CYLINDER HEAD > INSPECTION |
| 1. INSPECT CYLINDER HEAD SUB-ASSEMBLY |
![]() |
| *a | Cylinder Head Lower Side |
| *b | Intake Side |
| *c | Exhaust Side |
Using a precision straightedge and feeler gauge, measure the warpage of the contact surface of the cylinder block sub-assembly and manifolds.
| Item | Warpage |
| Cylinder head lower | 0.05 mm (0.00197 in.) |
| Intake | 0.08 mm (0.00315 in.) |
| Exhaust | 0.08 mm (0.00315 in.) |
| Item | Warpage |
| Cylinder head lower | 0.10 mm (0.00394 in.) |
| Intake | 0.10 mm (0.00394 in.) |
| Exhaust | 0.10 mm (0.00394 in.) |
| 2. INSPECT CYLINDER HEAD FOR CRACKS |
![]() |
Using a dye penetrant, check the intake ports, exhaust ports and cylinder surface for cracks.
If cracked, replace the cylinder head sub-assembly.
| 3. INSPECT INTAKE VALVE |
![]() |
Using a micrometer, measure the diameter of the valve stem.
![]() |
Using a vernier caliper, measure the valve head margin thickness.
| *a | Margin thickness |
![]() |
Using a vernier caliper, measure the valve overall length.
| *a | Overall Length |
| 4. INSPECT EXHAUST VALVE |
![]() |
Using a micrometer, measure the diameter of the valve stem.
![]() |
Using a vernier caliper, measure the valve head margin thickness.
| *a | Margin thickness |
![]() |
Using a vernier caliper, measure the valve overall length.
| *a | Overall Length |
| 5. INSPECT INTAKE VALVE SEAT |
Apply a light coat of Prussian blue to the valve face.
Lightly press the valve face against the valve seat.
![]() |
Check the valve face and valve seat by using the following procedure:
| *a | Width |
If Prussian blue appears around the entire valve face, the valve face is concentric. If not, replace the valve.
If Prussian blue appears around the entire valve seat, the valve seat and valve face are concentric. If not, resurface the valve seat.
Check that the valve seat contacts the middle of the valve face with the width between 1.1 and 1.5 mm (0.0433 and 0.0591 in.).
| 6. INSPECT EXHAUST VALVE SEAT |
Apply a light coat of Prussian blue to the valve face.
Lightly press the valve face against the valve seat.
![]() |
Check the valve face and valve seat by using the following procedure:
| *a | Width |
If Prussian blue appears around the entire valve face, the valve face is concentric. If not, replace the valve.
If Prussian blue appears around the entire valve seat, the valve seat and valve face are concentric. If not, resurface the valve seat.
Check that the valve seat contacts the middle of the valve face with the width between 1.1 and 1.5 mm (0.0433 and 0.0591 in.).
| 7. INSPECT INNER COMPRESSION SPRING |
![]() |
Using a vernier caliper, measure the free length of the inner compression spring.
![]() |
Using a steel square, measure the deviation of the inner compression spring.
| *a | Deviation |
| 8. INSPECT VALVE GUIDE BUSH OIL CLEARANCE |
![]() |
Using a caliper gauge, measure the inside diameter of the valve guide bush.
Subtract the valve stem diameter measurement from the valve guide bush inside diameter measurement.
| Item | Clearance |
| Intake | 0.025 to 0.060 mm (0.000984 to 0.00236 in.) |
| Exhaust | 0.030 to 0.065 mm (0.00118 to 0.00256 in.) |
| Item | Clearance |
| Intake | 0.08 mm (0.00315 in.) |
| Exhaust | 0.10 mm (0.00394 in.) |