CAN COMMUNICATION SYSTEM > Check CAN Bus Lines for Short Circuit (LHD Models) |
| Symptom | Trouble Area |
| Resistance between terminals 6 (CANH) and 14 (CANL) of DLC3 is below 54 Ω. |
|


| 1.CHECK FOR SHORT IN CAN BUS LINES (DLC3 BRANCH LINE) |
Disconnect the cable from the negative (-) battery terminal.
![]() |
Disconnect the DLC3 branch line connector (I96) from the CAN No. 1 junction connector.
| *a | Rear view of wire harness connector (to CAN No. 1 Junction Connector) |
| *b | to DLC3 |
![]() |
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
| I39-6 (CANH) - I39-14 (CANL) | Cable disconnected from negative (-) battery terminal | 1 MΩ or higher |
| *1 | DLC3 |
|
| ||||
| OK | |
| 2.CHECK FOR SHORT IN CAN BUS LINES (BRANCH LINE) |
Reconnect the DLC3 branch line connector (I96) to the CAN No. 1 junction connector.
![]() |
Connect the probes of an ohmmeter to terminals 6 (CANH) and 14 (CANL) of the DLC3.
| *1 | DLC3 |
While observing the resistance value shown on the tester, disconnect connectors (I112, I95, I97, I103, I100, I107, I106, I105, I102, I173 and I111) from the CAN No. 1 junction connector or CAN No. 2 junction connector one by one until the resistance becomes normal (between 54 and 69 Ω).

| *A | w/ Toyota Parking Assist-sensor System | *B | w/ Smart Entry and Start System |
| *C | for Navigation Receiver Type | *D | for Radio and Display Type |
| *E | w/ AFS | *F | Separate Type Yaw Rate Sensor |
| *1 | Clearance Warning ECU Assembly | *2 | Air Conditioning Amplifier Assembly |
| *3 | ECM | *4 | Brake Actuator Assembly |
| *5 | Smart Key ECU Assembly (Certification ECU) | *6 | Yaw Rate Sensor |
| *7 | Navigation ECU Sub-assembly | *8 | Radio and Display Receiver Assembly |
| *9 | Combination Meter Assembly | *10 | Power Steering ECU with Motor Assembly |
| *11 | DLC3 | *12 | Airbag Sensor Assembly |
| *13 | Steering Sensor | *14 | Main Body ECU (Multiplex Network Body ECU) |
| *15 | AFS ECU | *16 | CAN No. 2 Junction Connector |
| *17 | CAN No. 1 Junction Connector | - | - |

| *a | Component without harness connected (CAN No. 1 Junction Connector) | - | - |
| CAN No. 1 Junction Connector Side | Code | Color (CANH Side) | Color (CANL Side) |
| AFS ECU*1 | I112 | BE | W |
| Main body ECU (Multiplex network body ECU) | I95 | P | W |
| Steering sensor | I97 | V | W |
| Airbag sensor assembly | I103 | Y | W |
| DLC3 | I96 | L | W |
| Power steering ECU with motor assembly | I100 | G | W |
| Combination meter assembly | I94 | R | W |
| CAN main bus line (bus line connecting CAN No. 1 junction connector and CAN No. 2 junction connector) | I93 | B | W |

| *a | Component without harness connected (CAN No. 2 Junction Connector) | - | - |
| CAN No. 2 Junction Connector Side | Code | Color (CANH Side) | Color (CANL Side) |
| CAN main bus line (bus line connecting CAN No. 1 junction connector and CAN No. 2 junction connector) | I101 | B | W |
| I107 | R | W |
| Yaw rate sensor*5 | I173 | G | W |
| Smart key ECU assembly (Certification ECU)*3 | I106 | L | W |
| Brake actuator assembly | I105 | Y | W |
| Air conditioning amplifier assembly | I102 | V | W |
| ECM | I104 | P | W |
| Clearance warning ECU assembly*4 | I111 | BE | W |
| Symptom | Proceed to |
| The resistance is still below 54 Ω when all the specified connectors are disconnected. (There are no shorts between a pair of the branch lines.) | A |
| The resistance becomes normal (between 54 and 69 Ω) when a connector is disconnected. (There is a short between one or more pairs of branch lines.) | B |
When there is a short in one or more of the branch lines:
Reconnect all of the connectors to the CAN J/C, except for the one that was disconnected last (the short-circuited bus line). Check that the resistance shown on the tester is normal (between 54 and 69 Ω) to confirm that there is a short in the one branch line only.
|
| ||||
| A | |
| 3.CHECK FOR SHORT IN CAN BUS LINES (COMBINATION METER ASSEMBLY MAIN LINE) |
![]() |
Disconnect the combination meter assembly main bus line connector (I94) from the CAN No. 1 junction connector.
| *a | Rear view of wire harness connector (to CAN No. 1 Junction Connector) |
| *b | to Combination Meter Assembly |
![]() |
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
| I39-6 (CANH) - I39-14 (CANL) | Cable disconnected from negative (-) battery terminal | 108 to 132 Ω |
| *1 | DLC3 |
| Symptom | Proceed to |
| The resistance is still below 54 Ω when the combination meter assembly connector is disconnected. (There are no shorts in the combination meter assembly or between its main bus lines.) | A |
| The resistance falls within the specified range (between 108 and 132 Ω) (the other terminating resistor is normal) when the combination meter assembly connector is disconnected. (There is a short in the combination meter assembly or between its main bus lines.) | B |
|
| ||||
| A | |
| 4.CHECK FOR SHORT IN CAN BUS LINES (ECM MAIN LINE) |
![]() |
Disconnect the ECM main bus line connector (I104) from the CAN No. 2 junction connector.
| *a | Rear view of wire harness connector (to CAN No. 2 Junction Connector) |
| *b | to ECM |
![]() |
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
| I39-6 (CANH) - I39-14 (CANL) | Cable disconnected from negative (-) battery terminal | 1 MΩ or higher |
| *1 | DLC3 |
| Symptom | Proceed to |
| The resistance is still below 1 MΩ when the ECM connector is disconnected. (There are no shorts in the ECM or between its main bus lines.) | A |
| The resistance becomes 1 MΩ or more when the ECM connector is disconnected. (There is a short in the ECM or between its main bus lines.) | B |
|
| ||||
| A | |
| 5.CHECK CAN NO. 1 JUNCTION CONNECTOR |
![]() |
Disconnect the CAN main bus line connector (I93) from the CAN No. 1 junction connector.
| *a | Rear view of wire harness connector (to CAN No. 1 Junction Connector) |
| *b | to CAN No. 2 Junction Connector |
![]() |
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
| I39-6 (CANH) - I39-14 (CANL) | Cable disconnected from negative (-) battery terminal | 1 MΩ or higher |
| *1 | DLC3 |
|
| ||||
| OK | |
| 6.CHECK CAN NO. 2 JUNCTION CONNECTOR (CAN NO. 1 J/C - CAN NO. 2 J/C) |
Reconnect the CAN main bus line connector (I93) to the CAN No. 1 junction connector.
![]() |
Disconnect the CAN main bus line connector (I101) from the CAN No. 2 junction connector.
| *a | Rear view of wire harness connector (to CAN No. 2 Junction Connector) |
| *b | to CAN No. 1 Junction Connector |
![]() |
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
| I39-6 (CANH) - I39-14 (CANL) | Cable disconnected from negative (-) battery terminal | 1 MΩ or higher |
| *1 | DLC3 |
|
| ||||
| OK | ||
| ||
| 7.CHECK FOR SHORT IN CAN BUS LINES (ECU, SENSOR) |
Reconnect the connector for the short-circuited branch line to the CAN J/C (the connector that caused the bus line resistance to become normal (between 54 and 69 Ω) when it was disconnected).
Disconnect the connector that includes the DLC3 connected CAN lines (such as CANH and CANL) from the ECU (or sensor) to which the short-circuited branch line is connected (Click here).
![]() |
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
| I39-6 (CANH) - I39-14 (CANL) | Cable disconnected from negative (-) battery terminal | 54 to 69 Ω |
| *1 | DLC3 |
|
| ||||
| OK | ||
| ||
| 8.CHECK FOR SHORT IN CAN BUS LINES (COMBINATION METER ASSEMBLY) |
Reconnect the combination meter assembly main bus line connector (I94) to the CAN No. 1 junction connector.
Disconnect the combination meter assembly connector.
![]() |
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
| I39-6 (CANH) - I39-14 (CANL) | Cable disconnected from negative (-) battery terminal | 108 to 132 Ω |
| *1 | DLC3 |
|
| ||||
| OK | ||
| ||
| 9.CHECK FOR SHORT IN CAN BUS LINES (ECM) |
Reconnect the ECM main bus line connector (I104) to the CAN No. 2 junction connector.
Disconnect the ECM connector.
![]() |
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
| I39-6 (CANH) - I39-14 (CANL) | Cable disconnected from negative (-) battery terminal | 1 MΩ or higher |
| *1 | DLC3 |
| Result | Proceed to |
| OK (for 2GR-FE) | A |
| OK (for 2AR-FE) | B |
| NG | C |
|
| ||||
|
| ||||
| A | ||
| ||