Home › Engine / Hybrid System · 1AZ-FE › ENGINE CONTROL › SFI SYSTEM

DTC    P0504    Brake Switch "A" / "B" Correlation

for Preparation Click here


DESCRIPTION

The stop light switch assembly is a duplex system that transmits two signals: STP and ST1-. These two signals are used by the ECM to monitor whether or not the brake system is working properly. If the signals, which indicate the brake pedal is being depressed and released, are detected simultaneously, the ECM interprets this as a malfunction in the stop light switch assembly and stores the DTC.

HINT:
The normal signal conditions are as shown in the table below.

Signal (ECM Terminal)
Brake Pedal Released
In Transition
Brake Pedal Depressed
STP
OFF
ON
ON
ST1-
ON
ON
OFF
  1. [OFF] denotes ground potential.
  2. [ON] denotes battery potential (+B).
  3. On the intelligent tester, both the Data List items Stop Light Switch and ST1 are ON when the brake pedal is depressed because the ST1 indication characteristic is opposite to the Stop Light Switch indication.


DTC No.
DTC Detection Condition
Trouble Area
P0504
Conditions (a) and (b) continue for 0.5 seconds or more (1 trip detection logic):
(a) Ignition switch ON
(b) STP signal off when ST1- signal off
  1. Open or short in stop light switch signal circuit
  2. Stop light switch assembly
  3. No. 1 integration relay
  4. ECM

WIRING DIAGRAM


A266787E03


INSPECTION PROCEDURE

NOTICE:
Inspect the fuses for circuits related to this system before performing the following inspection procedure.

HINT:
  1. Read freeze frame data using the intelligent tester. The ECM records vehicle and driving condition information as freeze frame data the moment a DTC is stored. When troubleshooting, freeze frame data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, if the air fuel ratio was lean or rich, and other data from the time the malfunction occurred.
  2. Stop light switch assembly conditions can be checked using the intelligent tester.
    1. Connect the intelligent tester to the DLC3.
    2. Turn the ignition switch to ON.
    3. Turn the tester on.
    4. Enter the following menus: Powertrain / Engine and ECT / Data List / All Data / Stop Light Switch and ST1.
    5. Check the Data List indication when the brake pedal is depressed and released.

      Brake Pedal Operation
      Stop Light Switch
      ST1
      Depressed
      ON
      ON
      Released
      OFF
      OFF

1.CHECK TERMINAL VOLTAGE (POWER SOURCE OF STOP LIGHT SWITCH ASSEMBLY)


    A203090E14
  1. Disconnect the stop light switch assembly connector.

  1. Measure the voltage according to the value(s) in the table below.

    Standard Voltage:
    Tester Connection
    Condition
    Specified Condition
    A33-2 - Body ground
    Always
    11 to 14 V

    Text in Illustration 
    *a
    Front view of wire harness connector
    (to Stop Light Switch Assembly)



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR (BATTERY - STOP LIGHT SWITCH ASSEMBLY)
OK


2.CHECK TERMINAL VOLTAGE (POWER SOURCE OF STOP LIGHT SWITCH ASSEMBLY)


    A203090E14
  1. Disconnect the stop light switch assembly connector.

  1. Turn the ignition switch to ON.

  1. Measure the voltage according to the value(s) in the table below.

    Standard Voltage:
    Tester Connection
    Condition
    Specified Condition
    A33-4 - Body ground
    Ignition switch ON
    11 to 14 V

    Text in Illustration 
    *a
    Front view of wire harness connector
    (to Stop Light Switch Assembly)



NG
Go to step 5
OK


3.INSPECT STOP LIGHT SWITCH ASSEMBLY
  1. Inspect the stop light switch assembly (Click here).



NG
REPLACE STOP LIGHT SWITCH ASSEMBLY (Click here)
OK


4.CHECK TERMINAL VOLTAGE (STP AND ST1- VOLTAGE)


  1. Disconnect the ECM connector.


    A194116E29

  1. Turn the ignition switch to ON.

  1. Measure the voltage according to the value(s) in the table below.

    Standard Voltage:

    Tester Connection
    Condition
    Specified Condition
    A74-35 (ST1-) - Body ground
    Brake pedal released
    7.5 to 14 V
    Brake pedal depressed
    Below 1.5 V
    A74-36 (STP) - Body ground
    Brake pedal released
    Below 1.5 V
    Brake pedal depressed
    7.5 to 14 V


    Text in Illustration 
    *a
    Brake pedal depressed
    *b
    Brake pedal released
    *c
    Front view of wire harness connector
    (to ECM)
    -
    -



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR (STOP LIGHT SWITCH ASSEMBLY - ECM)
OK

REPLACE ECM (Click here)  

5.CHECK HARNESS AND CONNECTOR (NO. 1 INTEGRATION RELAY - STOP LIGHT SWITCH ASSEMBLY)
  1. Remove the No. 1 integration relay from the engine room relay block and junction block assembly.

  1. Disconnect the stop light switch assembly connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:

    Tester Connection
    Condition
    Specified Condition
    1C-2 - A33-4
    Always
    Below 1 Ω
    1C-2 or A33-4 - Body ground
    Always
    10 kΩ or higher



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK

REPLACE NO. 1 INTEGRATION RELAY (Click here)