Home › Engine / Hybrid System · 1AZ-FE › FUEL › FUEL INJECTOR

FUEL INJECTOR > INSPECTION

for Preparation Click here



1. INSPECT FUEL INJECTOR ASSEMBLY
  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    1 - 2
    20°C (68°F)
    11.6 to 12.4 Ω

    If the result is not as specified, replace the fuel injector assembly.



  1. Inspect the injector injection volume.

    CAUTION:
    Keep the fuel injector assembly away from sparks during the test.




      A264971E01
    1. Connect SST (fuel tube connector) to SST (hose) with SST (hose band), and then connect them to the fuel pipe (vehicle side).
      Text in Illustration 
      *1
      SST
      (Hose)
      *2
      SST
      (Hose Band)
      *3
      SST
      (Fuel Tube Connector)
      *4
      Fuel Pipe (Vehicle Side)

      SST
      09268-31014   (09268-41500, 09268-41700, 95336-08070)



    2. A264972E01
    3. Install a new O-ring to the fuel injector assembly.
      Text in Illustration 
      *1
      SST
      (Hose)
      *2
      SST
      (Hose Band)
      *3
      SST
      (Adapter)
      *4
      O-ring
      *5
      SST
      (Clamp)
      *6
      Vinyl Tube

      SST
      09268-31014   (09268-41110, 09268-41300, 09268-41700, 95336-08070)

    4. Connect SST (adapter and hose) to the fuel injector assembly, and hold the fuel injector assembly and union with SST (clamp).

    5. Install a vinyl tube onto the fuel injector assembly.

      CAUTION:
      Install a suitable vinyl tube onto the fuel injector assembly to contain any fuel spray.



    6. A264974E01
    7. Tie SST (clamp and adapter) together with SST (tie band) as shown in the illustration.
      Text in Illustration 
      *1
      SST
      (Tie Band)
      *2
      SST
      (Adapter)
      *3
      SST
      (Clamp)

      SST
      09268-31014   (09268-41110, 09268-41300, 09268-41800)

    8. Put the fuel injector assembly into a graduated cylinder.

    9. Operate the fuel pump .



    10. A264973E01
    11. Connect SST (wire) to the fuel injector assembly and the battery for 15 seconds, and measure the injection volume with the graduated cylinder. Test each fuel injector assembly 2 or 3 times.
      Text in Illustration 
      *1
      SST
      (Wire)
      *a
      Connect

      SST
      09842-30080  

      NOTICE:
      Always switch the voltage on and off at the battery side, not the fuel injector assembly side.

      Standard Injection Volume:
      Tester Connection
      Condition
      Specified Condition
      Positive terminal - Ground terminal
      Per 15 seconds
      76 to 92 cc (4.6 to 5.6 cu. in.)

      Difference between each fuel injector assembly:
      16 cc (1.0 cu. in.) or less

      If the result is not as specified, replace the fuel injector assembly.

  1. Check for fuel drop.

    1. In the condition above, disconnect the tester probes of SST (wire) from the battery and check for fuel drop from the fuel injector assembly.

      Standard fuel drop:
      1 drop or less per 12 minutes

      If fuel drop is not as specified, replace the fuel injector assembly.