Home › Drivetrain · U241E AUTOMATIC TRANSMISSION / TRANSAXLE › AUTOMATIC TRANSAXLE SYSTEM

DTC    P0705    Transmission Range Sensor Circuit Malfunction (PRNDL Input)

for Preparation Click here


DESCRIPTION

The park/neutral position switch detects the shift lever position and sends signals to the ECM.

DTC No.
DTC Detection Condition
Trouble Area
P0705
(A) Any 2 or more signals of the following are ON simultaneously (2-trip detection logic)
  1. P input signal is ON.
  2. N input signal is ON.
  3. R input signal is ON.
  4. D input signal is ON.
(B) Any 2 or more signals of the following are ON simultaneously (2-trip detection logic)
  1. NSW input signal is ON.
  2. R input signal is ON.
  3. D input signal is ON
(C) When any of following conditions is met for 2.0 sec. or more in the S position (2-trip detection logic)
  1. NSW input signal is ON.
  2. P input signal is ON.
  3. N input signal is ON.
  4. R input signal is ON.
(D) All switches are OFF simultaneously for NSW, P, N, R, D positions (2-trip detection logic).
  1. NSW input signal is OFF.
  2. P input signal is OFF.
  3. N input signal is OFF.
  4. R input signal is OFF.
  5. D input signal is OFF
  1. Open or short in park/neutral position switch circuit
  2. Park/neutral position switch
  3. ECM

MONITOR DESCRIPTION

These DTCs indicate a problem with the park/neutral position switch and the wire harness in the park/neutral position switch circuit.
The park/neutral position switch detects the shift lever position and sends a signal to the ECM.
For security, the park/neutral position switch detects the shift lever position so that engine can be started only when the shift lever is in the P or N position.
The park/neutral position switch sends a signal to the ECM according to the shift position (P, R, N, or D). The ECM determines that there is a problem with the switch or related parts if it receives more than 1 position signal simultaneously. The ECM will turn on the MIL and store the DTC.

WIRING DIAGRAM


C253181E05


INSPECTION PROCEDURE

1.CHECK HARNESS AND CONNECTOR (BATTERY - PARK/NEUTRAL POSITION SWITCH)


    C248760E03
  1. Disconnect the park/neutral position switch connector.

  1. Turn the ignition switch to ON.

  1. Measure the voltage according to the value(s) in the table below.

    Standard Voltage:
    Tester Connection
    Condition
    Specified Condition
    E4-2 (RB) - Body ground
    Ignition switch ON
    11 to 14 V

    Text in Illustration 
    *a
    Front view of wire harness connector
    (to Park/Neutral Position Switch)



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK


2.CHECK HARNESS AND CONNECTOR (OUTPUT SIGNAL)


    C248760E04
  1. Turn the ignition switch to ON.

  1. Measure the voltage according to the value(s) in the table below.

    Standard Voltage:
    Tester Connection
    Condition
    Specified Condition
    E4-4 (B) - Body ground
    Ignition switch ON
    11 to 14 V

    Text in Illustration 
    *a
    Front view of wire harness connector
    (to Park/Neutral Position Switch)



NG
Go to step 8
OK


3.INSPECT PARK/NEUTRAL POSITION SWITCH ASSEMBLY


    C248761E02
  1. Disconnect the park/neutral position switch connector.

  1. Measure resistance according to the value(s) in the table below when the shift lever is moved to each position.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    4 - 5
    Shift lever in P and N
    Below 1 Ω
    Shift lever not in P and N
    10 Ω or higher
    2 - 6
    Shift lever in P
    Below 1 Ω
    Shift lever not in P
    10 Ω or higher
    2 - 1
    Shift lever in R
    Below 1 Ω
    Shift lever not in R
    10 Ω or higher
    2 - 9
    Shift lever in N
    Below 1 Ω
    Shift lever not in N
    10 Ω or higher
    2 - 7
    Shift lever in D, S, "+" and "-"
    Below 1 Ω
    Shift lever not in D, S, "+" and "-"
    10 Ω or higher

    Text in Illustration 
    *a
    Component without harness connected
    (Park/Neutral Position Switch)



NG
REPLACE PARK/NEUTRAL POSITION SWITCH ASSEMBLY (Click here)
OK


4.CHECK HARNESS AND CONNECTOR (PARK/NEUTRAL POSITION SWITCH - ECM)
  1. Connect the park/neutral position switch connector.

  1. Disconnect the ECM connector.



    C198503E16
  1. Turn the ignition switch to ON, and measure the voltage according to the value(s) in the table below when the shift lever is moved to each position.

    Standard Voltage:
    Tester Connection
    Condition
    Specified Condition
    E83-73 (P) - Body ground
    Shift lever in P
    11 to 14 V
    Shift lever not in P
    Below 1 V
    E83-54 (N) - Body ground
    Shift lever in N
    11 to 14 V
    Shift lever not in N
    Below 1 V
    E83-53 (R) - Body ground
    Shift lever in R
    11 to 14 V *
    Shift lever not in R
    Below 1 V
    E83-56 (D) - Body ground
    Shift lever in D and S
    11 to 14 V
    Shift lever not in D and S
    Below 1 V

    Text in Illustration 
    *a
    Front view of wire harness connector
    (to ECM)

    HINT:
    *: The voltage will drop slightly due to the turning on of the back up light.



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK


5.CHECK HARNESS AND CONNECTOR (BATTERY - TRANSMISSION CONTROL SWITCH)


    C245154E01
  1. Disconnect the transmission control switch connector.

  1. Turn the ignition switch to ON.

  1. Measure the voltage according to the value(s) in the table below.

    Standard Voltage:
    Tester Connection
    Switch Condition
    Specified Condition
    I44-4 (IG) - Body ground
    Ignition switch ON
    11 to 14 V

    Text in Illustration 
    *a
    Front view of wire harness connector
    (to Transmission Control Switch)



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK


6.INSPECT LOWER SHIFT LEVER ASSEMBLY (TRANSMISSION CONTROL SWITCH)


    C239095E12
  1. Disconnect the transmission control switch connector.

  1. Measure the resistance according to the value(s) in the table below when the shift lever is moved to each position.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    I44-4 (IG) - I44-5 (S)
    Shift lever in S, "+" and "-"
    Below 1 Ω
    Shift lever not in S, "+" and "-"
    10 Ω or higher

    Text in Illustration 
    *a
    Component without harness connected
    (Transmission Control Switch)



NG
REPLACE LOWER SHIFT LEVER ASSEMBLY (Click here)
OK


7.CHECK HARNESS AND CONNECTOR (TRANSMISSION CONTROL SWITCH - ECM)
  1. Connect the transmission control switch connector.

  1. Disconnect the ECM connector.



    C198503E17
  1. Turn the ignition switch to ON, and measure the voltage according to the value(s) in the table below when the shift lever is moved to each position.

    Standard Voltage:
    Tester Connection
    Condition
    Specified Condition
    E83-74 (S) - Body ground
    Shift lever in S, "+" and "-"
    11 to 14 V
    Shift lever not in S, "+" and "-"
    Below 1 V

    Text in Illustration 
    *a
    Front view of wire harness connector
    (to ECM)



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK

REPLACE ECM (Click here)  

8.CHECK HARNESS AND CONNECTOR (PARK/NEUTRAL POSITION SWITCH - ECM)
  1. Turn the ignition switch off.

  1. Disconnect the ECM connector.



    C162103E30
  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance (Check for open):
    Tester Connection
    Condition
    Specified Condition
    E4-4 (B) - E83-52 (NSW)
    Always
    Below 1 Ω

    Standard Resistance (Check for short):
    Tester Connection
    Condition
    Specified Condition
    E4-4 (B) or E83-52 (NSW) - Body ground
    Always
    10 kΩ or higher

    Text in Illustration 
    *a
    Front view of wire harness connector
    (to Park/Neutral Position Switch)
    *b
    Front view of wire harness connector
    (to ECM)



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK

REPLACE ECM (Click here)