Home › Brake › BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS › VEHICLE STABILITY CONTROL SYSTEM

VEHICLE STABILITY CONTROL SYSTEM > FREEZE FRAME DATA

for Preparation Click here



FREEZE FRAME DATA
  1. Whenever an ABS DTC is detected, the skid control ECU stores the current vehicle (ECU or sensor) state as Freeze Frame Data.

  2. The skid control ECU stores the number of times (maximum: 31) the ignition switch has been turned from off to ON since the last time the ABS was activated.

    HINT:
    1. However, if the vehicle is stopped or driven at a low speed (7 km/h (4.3 mph) or less), or if a DTC is detected, the skid control ECU will stop counting the number.
    2. Freeze Frame Data at the time the ABS operates:
      The skid control ECU stores and updates data whenever the ABS system operates.
      When the ECU stores data at the time a DTC is detected, the data stored during ABS operation is cleared.
    3. Freeze Frame Data at the time a DTC is detected:
      When the skid control ECU stores data at the time a DTC is detected, no updates will be performed until the data is cleared.


CHECK FREEZE FRAME DATA
  1. Turn the ignition switch off.

  2. Connect the intelligent tester to the DLC3.

  3. Turn the ignition switch to ON.

  4. Turn the intelligent tester on.

  5. Enter the following menus: Chassis / ABS/VSC/ TRC / DTC.

  6. Select a DTC to display its Freeze Frame Data.

    ABS/VSC/TRC 
    Tester Display
    Measurement Item/Range
    Normal Condition
    Diagnostic Note
    Elapsed Time after Freeze Trigger
    Elapsed time after freeze trigger / Min.: 0 msec, Max.: 500 msec
    -
    -
    Number of IG ON
    Number of times ignition switch turned to ON after Freeze Frame Data stored / 0 to 31
    -
    -
    Stop Light SW
    Stop light switch / ON or OFF
    ON: Brake pedal depressed
    OFF: Brake pedal released
    -
    Parking Brake SW
    Parking brake switch / ON or OFF
    ON: Parking brake applied
    OFF: Parking brake released
    -
    Gear Position
    Gear position information / "P,N", R, 1st-8th, Fail or Not R
    Actual gear position
    -
    Shift Lever Position
    Shift lever position information / "P,N", R, D/M, 1st-6th/B or Fail
    Actual shift lever position
    -
    Operated System
    Operated system status / ABS, VSC, TRC, BA, HAB, PBA, PB, HA-CTRL, TSC, Fail, Sys or Non
    Actual operated system
    ABS: ABS activated
    VSC: VSC activated
    TRC: TRC activated
    BA: BA activated
    HAB: HAB activated
    PBA: PBA activated
    PB: PB activated
    HA-CTRL: Hill-start assist control activated
    TSC: TSC activated
    Fail: Fail safe mode activated
    Sys: System prohibit activated
    Non: No operation activated
    Master Cylinder Sensor
    Master cylinder pressure sensor reading / Min.: 0.00 V, Max.: 5.00 V
    Brake pedal released: 0.20 to 0.40 V
    Reading increases when brake pedal is depressed
    M/C Sensor Grade
    Master cylinder pressure sensor change / Min.: -30 MPa/s, Max.: 225 MPa/s
    When brake pedal is released or pedal held at constant position: 0 MPa/s
    When brake pedal is being operated: Changes in proportion with pedal movement speed
    Yaw Rate Sensor
    Yaw rate sensor / Min.: -128 °/s, Max.: 127 °/s
    Vehicle stopped: 0 °/s
    Turning right: -128 to 0 °/s
    Turning left: 0 to 127 °/s
    -
    Lateral G
    Lateral G / Min.: -25.10 m/s2, Max.: 24.90 m/s2
    -
    During turning: Changes in proportion with acceleration
    Forward and Rearward G
    Forward and backward G / Min.: - 25.10 m/s2, Max.: 24.90 m/s2
    -
    During acceleration/deceleration: Changes in proportion with acceleration
    FR Wheel Speed
    Front wheel speed sensor RH reading / Min.: 0 km/h (0 mph), Max.: 326 km/h (202 mph)
    Vehicle stopped: 0 km/h (0 mph)
    When driving at constant speed: No large fluctuations
    FL Wheel Speed
    Front wheel speed sensor LH reading / Min.: 0 km/h (0 mph), Max.: 326 km/h (202 mph)
    Vehicle stopped: 0 km/h (0 mph)
    When driving at constant speed: No large fluctuations
    RR Wheel Speed
    Rear wheel speed sensor RH reading / Min.: 0 km/h (0 mph), Max.: 326 km/h (202 mph)
    Vehicle stopped: 0 km/h (0 mph)
    When driving at constant speed: No large fluctuations
    RL Wheel Speed
    Rear wheel speed sensor LH reading / Min.: 0 km/h (0 mph), Max.: 326 km/h (202 mph)
    Vehicle stopped: 0 km/h (0 mph)
    When driving at constant speed: No large fluctuations
    Vehicle Speed
    Maximum wheel speed sensor reading / Min.: 0 km/h (0 mph), Max.: 326 km/h (202 mph)
    Vehicle stopped: 0 km/h (0 mph)
    When driving at constant speed: No large fluctuations
    Vehicle Speed Grade
    Vehicle speed grade / Min.: -25.10 m/s2, Max.: 24.90 m/s2
    Vehicle stopped: 0 m/s2
    During driving: Changes in proportion with vehicle acceleration/deceleration
    Real Engine Torque
    Real engine torque / Min.: -1024.0 Nm, Max.: 1023.0 Nm
    -
    -
    Accelerator Opening Angle %
    The difference of a present accelerator / Min.: 0.0%, Max.: 128.0%
    When the accelerator pedal is released: 0.0%
    During accelerator pedal operation: Changes in proportion with the pedal movement
    Brake Pedal Load Sensing SW
    Brake pedal load sensing switch / ON or OFF
    ON: Brake pedal depressed beyond a specified point
    OFF: Brake pedal not depressed beyond a specified point
    -
    Inspection Mode
    Inspection mode / Other or Inspect
    Other: Normal mode
    Inspect: Inspection mode
    -
    Steering Angle Sensor
    Steering angle sensor / Min.: - 3276.8°, Max.: 3276.7°
    Turning left: Increases
    Turning right: Decreases
    -
    TRC/VSC Off Mode
    TRC/VSC off mode / Normal, TRC OFF or VSC OFF
    Normal: Normal mode
    TRC OFF: TRC off mode
    VSC OFF: VSC off mode
    -


CLEAR FREEZE FRAME DATA

NOTICE:
Clearing the DTC will also clear the Freeze Frame Data.

  1. Turn the ignition switch off.

  2. Connect the intelligent tester to the DLC3.

  3. Turn the ignition switch to ON.

  4. Clear the DTCs and Freeze Frame Data (Click here).