click here)
A

REPAIR OR REPLACE HARNESS OR CONNECTOR