Home › Steering › STEERING COLUMN › POWER TILT AND POWER TELESCOPIC STEERING COLUMN SYSTEM

POWER TILT AND POWER TELESCOPIC STEERING COLUMN SYSTEM > FREEZE FRAME DATA

for Preparation Click here



FREEZE FRAME DATA

NOTICE:
  1. Freeze frame data values will vary depending on the measurement conditions, surroundings, or vehicle conditions. For this reason, there may be a problem even when the values are within specifications.
  2. Turn the engine switch on (IG) and park the vehicle on level ground. Check the freeze frame data by using the intelligent tester.

  1. Turn the engine switch off.

  2. Connect the intelligent tester to the DLC3.

  3. Turn the engine switch on (IG).

  4. Turn the intelligent tester on.

  5. Check the freeze frame data. Enter the following menus: Body / Tilt & Telescopic / Trouble Codes.

    Tilt & Telescopic 
    Tester Display
    Measurement Item/Range
    Normal Condition
    Diagnostic Note
    Tilt Position
    Current tilt position data/
    Min.: 0
    Max.: 65535
    28672 to 36864
    -
    Telesco Position
    Current telescopic position data/
    Min.: 0
    Max.: 65535
    28672 to 36864
    -
    Tilt Return Position
    Memorized tilt return position data/
    Min.: 0
    Max.: 65535
    28672 to 36864
    -
    Telesco Return Position
    Memorized telescopic return position data/
    Min.: 0
    Max.: 65535
    28672 to 36864
    -
    Tilt Up Switch
    Input state of tilt up switch/
    ON or OFF
    ON: Tilt up switch activated
    OFF: Tilt up switch not activated
    -
    Tilt Up SW (CAN)
    Input state of tilt up by switch/
    ON or OFF
    -
    (This item is not related to this vehicle)
    Tilt Down Switch
    Input state of tilt down switch/
    ON or OFF
    ON: Tilt down switch activated
    OFF: Tilt down switch not activated
    -
    Tilt Down SW (CAN)
    Input state of tilt down switch/
    ON or OFF
    -
    (This item is not related to this vehicle)
    Telesco Short Switch
    Input state of telescopic contract switch/
    ON or OFF
    ON: Telescopic contract switch activated
    OFF: Telescopic contract switch not activated
    -
    Telesco Short SW (CAN)
    Input state of telescopic contract switch/
    ON or OFF
    -
    (This item is not related to this vehicle)
    Telesco Long Switch
    Input state of telescopic extend switch/
    ON or OFF
    ON: Telescopic extend switch activated
    OFF: Telescopic extend switch not activated
    -
    Telesco Long SW (CAN)
    Input state of telescopic extend switch/
    ON or OFF
    -
    (This item is not related to this vehicle)
    T&T Manual SW Data
    Voltage data of tilt and telescopic switch/
    Min.: 0.00 V
    Max.: 4.99 V
    Neutral position: Below 0.2 V
    Tilt up: 1.67 to 2.13 V
    Tilt down: 0.54 to 0.74 V
    Telescopic contract: 1.08 to 1.40 V
    Telescopic extend: 2.22 to 2.77 V
    -
    Power Source Voltage
    Voltage data of power supply/
    Min.: 0.00 V
    Max.: 19.99 V
    11 to 14 V
    -
    Freeze Speed Info
    Vehicle speed data/
    Min.: 0 km/h (0 mph)
    Max.: 255 km/h (158 mph)
    Actual vehicle speed
    -
    IG Switch (CAN)
    Communication state of engine switch/
    ON or OFF
    ON: Communication normal
    OFF: Communication interrupted
    -
    IG Switch
    Input state of engine switch/
    ON or OFF
    ON: Input signal normal
    OFF: Input signal interrupted
    -
    Receive from Meter
    Communication state of combination meter assembly signal/
    OK or Interpt
    OK: Communication normal
    Interpt: Communication interrupted
    -
    Receive from Seat ECU
    Communication state of position control ECU signal/
    OK or Interpt
    OK: Communication normal
    Interpt: Communication interrupted
    (This item is not related to this vehicle)
    Receive from Combi
    Communication state of combination switch ECU signal/
    OK or Interpt
    OK: Communication normal
    Interpt: Communication interrupted
    (This item is not related to this vehicle)
    J/B
    Communication state of main body ECU (multiplex network body ECU) signal/
    OK or Interpt
    OK: Communication normal
    Interpt: Communication interrupted
    -
    Handle Position
    Steering wheel position signal/
    Away or Return
    Away: Steering wheel in away position
    Return: Steering wheel in return position
    -
    The Number of DTCs
    Number of stored DTCs/
    Min.: 0
    Max.: 255
    Actual number of stored DTCs
    -