CAN COMMUNICATION SYSTEM > TERMINALS OF ECU |
| CAN NO. 1 JUNCTION CONNECTOR (for LHD) |
Check the CAN No. 1 junction connector.
Connection diagram

| *a | Component with harness connected (CAN No. 1 Junction Connector) | *b | to AFS ECU*1 (for V Bus) |
| *c | to Main Body ECU (Multiplex Network Body ECU) (for V Bus) | *d | to Steering Sensor (for V Bus) |
| *e | to Airbag Sensor Assembly (for V Bus) | *f | to DLC3 |
| *g | to Power Steering ECU with Motor Assembly (for V Bus) | *h | to Combination Meter Assembly (for V Bus) |
| *i | to CAN No. 2 Junction Connector (for V Bus) | - | - |
Check the connection diagram of the components which are connected to the CAN No. 1 junction connector.
| Terminal No. (Symbol) | Wiring Color | Connected to |
| I112-1 (CANH) | BE | AFS ECU*1 (for V bus) |
| I112-2 (CANL) | W | |
| I95-1 (CANH) | P | Main body ECU (Multiplex network body ECU) (for V bus) |
| I95-2 (CANL) | W | |
| I97-1 (CANH) | V | Steering sensor (for V bus) |
| I97-2 (CANL) | W | |
| I103-1 (CANH) | Y | Airbag sensor assembly (for V bus) |
| I103-2 (CANL) | W | |
| I96-1 (CANH) | L | DLC3 |
| I96-2 (CANL) | W | |
| I100-1 (CANH) | G | Power steering ECU with motor assembly (for V bus) |
| I100-2 (CANL) | W | |
| I94-1 (CANH) | R | Combination meter assembly (for V bus) |
| I94-2 (CANL) | W | |
| I93-1 (CANH) | B | CAN No. 2 junction connector (for V bus) |
| I93-2 (CANL) | W |
| CAN NO. 1 JUNCTION CONNECTOR (for RHD) |
Check the CAN No. 1 junction connector.
Connection diagram

| *a | Component with harness connected (CAN No. 1 Junction Connector) | *b | to Main Body ECU (Multiplex Network Body ECU) (for V Bus) |
| *c | to Air Conditioning Amplifier Assembly (for V Bus) | *d | to Airbag Sensor Assembly (for V Bus) |
| *e | to Power Steering ECU with Motor Assembly (for V Bus) | *f | to ECM (for V Bus) |
| *g | to Radio and Display Receiver Assembly*1 (for V Bus) | *h | to CAN No. 2 Junction Connector (for V Bus) |
Check the connection diagram of the components which are connected to the CAN No. 1 junction connector.
| Terminal No. (Symbol) | Wiring Color | Connected to |
| I95-1 (CANH) | P | Main body ECU (Multiplex network body ECU) (for V bus) |
| I95-2 (CANL) | W | |
| I102-1 (CANH) | V | Air conditioning amplifier assembly (for V bus) |
| I102-2 (CANL) | W | |
| I103-1 (CANH) | Y | Airbag sensor assembly (for V bus) |
| I103-2 (CANL) | W | |
| I100-1 (CANH) | L | Power steering ECU with motor assembly (for V bus) |
| I100-2 (CANL) | W | |
| I104-1 (CANH) | G | ECM (for V bus) |
| I104-2 (CANL) | W | |
| I107-1 (CANH) | R | Radio and display receiver assembly*1 (for V bus) |
| I107-2 (CANL) | W | |
| I93-1 (CANH) | B | CAN No. 2 junction connector (for V bus) |
| I93-2 (CANL) | W |
| CAN NO. 2 JUNCTION CONNECTOR (for LHD) |
Check the CAN No. 2 junction connector.
Connection diagram

| *a | Component with harness connected (CAN No. 2 Junction Connector) | *b | to Clearance Warning ECU Assembly*1 (for V Bus) |
| *c | to ECM (for V Bus) | *d | to Air Conditioning Amplifier Assembly (for V Bus) |
| *e | to Brake Actuator Assembly (for V Bus) | *f | to Smart Key ECU Assembly (Certification ECU)*2 (for V Bus) |
| *g |
| *h | to CAN No. 1 Junction Connector (for V Bus) |
Check the connection diagram of the components which are connected to the CAN No. 2 junction connector.
| Terminal No. (Symbol) | Wiring Color | Connected to |
| I111-1 (CANH) | BE | Clearance warning ECU assembly*1 (for V bus) |
| I111-2 (CANL) | W | |
| I104-1 (CANH) | P | ECM (for V bus) |
| I104-2 (CANL) | W | |
| I102-1 (CANH) | V | Air conditioning amplifier assembly (for V bus) |
| I102-2 (CANL) | W | |
| I105-1 (CANH) | Y | Brake actuator assembly (for V bus) |
| I105-2 (CANL) | W | |
| I106-1 (CANH) | L | Smart key ECU assembly (Certification ECU)*2 (for V bus) |
| I106-2 (CANL) | W | |
| I107-1 (CANH) | R |
|
| I107-2 (CANL) | W | |
| I101-1 (CANH) | B | CAN No. 1 junction connector (for V bus) |
| I101-2 (CANL) | W |
| CAN NO. 2 JUNCTION CONNECTOR (for RHD) |
Check the CAN No. 2 junction connector.
Connection diagram

| *a | Component with harness connected (CAN No. 2 Junction Connector) | *b | to Clearance Warning ECU Assembly (for V Bus) |
| *c | to Steering Sensor (for V Bus) | *d | to Brake Actuator Assembly (for V Bus) |
| *e | to Smart Key ECU Assembly (Certification ECU)*1 (for V Bus) | *f | DLC3 |
| *g | to Combination Meter Assembly (for V Bus) | *h | to CAN No. 1 Junction Connector (for V Bus) |
Check the connection diagram of the components which are connected to the CAN No. 2 junction connector.
| Terminal No. (Symbol) | Wiring Color | Connected to |
| I111-1 (CANH) | P | Clearance warning ECU assembly (for V bus) |
| I111-2 (CANL) | W | |
| I97-1 (CANH) | V | Steering sensor (for V bus) |
| I97-2 (CANL) | W | |
| I105-1 (CANH) | Y | Brake actuator assembly (for V bus) |
| I105-2 (CANL) | W | |
| I106-1 (CANH) | L | Smart key ECU assembly (Certification ECU)*1 (for V bus) |
| I106-2 (CANL) | W | |
| I96-1 (CANH) | G | DLC3 |
| I96-2 (CANL) | W | |
| I94-1 (CANH) | R | Combination meter assembly (for V bus) |
| I94-2 (CANL) | W | |
| I101-1 (CANH) | B | CAN No. 1 junction connector (for V bus) |
| I101-2 (CANL) | W |
| CAN NO. 3 JUNCTION CONNECTOR (w/ Power Tilt and Power Telescopic Steering Column System) |
Check the CAN No. 3 junction connector.
Connection diagram

| *A | for TMC Made | *B | for TMMR Made |
| *a | Component with harness connected (CAN No. 3 Junction Connector) | *b | to Multiplex Tilt and Telescopic ECU (for Sub Bus 1) |
| *c | to Main Body ECU (Multiplex Network Body ECU) (for Sub Bus 1) | *d | to CAN No. 4 Junction Connector (for Sub Bus 1) |
Check the connection diagram of the components which are connected to the CAN No. 3 junction connector.
| Terminal No. (Symbol) | Wiring Color | Connected to |
| I115-1 (CANH) | B | Multiplex tilt and telescopic ECU (for Sub bus 1) |
| I115-2 (CANL) | GR | |
| I114-1 (CANH) | R | Main body ECU (Multiplex network body ECU) (for Sub bus 1) |
| I114-2 (CANL) | GR | |
| I117-1 (CANH) | Y | CAN No. 4 junction connector (for Sub bus 1) |
| I117-2 (CANL) | GR |
| CAN NO. 4 JUNCTION CONNECTOR (w/ Power Tilt and Power Telescopic Steering Column System) |
Check the CAN No. 4 junction connector.
Connection diagram

| *a | Component with harness connected (CAN No. 4 Junction Connector) | *b | to CAN No. 5 Junction Connector (for Sub Bus 1) |
| *c | to CAN No. 3 Junction Connector (for Sub Bus 1) | - | - |
Check the connection diagram of the components which are connected to the CAN No. 4 junction connector.
| Terminal No. (Symbol) | Wiring Color | Connected to |
| I121-1 (CANH) | V | CAN No. 5 junction connector (for Sub bus 1) |
| I121-2 (CANL) | GR | |
| I120-1 (CANH) | Y | CAN No. 3 junction connector (for Sub bus 1) |
| I120-2 (CANL) | GR |
| CAN NO. 5 JUNCTION CONNECTOR (w/ Power Tilt and Power Telescopic Steering Column System) |
Check the CAN No. 5 junction connector.
![]() |
Connection diagram
| *a | Rear view of wire harness connector (to CAN No. 5 Junction Connector) |
| *b | to CAN No. 4 Junction Connector (for Sub Bus 1) |
Check the connection diagram of the components which are connected to the CAN No. 5 junction connector.
| Terminal No. (Symbol) | Wiring Color | Connected to |
| I123-3 (CANH) | V | CAN No. 4 junction connector (for Sub bus 1) |
| I123-2 (CANL) | GR |
| DLC3 |
Disconnect the cable from the negative (-) battery terminal.
Measure the resistance according to the value(s) in the table below.

| *1 | DLC3 | - | - |
| Terminal No. (Symbol) | Wiring Color | Terminal Description | Condition | Specified Condition |
| I39-6 (CANH) - I39-14 (CANL) | L - W*1 G - W*2 | HIGH-level CAN bus line - LOW-level CAN bus line | Cable disconnected from negative (-) battery terminal | 54 to 69 Ω |
| I39-6 (CANH) - I39-4 (CG) | L - W-B*1 G - W-B*2 | HIGH-level CAN bus line - Ground | Cable disconnected from negative (-) battery terminal | 200 Ω or higher |
| I39-14 (CANL) - I39-4 (CG) | W - W-B | LOW-level CAN bus line - Ground | Cable disconnected from negative (-) battery terminal | 200 Ω or higher |
| I39-6 (CANH) - I39-16 (BAT) | L - R*1 G - R*2 | HIGH-level CAN bus line - Battery positive (+) | Cable disconnected from negative (-) battery terminal | 6 kΩ or higher |
| I39-14 (CANL) - I39-16 (BAT) | W - R | LOW-level CAN bus line - Battery positive (+) | Cable disconnected from negative (-) battery terminal | 6 kΩ or higher |
| ECM (for 2GR-FE) |

| *a | Component without harness connected (ECM) | - | - |
Disconnect the cable from the negative (-) battery terminal.
Disconnect the ECM connectors.

| *a | Front view of wire harness connector (to ECM) | - | - |
Measure the resistance according to the value(s) in the table below.
| Terminal No. (Symbol) | Wiring Color | Terminal Description | Condition | Specified Condition |
| A25-13 (CANH) - A25-26 (CANL) | B - W | HIGH-level CAN bus line - LOW-level CAN bus line | Cable disconnected from negative (-) battery terminal | 108 to 132 Ω |
| A25-13 (CANH) - E26-49 (E1) | B - BR | HIGH-level CAN bus line - Ground | Cable disconnected from negative (-) battery terminal | 200 Ω or higher |
| A25-26 (CANL) - E26-49 (E1) | W - BR | LOW-level CAN bus line - Ground | Cable disconnected from negative (-) battery terminal | 200 Ω or higher |
| A25-13 (CANH) - A25-1 (BATT) | B - GR | HIGH-level CAN bus line - Battery positive (+) | Cable disconnected from negative (-) battery terminal | 6 kΩ or higher |
| A25-26 (CANL) - A25-1 (BATT) | W - GR | LOW-level CAN bus line - Battery positive (+) | Cable disconnected from negative (-) battery terminal | 6 kΩ or higher |
| ECM (for 2AR-FE) |

| *a | Component without harness connected (ECM) | - | - |
Disconnect the cable from the negative (-) battery terminal.
Disconnect the ECM connectors.

| *a | Front view of wire harness connector (to ECM) | - | - |
Measure the resistance according to the value(s) in the table below.
| Terminal No. (Symbol) | Wiring Color | Terminal Description | Condition | Specified Condition |
| A25-13 (CANH) - A25-26 (CANL) | B - W | HIGH-level CAN bus line - LOW-level CAN bus line | Cable disconnected from negative (-) battery terminal | 108 to 132 Ω |
| A25-13 (CANH) - E26-16 (E1) | B - BR | HIGH-level CAN bus line - Ground | Cable disconnected from negative (-) battery terminal | 200 Ω or higher |
| A25-26 (CANL) - E26-16 (E1) | W - BR | LOW-level CAN bus line - Ground | Cable disconnected from negative (-) battery terminal | 200 Ω or higher |
| A25-13 (CANH) - A25-1 (BATT) | B - GR | HIGH-level CAN bus line - Battery positive (+) | Cable disconnected from negative (-) battery terminal | 6 kΩ or higher |
| A25-26 (CANL) - A25-1 (BATT) | W - GR | LOW-level CAN bus line - Battery positive (+) | Cable disconnected from negative (-) battery terminal | 6 kΩ or higher |
| ECM (for 1AZ-FE) |

| *a | Component without harness connected (ECM) | - | - |
Disconnect the cable from the negative (-) battery terminal.
Disconnect the ECM connectors.

| *a | Front view of wire harness connector (to ECM) | - | - |
Measure the resistance according to the value(s) in the table below.
| Terminal No. (Symbol) | Wiring Color | Terminal Description | Condition | Specified Condition |
| A74-41 (CANH) - A74-49 (CANL) | B - W | HIGH-level CAN bus line - LOW-level CAN bus line | Cable disconnected from negative (-) battery terminal | 108 to 132 Ω |
| A74-41 (CANH) - E83-104 (E1) | B - BR | HIGH-level CAN bus line - Ground | Cable disconnected from negative (-) battery terminal | 200 Ω or higher |
| A74-49 (CANL) - E83-104 (E1) | W - BR | LOW-level CAN bus line - Ground | Cable disconnected from negative (-) battery terminal | 200 Ω or higher |
| A74-41 (CANH) - A74-20 (BATT) | B - GR | HIGH-level CAN bus line - Battery positive (+) | Cable disconnected from negative (-) battery terminal | 6 kΩ or higher |
| A74-49 (CANL) - A74-20 (BATT) | W - GR | LOW-level CAN bus line - Battery positive (+) | Cable disconnected from negative (-) battery terminal | 6 kΩ or higher |
| COMBINATION METER ASSEMBLY |

| *a | Component without harness connected (Combination Meter Assembly) | - | - |
Disconnect the cable from the negative (-) battery terminal.
![]() |
Disconnect the combination meter assembly connector.
| *a | Front view of wire harness connector (to Combination Meter Assembly) |
Measure the resistance according to the value(s) in the table below.
| Terminal No. (Symbol) | Wiring Color | Terminal Description | Condition | Specified Condition |
| I18-16 (CANH) - I18-15 (CANL) | R - W | HIGH-level CAN bus line - LOW-level CAN bus line | Cable disconnected from negative (-) battery terminal | 108 to 132 Ω |
| I18-16 (CANH) - I18-7 (ES) | R - BR | HIGH-level CAN bus line - Ground | Cable disconnected from negative (-) battery terminal | 200 Ω or higher |
| I18-15 (CANL) - I18-7 (ES) | W - BR | LOW-level CAN bus line - Ground | Cable disconnected from negative (-) battery terminal | 200 Ω or higher |
| I18-16 (CANH) - I18-1 (B) | R - W | HIGH-level CAN bus line - Battery positive (+) | Cable disconnected from negative (-) battery terminal | 6 kΩ or higher |
| I18-15 (CANL) - I18-1 (B) | W - W | LOW-level CAN bus line - Battery positive (+) | Cable disconnected from negative (-) battery terminal | 6 kΩ or higher |
| INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY AND MAIN BODY ECU (MULTIPLEX NETWORK BODY ECU) |

| *A | for LHD | *B | for RHD |
| *a | Component without harness connected (Instrument Panel Junction Block Assembly and Main Body ECU (Multiplex Network Body ECU)) | - | - |
Disconnect the cable from the negative (-) battery terminal.
Disconnect the main body ECU (multiplex network body ECU) connectors.

| *1 | DLC3 | - | - |
| *a | Front view of wire harness connector (to Main Body ECU (Multiplex Network Body ECU)) | - | - |
Measure the resistance according to the value(s) in the table below.
| Terminal No. (Symbol) | Wiring Color | Terminal Description | Condition | Specified Condition |
| I13-14 (CANH) - I13-13 (CANL) | P - W | HIGH-level CAN bus line - LOW-level CAN bus line | Cable disconnected from negative (-) battery terminal | 54 to 69 Ω |
| I13-14 (CANH) - I39-4 (CG) | P - W-B | HIGH-level CAN bus line - Ground | Cable disconnected from negative (-) battery terminal | 200 Ω or higher |
| I13-13 (CANL) - I39-4 (CG) | W - W-B | LOW-level CAN bus line - Ground | Cable disconnected from negative (-) battery terminal | 200 Ω or higher |
| I13-14 (CANH) - I39-16 (BAT) | P - R | HIGH-level CAN bus line - Battery positive (+) | Cable disconnected from negative (-) battery terminal | 6 kΩ or higher |
| I13-13 (CANL) - I39-16 (BAT) | W - R | LOW-level CAN bus line - Battery positive (+) | Cable disconnected from negative (-) battery terminal | 6 kΩ or higher |
| Terminal No. (Symbol) | Wiring Color | Terminal Description | Condition | Specified Condition |
| I12-9 (CANP) - I12-10 (CANN) | R - GR | HIGH-level CAN bus line - LOW-level CAN bus line | Cable disconnected from negative (-) battery terminal | 108 to 132 Ω |
| I12-9 (CANP) - I39-4 (CG) | R - W-B | HIGH-level CAN bus line - Ground | Cable disconnected from negative (-) battery terminal | 200 Ω or higher |
| I12-10 (CANN) - I39-4 (CG) | GR - W-B | LOW-level CAN bus line - Ground | Cable disconnected from negative (-) battery terminal | 200 Ω or higher |
| I12-9 (CANP) - I39-16 (BAT) | R - R | HIGH-level CAN bus line - Battery positive (+) | Cable disconnected from negative (-) battery terminal | 6 kΩ or higher |
| I12-10 (CANN) - I39-16 (BAT) | GR - R | LOW-level CAN bus line - Battery positive (+) | Cable disconnected from negative (-) battery terminal | 6 kΩ or higher |
| BRAKE ACTUATOR ASSEMBLY |

| *a | Component without harness connected (Brake Actuator Assembly) | - | - |
Disconnect the cable from the negative (-) battery terminal.
![]() |
Disconnect the brake actuator assembly connector.
| *a | Front view of wire harness connector (to Brake Actuator Assembly) |
Measure the resistance according to the value(s) in the table below.
| Terminal No. (Symbol) | Wiring Color | Terminal Description | Condition | Specified Condition |
| A49-26 (CANH) - A49-14 (CANL) | GR - W | HIGH-level CAN bus line - LOW-level CAN bus line | Cable disconnected from negative (-) battery terminal | 54 to 69 Ω |
| A49-26 (CANH) - A49-38 (GND1) | GR - W-B | HIGH-level CAN bus line - Ground | Cable disconnected from negative (-) battery terminal | 200 Ω or higher |
| A49-14 (CANL) - A49-38 (GND1) | W - W-B | LOW-level CAN bus line - Ground | Cable disconnected from negative (-) battery terminal | 200 Ω or higher |
| A49-26 (CANH) - A49-25 (+BS) | GR - L | HIGH-level CAN bus line - Battery positive (+) | Cable disconnected from negative (-) battery terminal | 6 kΩ or higher |
| A49-14 (CANL) - A49-25 (+BS) | W - L | LOW-level CAN bus line - Battery positive (+) | Cable disconnected from negative (-) battery terminal | 6 kΩ or higher |
| STEERING SENSOR |
Disconnect the cable from the negative (-) battery terminal.
![]() |
Disconnect the steering sensor connector.
| *a | Front view of wire harness connector (to Steering Sensor) |
Measure the resistance according to the value(s) in the table below.
| Terminal No. (Symbol) | Wiring Color | Terminal Description | Condition | Specified Condition |
| I29-3 (CANH) - I29-2 (CANL) | V - W | HIGH-level CAN bus line - LOW-level CAN bus line | Cable disconnected from negative (-) battery terminal | 54 to 69 Ω |
| I29-3 (CANH) - I29-1 (ESS) | V - W-B | HIGH-level CAN bus line - Ground | Cable disconnected from negative (-) battery terminal | 200 Ω or higher |
| I29-2 (CANL) - I29-1 (ESS) | W - W-B | LOW-level CAN bus line - Ground | Cable disconnected from negative (-) battery terminal | 200 Ω or higher |
| I29-3 (CANH) - I29-5 (BAT) | V - W | HIGH-level CAN bus line - Battery positive (+) | Cable disconnected from negative (-) battery terminal | 6 kΩ or higher |
| I29-2 (CANL) - I29-5 (BAT) | W - W | LOW-level CAN bus line - Battery positive (+) | Cable disconnected from negative (-) battery terminal | 6 kΩ or higher |
| POWER STEERING ECU WITH MOTOR ASSEMBLY |
Disconnect the cable from the negative (-) battery terminal.
Disconnect the power steering ECU with motor assembly connectors.

| *a | Component without harness connected (Power Steering ECU with Motor Assembly) | - | - |

| *a | Front view of wire harness connector (to Power Steering ECU with Motor Assembly) | - | - |
Measure the resistance according to the value(s) in the table below.
| Terminal No. (Symbol) | Wiring Color | Terminal Description | Condition | Specified Condition |
| j1-7 (CANH) - j1-8 (CANL) | Y - SB | HIGH-level CAN bus line - LOW-level CAN bus line | Cable disconnected from negative (-) battery terminal | 54 to 69 Ω |
| j1-7 (CANH) - j2-2 (PGND) | Y - B | HIGH-level CAN bus line - Ground | Cable disconnected from negative (-) battery terminal | 200 Ω or higher |
| j1-8 (CANL) - j2-2 (PGND) | SB - B | LOW-level CAN bus line - Ground | Cable disconnected from negative (-) battery terminal | 200 Ω or higher |
| j1-7 (CANH) - j2-1 (PIG) | Y - R | HIGH-level CAN bus line - Battery positive (+) | Cable disconnected from negative (-) battery terminal | 6 kΩ or higher |
| j1-8 (CANL) - j2-1 (PIG) | SB - R | LOW-level CAN bus line - Battery positive (+) | Cable disconnected from negative (-) battery terminal | 6 kΩ or higher |
| AIRBAG SENSOR ASSEMBLY |
Disconnect the cable from the negative (-) battery terminal.
Disconnect the airbag sensor assembly connector.

| *1 | DLC3 | - | - |
| *a | Front view of wire harness connector (to Airbag Sensor Assembly) | - | - |
Measure the resistance according to the value(s) in the table below.
| Terminal No. (Symbol) | Wiring Color | Terminal Description | Condition | Specified Condition |
| I47-13 (CANH) - I47-22 (CANL) | Y - W | HIGH-level CAN bus line - LOW-level CAN bus line | Cable disconnected from negative (-) battery terminal | 54 to 69 Ω |
| I47-13 (CANH) - I47-25 (E1) | Y - W-B | HIGH-level CAN bus line - Ground | Cable disconnected from negative (-) battery terminal | 200 Ω or higher |
| I47-22 (CANL) - I47-25 (E1) | W - W-B | LOW-level CAN bus line - Ground | Cable disconnected from negative (-) battery terminal | 200 Ω or higher |
| I47-13 (CANH) - I39-16 (BAT) | Y - R | HIGH-level CAN bus line - Battery positive (+) | Cable disconnected from negative (-) battery terminal | 6 kΩ or higher |
| I47-22 (CANL) - I39-16 (BAT) | W - R | LOW-level CAN bus line - Battery positive (+) | Cable disconnected from negative (-) battery terminal | 6 kΩ or higher |
| SMART KEY ECU ASSEMBLY (CERTIFICATION ECU) (w/ Smart Entry and Start System) |

| *a | Component without harness connected (Smart Key ECU Assembly (Certification ECU)) | - | - |
Disconnect the cable from the negative (-) battery terminal.
Disconnect the smart key ECU assembly (certification ECU) connectors.

| *a | Rear view of wire harness connector (to Smart Key ECU Assembly (Certification ECU)) | - | - |
Measure the resistance according to the value(s) in the table below.
| Terminal No. (Symbol) | Wiring Color | Terminal Description | Condition | Specified Condition |
| I78-14 (CANH) - I78-15 (CANL) | L - W | HIGH-level CAN bus line - LOW-level CAN bus line | Cable disconnected from negative (-) battery terminal | 54 to 69 Ω |
| I78-14 (CANH) - A43-11 (E) | L - W | HIGH-level CAN bus line - Ground | Cable disconnected from negative (-) battery terminal | 200 Ω or higher |
| I78-15 (CANL) - A43-11 (E) | W - W | LOW-level CAN bus line - Ground | Cable disconnected from negative (-) battery terminal | 200 Ω or higher |
| I78-14 (CANH) - A43-2 (+B) | L - W | HIGH-level CAN bus line - Battery positive (+) | Cable disconnected from negative (-) battery terminal | 6 kΩ or higher |
| I78-15 (CANL) - A43-2 (+B) | W - W | LOW-level CAN bus line - Battery positive (+) | Cable disconnected from negative (-) battery terminal | 6 kΩ or higher |
| RADIO AND DISPLAY RECEIVER ASSEMBLY (for Radio and Display Type) |

| *a | Component without harness connected (Radio and Display Receiver Assembly) | - | - |
Disconnect the cable from the negative (-) battery terminal.
Disconnect the radio and display receiver assembly connectors.

| *a | Front view of wire harness connector (to Radio and Display Receiver Assembly) | - | - |
Measure the resistance according to the value(s) in the table below.
| Terminal No. (Symbol) | Wiring Color | Terminal Description | Condition | Specified Condition |
| I155-9 (CANH) - I155-10 (CANL) | R - W | HIGH-level CAN bus line - LOW-level CAN bus line | Cable disconnected from negative (-) battery terminal | 54 to 69 Ω |
| I155-9 (CANH) - I152-7 (GND1) | R - BR | HIGH-level CAN bus line - Ground | Cable disconnected from negative (-) battery terminal | 200 Ω or higher |
| I155-10 (CANL) - I152-7 (GND1) | W - BR | LOW-level CAN bus line - Ground | Cable disconnected from negative (-) battery terminal | 200 Ω or higher |
| I155-9 (CANH) - I152-4 (+B1) | R - L-Y | HIGH-level CAN bus line - Battery positive (+) | Cable disconnected from negative (-) battery terminal | 6 kΩ or higher |
| I155-10 (CANL) - I152-4 (+B1) | W - L-Y | LOW-level CAN bus line - Battery positive (+) | Cable disconnected from negative (-) battery terminal | 6 kΩ or higher |
| NAVIGATION ECU SUB-ASSEMBLY (for Navigation Receiver Type) |

| *a | Component without harness connected (Navigation ECU Sub-assembly) | - | - |
Disconnect the cable from the negative (-) battery terminal.
Disconnect the navigation ECU sub-assembly connectors.

| *a | Front view of wire harness connector (to Navigation ECU Sub-assembly) | - | - |
Measure the resistance according to the value(s) in the table below.
| Terminal No. (Symbol) | Wiring Color | Terminal Description | Condition | Specified Condition |
| I67-9 (CANH) - I67-10 (CANL) | R - W | HIGH-level CAN bus line - LOW-level CAN bus line | Cable disconnected from negative (-) battery terminal | 54 to 69 Ω |
| I67-9 (CANH) - I64-7 (GND1) | R - BR | HIGH-level CAN bus line - Ground | Cable disconnected from negative (-) battery terminal | 200 Ω or higher |
| I67-10 (CANL) - I64-7 (GND1) | W - BR | LOW-level CAN bus line - Ground | Cable disconnected from negative (-) battery terminal | 200 Ω or higher |
| I67-9 (CANH) - I64-4 (+B1) | R - L-Y | HIGH-level CAN bus line - Battery positive (+) | Cable disconnected from negative (-) battery terminal | 6 kΩ or higher |
| I67-10 (CANL) - I64-4 (+B1) | W - L-Y | LOW-level CAN bus line - Battery positive (+) | Cable disconnected from negative (-) battery terminal | 6 kΩ or higher |
| AIR CONDITIONING AMPLIFIER ASSEMBLY |
Disconnect the cable from the negative (-) battery terminal.
Disconnect the air conditioning amplifier assembly connector.

| *a | Component without harness connected (Air Conditioning Amplifier Assembly) | - | - |

| *a | Front view of wire harness connector (to Air Conditioning Amplifier Assembly) | - | - |
Measure the resistance according to the value(s) in the table below.
| Terminal No. (Symbol) | Wiring Color | Terminal Description | Condition | Specified Condition |
| I77-11 (CANH) - I77-12 (CANL) | V - W | HIGH-level CAN bus line - LOW-level CAN bus line | Cable disconnected from negative (-) battery terminal | 54 to 69 Ω |
| I77-11 (CANH) - I77-14 (GND) | V - W-B | HIGH-level CAN bus line - Ground | Cable disconnected from negative (-) battery terminal | 200 Ω or higher |
| I77-12 (CANL) - I77-14 (GND) | W - W-B | LOW-level CAN bus line - Ground | Cable disconnected from negative (-) battery terminal | 200 Ω or higher |
| I77-11 (CANH) - I77-21 (B) | V - Y | HIGH-level CAN bus line - Battery positive (+) | Cable disconnected from negative (-) battery terminal | 6 kΩ or higher |
| I77-12 (CANL) - I77-21 (B) | W - Y | LOW-level CAN bus line - Battery positive (+) | Cable disconnected from negative (-) battery terminal | 6 kΩ or higher |
| CLEARANCE WARNING ECU ASSEMBLY (w/ Toyota Parking Assist-sensor System) |
Disconnect the cable from the negative (-) battery terminal.
Disconnect the clearance warning ECU assembly connector.

| *1 | DLC3 | - | - |
| *a | Front view of wire harness connector (to Clearance Warning ECU Assembly) | - | - |
Measure the resistance according to the value(s) in the table below.
| Terminal No. (Symbol) | Wiring Color | Terminal Description | Condition | Specified Condition |
| I82-17 (R1) - I82-18 (R2) | BE - W*1 P - W*2 | HIGH-level CAN bus line - LOW-level CAN bus line | Cable disconnected from negative (-) battery terminal | 54 to 69 Ω |
| I82-17 (R1) - I82-30 (E) | BE - BR*1 P - BR*2 | HIGH-level CAN bus line - Ground | Cable disconnected from negative (-) battery terminal | 200 Ω or higher |
| I82-18 (R2) - I82-30 (E) | W - BR | LOW-level CAN bus line - Ground | Cable disconnected from negative (-) battery terminal | 200 Ω or higher |
| I82-17 (R1) - I39-16 (BAT) | BE - R*1 P - R*2 | HIGH-level CAN bus line - Battery positive (+) | Cable disconnected from negative (-) battery terminal | 6 kΩ or higher |
| I82-18 (R2) - I39-16 (BAT) | W - R | LOW-level CAN bus line - Battery positive (+) | Cable disconnected from negative (-) battery terminal | 6 kΩ or higher |
| AFS ECU (w/ AFS) |

| *a | Component without harness connected (AFS ECU) | - | - |
Disconnect the cable from the negative (-) battery terminal.
Disconnect the AFS ECU connector.

| *1 | DLC3 | - | - |
| *a | Front view of wire harness connector (to AFS ECU) | - | - |
Measure the resistance according to the value(s) in the table below.
| Terminal No. (Symbol) | Wiring Color | Terminal Description | Condition | Specified Condition |
| A35-12 (MPX1) - A35-13 (MPX2) | B - W | HIGH-level CAN bus line - LOW-level CAN bus line | Cable disconnected from negative (-) battery terminal | 54 to 69 Ω |
| A35-12 (MPX1) - A35-22 (E1) | B - W-B | HIGH-level CAN bus line - Ground | Cable disconnected from negative (-) battery terminal | 200 Ω or higher |
| A35-13 (MPX2) - A35-22 (E1) | W - W-B | LOW-level CAN bus line - Ground | Cable disconnected from negative (-) battery terminal | 200 Ω or higher |
| A35-12 (MPX1) - I39-16 (BAT) | B - R | HIGH-level CAN bus line - Battery positive (+) | Cable disconnected from negative (-) battery terminal | 6 kΩ or higher |
| A35-13 (MPX2) - I39-16 (BAT) | W - R | LOW-level CAN bus line - Battery positive (+) | Cable disconnected from negative (-) battery terminal | 6 kΩ or higher |
| MULTIPLEX TILT AND TELESCOPIC ECU (w/ Power Tilt and Power Telescopic Steering Column System) |

| *a | Component without harness connected (Multiplex Tilt and Telescopic ECU) | - | - |
Disconnect the cable from the negative (-) battery terminal.
Disconnect the multiplex tilt and telescopic ECU connector.

| *a | Front view of wire harness connector (to Multiplex Tilt and Telescopic ECU) | - | - |
Measure the resistance according to the value(s) in the table below.
| Terminal No. (Symbol) | Wiring Color | Terminal Description | Condition | Specified Condition |
| I15-3 (CANP) -I15-11 (CANN) | B - GR | HIGH-level CAN bus line - LOW-level CAN bus line | Cable disconnected from negative (-) battery terminal | 54 to 69 Ω |
| I15-3 (CANP) - I15-1 (GND) | B - W-B | HIGH-level CAN bus line - Ground | Cable disconnected from negative (-) battery terminal | 200 Ω or higher |
| I15-11 (CANN) - I15-1 (GND) | GR - W-B | LOW-level CAN bus line - Ground | Cable disconnected from negative (-) battery terminal | 200 Ω or higher |
| I15-3 (CANP) - I15-2 (+B) | B - Y | HIGH-level CAN bus line - Battery positive (+) | Cable disconnected from negative (-) battery terminal | 6 kΩ or higher |
| I15-11 (CANN) - I15-2 (+B) | GR - Y | LOW-level CAN bus line - Battery positive (+) | Cable disconnected from negative (-) battery terminal | 6 kΩ or higher |