DTC P0705 Transmission Range Sensor Circuit Malfunction (PRNDL Input) |
| DTC No. | DTC Detection Condition | Trouble Area |
| P0705 | (A) Any 2 or more signals of the following are ON simultaneously (2-trip detection logic)
|
|

| Tester Display | Measurement Item / Range | Normal Condition | Diagnostic Note |
| Neutral Position SW Signal | PNP switch status / ON or OFF |
| When the shift lever position displayed on the intelligent tester differs from the actual position, adjustment of the PNP switch or the shift cable may be incorrect. |
| Shift SW Status (R Range) | PNP switch status / ON or OFF |
| When the shift lever position displayed on the intelligent tester differs from the actual position, adjustment of the PNP switch or the shift cable may be incorrect. |
| Shift SW Status (D Range) | PNP switch status / ON or OFF |
| When the shift lever position displayed on the intelligent tester differs from the actual position, adjustment of the PNP switch or the shift cable may be incorrect. |
| 1.CHECK HARNESS AND CONNECTOR (BATTERY - PARK/NEUTRAL POSITION SWITCH) |
![]() |
Disconnect the park/neutral position switch assembly connector.
Turn the engine switch on (IG).
Measure the voltage according to the value(s) in the table below.
| Tester Connection | Switch Condition | Specified Condition |
| E4-1 (RB) - Body ground | Engine switch on (IG) | 11 to 14 V |
| *a | Front view of wire harness connector (to Park/Neutral Position Switch Assembly) |
|
| ||||
| OK | |
| 2.CHECK HARNESS AND CONNECTOR (OUTPUT SIGNAL) |
![]() |
Turn the engine switch on (IG).
Measure the voltage according to the value(s) in the table below.
| Tester Connection | Switch Condition | Specified Condition |
| E4-4 (B) - Body ground | Engine switch on (IG) | 11 to 14 V |
| *a | Front view of wire harness connector (to Park/Neutral Position Switch Assembly) |
|
| ||||
| OK | |
| 3.INSPECT PARK/NEUTRAL POSITION SWITCH ASSEMBLY |
![]() |
Disconnect the park/neutral position switch assembly connector.
Measure the resistance according to the value(s) in the table below when the shift lever is moved to each position.
| Tester Connection | Shift Lever Position | Specified Condition |
| E4-4 (B) - E4-9 (L) | P or N | Below 1 Ω |
| Except P and N | 10 kΩ or higher | |
| E4-1 (RB) - E4-2 (RL) | R | Below 1 Ω |
| Except R | 10 kΩ or higher | |
| E4-1 (RB) - E4-7 (DL) | D, S, "+" or "-" | Below 1 Ω |
| Except D, S, "+" and "-" | 10 kΩ or higher |
| *a | Component without harness connected (Park/Neutral Position Switch Assembly) |
|
| ||||
| OK | |
| 4.CHECK HARNESS AND CONNECTOR (PARK/NEUTRAL POSITION SWITCH - TCM) |
![]() |
Connect the park/neutral position switch assembly connector.
Disconnect the TCM connectors.
Turn the engine switch on (IG), and measure the voltage according to the value(s) in the table below when the shift lever is moved to each position.
| Tester Connection | Shift Lever Position | Specified Condition |
| E7-15 (R) - Body ground | R | 11 to 14 V* |
| Except R | Below 1 V | |
| E7-16 (D) - Body ground | D, S, "+" or "-" | 11 to 14 V |
| Except D, S, "+" and "-" | Below 1 V |
| *a | Front view of wire harness connector (to TCM) |
|
| ||||
| OK | ||
| ||
| 5.CHECK HARNESS AND CONNECTOR (PARK/NEUTRAL POSITION SWITCH - TCM) |
Turn the engine switch off.
Disconnect the TCM connector.
Disconnect the park/neutral position switch assembly connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
| E4-4 (B) - E7-11 (NSW) | Always | Below 1 Ω |
| Tester Connection | Condition | Specified Condition |
| E4-4 (B) or E7-11 (NSW) - Body ground and other terminals | Always | 10 kΩ or higher |
|
| ||||
| OK | ||
| ||