DTC B2610 Tilt Position Sensor or Tilt Motor Circuit Malfunction |

| DTC No. | Detection Item | Trouble Area |
| B2610 | Tilt operation stops within the operation range while operating. |
|

| 1.PERFORM ACTIVE TEST USING INTELLIGENT TESTER (TILT OPERATION) |
![]() |
Turn the engine switch off.
Connect the intelligent tester to the DLC3.
Turn the engine switch on (IG).
Turn the intelligent tester on.
Check that the steering wheel tilts up and down. Enter the following menus: Body / Tilt & Telescopic / Active Test.
| Tester Display | Test Part | Control Range | Diagnostic Note |
| Tilt Operation | Tilt operation | UP/DOWN | - |
| *a | Up |
| *b | Down |
|
| ||||
| OK | |
| 2.CHECK HARNESS AND CONNECTOR (MULTIPLEX TILT AND TELESCOPIC ECU - BATTERY) |
![]() |
Disconnect the I15 multiplex tilt and telescopic ECU connector.
Measure the voltage according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
| I15-2 (+B) - Body ground | Always | 11 to 14 V |
| *a | Front view of wire harness connector (to Multiplex Tilt and Telescopic ECU) |
|
| ||||
| OK | |
| 3.CHECK HARNESS AND CONNECTOR (MULTIPLEX TILT AND TELESCOPIC ECU - BODY GROUND) |
![]() |
Disconnect the I15 multiplex tilt and telescopic ECU connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
| I15-1 (GND) - Body ground | Always | Below 1 Ω |
| I15-8 (GND2) - Body ground | Always | Below 1 Ω |
| *a | Front view of wire harness connector (to Multiplex Tilt and Telescopic ECU) |
|
| ||||
| OK | |
| 4.CHECK HARNESS AND CONNECTOR (MULTIPLEX TILT AND TELESCOPIC ECU - TILT MOTOR) |
Disconnect the I15 multiplex tilt and telescopic ECU connector.
Disconnect the I23 tilt motor connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
| I15-7 (TIM+) - I23-2 (TIM+) | Always | Below 1 Ω |
| I15-20 (TIM-) - I23-1 (TIM-) | ||
| I15-7 (TIM+) - Body ground | 10 kΩ or higher | |
| I15-20 (TIM-) - Body ground |
|
| ||||
| OK | |
| 5.CHECK TILT MOTOR |
![]() |
Apply 12 V battery voltage to the tilt motor connector.
Then check the steering wheel tilt operation.
| Measurement Condition | Specified Condition |
| The steering wheel tilts down. |
| The steering wheel tilts up. |
| *a | Component without harness connected (Tilt Motor) |
|
| ||||
| OK | ||
| ||
| 6.CHECK HARNESS AND CONNECTOR (MULTIPLEX TILT AND TELESCOPIC ECU - TILT POSITION SENSOR) |
Disconnect the I15 multiplex tilt and telescopic ECU connector.
Disconnect the I23 tilt motor connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
| I15-13 (VCI) - I23-4 (VCI) | Always | Below 1 Ω |
| I15-16 (TIS) - I23-5 (TIS) | ||
| I15-4 (E1) - I23-6 (E1) | ||
| I15-13 (VCI) - Body ground | 10 kΩ or higher | |
| I15-16 (TIS) - Body ground | ||
| I15-4 (E1) - Body ground |
|
| ||||
| OK | |
| 7.CHECK HARNESS AND CONNECTOR (MULTIPLEX TILT AND TELESCOPIC ECU - BODY GROUND) |
![]() |
Disconnect the I15 multiplex tilt and telescopic ECU connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
| I15-1 (GND) - Body ground | Always | Below 1 Ω |
| I15-8 (GND2) - Body ground | Always | Below 1 Ω |
| *a | Front view of wire harness connector (to Multiplex Tilt and Telescopic ECU) |
|
| ||||
| OK | |
| 8.CHECK MULTIPLEX TILT AND TELESCOPIC ECU (VCI, TIS TERMINAL VOLTAGE) |
![]() |
Disconnect the I23 tilt motor connector.
Reconnect the I15 multiplex tilt and telescopic ECU connector.
Measure the voltage according to the value(s) in the table below.
| Tester Connection | Switch Condition | Specified Condition |
| I15-13 (VCI) - I15-4 (E1) | Engine switch on (IG) | 8 to 16 V |
| I15-16 (TIS) - I15-4 (E1) |
| *a | Component with harness connected (Multiplex Tilt and Telescopic ECU) |
|
| ||||
| OK | |
| 9.CHECK TILT POSITION SENSOR |
![]() |
Reconnect the I15 multiplex tilt and telescopic ECU connector.
Reconnect the I23 tilt motor connector.
Measure the voltage according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
| I15-16 (TIS) - I15-4 (E1) | Steering wheel tilting up or tilting down | Pulse generation High: 8 to 16 V Low: Below 1 V |
| *a | Component with harness connected (Multiplex Tilt and Telescopic ECU) |
|
| ||||
| OK | ||
| ||