ENGINE ASSEMBLY > INSTALLATION |
| 1. REMOVE ENGINE STAND |
Using a chain block and engine sling device, secure the engine assembly.
Remove the engine stand from the engine assembly.
| 2. INSTALL DRIVE PLATE AND RING GEAR SUB-ASSEMBLY |
![]() |
Using SST, hold the crankshaft.
Clean the bolts and their installation holes.
![]() |
Install the front drive plate spacer.
![]() |
Install the drive plate and ring gear sub-assembly and rear drive plate spacer to the crankshaft.
| *1 | Drive Plate And Ring Gear Sub-assembly |
| *2 | Rear Drive Plate Spacer |
![]() | Transaxle Side |
![]() |
Apply adhesive to 2 or 3 threads at the end of each of the 8 bolts.
| *1 | Adhesive |
![]() |
Install and uniformly tighten the 8 bolts in several steps in the sequence shown in the illustration.
| 3. INSTALL AUTOMATIC TRANSAXLE ASSEMBLY |
![]() |
Apply clutch spline grease to the surface of the crankshaft that contacts the torque converter assembly centerpiece.
| *1 | Crankshaft |
| *2 | Torque Converter Assembly Centerpiece |
![]() |
While keeping the engine and automatic transaxle assembly horizontal, align the knock pins with the holes in the automatic transaxle assembly and install the 9 bolts shown in the illustration.
| 4. INSTALL ENGINE WIRE |
Connect the 4 connectors and 6 clamps, and install the engine wire to the automatic transaxle assembly with the bolt.
| 5. INSTALL ENGINE MOUNTING BRACKET RH |
Install the engine mounting bracket RH with the 3 bolts.
| 6. INSTALL DRIVE SHAFT BEARING BRACKET |
Install the drive shaft bearing bracket with the 3 bolts.
| 7. TEMPORARILY INSTALL FRONT ENGINE MOUNTING INSULATOR |
Temporarily install the front engine mounting insulator with the 3 nuts.
| 8. TEMPORARILY INSTALL ENGINE MOUNTING INSULATOR LH |
Temporarily install the engine mounting insulator LH with the 3 nuts.
| 9. TEMPORARILY INSTALL ENGINE MOUNTING INSULATOR RH |
Temporarily install the engine mounting insulator RH with the 3 nuts.
| 10. INSTALL FRONT FRAME ASSEMBLY |
Install the engine mounting insulator LH to the automatic transaxle assembly with the nut.
Install the engine mounting insulator RH to the engine with the nut.
Install the front engine mounting insulator to the automatic transaxle assembly with the bolt.
Fully tighten the 9 temporarily installed nuts of the engine mounting insulators to the specified torque.

| *a | Front Engine Mounting Insulator Side | *b | Engine Mounting Insulator RH Side |
| *c | Engine Mounting Insulator LH Side | - | - |
Install the 4 hole plugs.
| 11. INSTALL GENERATOR ASSEMBLY |
![]() |
Install the generator assembly with the 2 bolts.
Install the wire harness clamp bracket with the bolt.
Install the generator wire to terminal B with the nut.
Install the terminal cap.
Connect the connector and wire harness clamp.
| 12. INSTALL COMPRESSOR ASSEMBLY WITH PULLEY |
![]() |
Install the compressor assembly with pulley with the 4 bolts.
| 13. INSTALL V-RIBBED BELT |
![]() |
Set the V-ribbed belt onto each part as shown in the illustration.
| *1 | V-ribbed Belt Tensioner Assembly |
| *2 | Generator |
| *3 | Water Pump |
| *4 | Cooler Compressor |
| *5 | Crankshaft |
| *6 | Idler |
Using SST, slowly turn the V-ribbed belt tensioner assembly clockwise and install the V-ribbed belt.
| 14. INSTALL ENGINE ASSEMBLY WITH TRANSAXLE |
Install the engine wire to the engine with transaxle.
Set the engine assembly with transaxle on an engine lifter.
Remove the engine hangers .
Install the engine assembly with transaxle to the vehicle.
![]() |
Install the frame side rail plate RH and LH with the 4 bolts and 2 nuts.
Install the front suspension member brace rear RH and LH with the 4 bolts and 2 nuts.
| 15. INSTALL DRIVE PLATE AND TORQUE CONVERTER ASSEMBLY SETTING BOLT |
![]() |
Apply adhesive to 2 or 3 threads at the tip of each of the 6 drive plate and torque converter assembly setting bolts.
| *1 | Adhesive |
![]() |
Turn the crankshaft to gain access to the installation locations of the 6 drive plate and torque converter assembly setting bolts and install each bolt while holding the crankshaft pulley bolt with a wrench.
| 16. INSTALL FLYWHEEL HOUSING UNDER COVER |
Install the flywheel housing under cover.
| 17. CONNECT STEERING INTERMEDIATE SHAFT ASSEMBLY |
![]() |
Align the matchmarks and install the steering intermediate shaft to the steering link assembly.
| *a | Matchmark |
Install the bolt.
| 18. INSTALL FRONT DRIVE SHAFT ASSEMBLY |
| 19. INSTALL FRONT EXHAUST PIPE ASSEMBLY |
![]() |
Using a vernier caliper, measure the free length of the compression springs.
| Minimum | 40.5 mm (1.59 in.) |
Fully insert a new gasket to the exhaust manifold converter sub-assembly.
![]() |
Using a plastic hammer and wooden block, tap in the new gasket until its surface is flush with the exhaust manifold converter sub-assembly.
| *1 | Exhaust Manifold Converter Sub-assembly |
| *2 | Gasket |
| *3 | Wooden Block |
Install a new gasket to the front exhaust pipe assembly.
Install the front exhaust pipe assembly with the 2 bolts, 2 nuts and 2 compression springs.
Connect the oxygen sensor connector.
| 20. CONNECT FUEL TUBE SUB-ASSEMBLY |
![]() |
Push the fuel tube connector to the fuel pipe until the fuel tube connector makes a "click" sound.
| *1 | Fuel Pipe |
| *2 | Fuel Tube Connector |
| *3 | Nylon Tube |
| *4 | O-ring |
| *5 | Retainer |
Install the fuel tube sub-assembly to the fuel hose clamp.
Install the No. 1 fuel pipe clamp.
| 21. INSTALL NO. 1 COOLER REFRIGERANT SUCTION HOSE |
Remove the attached vinyl tape from the hose.
Apply sufficient compressor oil to a new O-ring and the fitting surface of the compressor assembly with pulley.
Install the O-ring to the No. 1 cooler refrigerant suction hose.
Install the No. 1 cooler refrigerant suction hose onto the compressor assembly with pulley with the bolt.
| 22. INSTALL NO. 1 COOLER REFRIGERANT DISCHARGE HOSE |
Remove the attached vinyl tape from the hose.
Apply sufficient compressor oil to a new O-ring and the fitting surface of the compressor assembly with pulley.
Install the O-ring onto the No. 1 cooler refrigerant discharge hose.
Install the No. 1 cooler refrigerant discharge hose onto the compressor assembly with pulley with the bolt.
Install the bracket with the bolt.
Connect the 2 connectors.
Engage the 2 clamps.
| 23. CONNECT TRANSMISSION CONTROL CABLE ASSEMBLY |
Connect the transmission control cable assembly to the control cable support.
Connect the transmission control cable assembly to the transmission control cable bracket with a new clip.
Connect the transmission control cable assembly to the control shaft lever with the nut.
| 24. CONNECT ENGINE WIRE |
![]() |
Connect the wire harness clamp.
![]() |
Connect the wire harness clamp and install the bolt.
![]() |
Engage the claw to install the engine wire.
Connect the 4 connectors and install the nut.
Connect the 2 wire harness clamps, ECM connector and lower the lever.
Install the No. 1 relay block cover.
| 25. INSTALL STARTER ASSEMBLY |
Install the starter assembly with the 2 bolts.
Connect the connector.
Connect the starter wire and install the nut, close the terminal cap.
| 26. CONNECT OUTLET HEATER WATER HOSE |
Connect the outlet heater water hose.
| 27. CONNECT INLET HEATER WATER HOSE |
Connect the inlet heater water hose and breather.
| 28. CONNECT INLET NO. 1 OIL COOLER HOSE |
Connect the inlet No. 1 oil cooler hose to the automatic transaxle assembly.
| 29. CONNECT OUTLET NO. 1 OIL COOLER HOSE |
Connect the outlet No. 1 oil cooler hose to the automatic transaxle assembly.
| 30. CONNECT NO. 2 RADIATOR HOSE |
Connect the No. 2 radiator hose.
| 31. CONNECT NO. 1 RADIATOR HOSE |
Connect the No. 1 radiator hose and wire harness clamp.
| 32. CONNECT UNION TO VACUUM TUBE HOSE |
Connect the union to vacuum tube hose to the intake manifold.
| 33. INSTALL NO. 2 ENGINE MOUNTING BRACKET RH |
Install the No. 2 engine mounting bracket RH with the 3 bolts.
| 34. INSTALL ENGINE MOVING CONTROL ROD SUB-ASSEMBLY |
![]() |
Install the engine moving control rod sub-assembly with the 3 bolts.
| 35. INSTALL NO. 2 ENGINE MOUNTING STAY RH |
Install the No. 2 engine mounting stay RH with the 2 bolts.
| 36. INSTALL AIR CLEANER CASE SUB-ASSEMBLY |
Install the air cleaner case sub-assembly with the 3 bolts.
Connect the wire harness clamp.
| 37. INSTALL AIR CLEANER CAP SUB-ASSEMBLY |
Install the air cleaner filter element to the air cleaner case sub-assembly.
![]() |
Connect the air cleaner cap sub-assembly to the throttle with motor body assembly and release the lock of the air cleaner hose clamp.
| *1 | Air Cleaner Hose Clamp |
Connect the ventilation hose to the cylinder head cover.
Install the air cleaner cap sub-assembly and tighten the 2 bolts.
Connect the wire harness clamp.
Connect the mass air flow meter connector.
Connect the purge line hose to the 2 clamps.
Connect the 2 vacuum switching valve vacuum hoses.
Connect the vacuum switching valve connector.
| 38. INSTALL INLET AIR CLEANER ASSEMBLY |
Install the inlet air cleaner assembly with the 2 bolts.
| 39. INSTALL FRONT OUTER COWL TOP PANEL SUB-ASSEMBLY |
Install the front outer cowl top panel sub-assembly with the 10 bolts.
Engage the 2 clamps to install the wire harness to the front outer cowl top panel sub-assembly.
| 40. INSTALL WINDSHIELD WIPER MOTOR AND LINK ASSEMBLY |
| 41. CONNECT CABLE TO NEGATIVE BATTERY TERMINAL |
| 42. ADD ENGINE OIL |
Add new engine oil.
| Oil Grade | Oil Viscosity (SAE) |
| API grade SL "Energy-Conserving", SM "Energy-Conserving", SN "Resource-Conserving" or ILSAC multigrade engine oil |
|
| API grade SL, SM or SN multigrade engine oil |
|
| Item | Standard Condition |
| Drain and refill with oil filter change | 4.3 liters (4.5 US qts., 3.8 Imp. qts.) |
| Drain and refill without oil filter change | 4.1 liters (4.3 US qts., 3.6 Imp. qts.) |
| Dry fill | 5.0 liters (5.3 US qts., 4.4 Imp. qts.) |
Install the oil filler cap.
| 43. ADD ENGINE COOLANT |
Tighten the radiator drain cock plug by hand.
Tighten the cylinder block drain cock plug.
Slowly fill the radiator with TOYOTA Super Long Life Coolant (SLLC).
Slowly pour engine coolant into the radiator reserve tank assembly until it reaches the full line.
Squeeze the No. 1 and No. 2 radiator hoses several times by hand, and then check the level of the engine coolant.
If the engine coolant level is low, add engine coolant.
Install the radiator cap sub-assembly and reserve tank cap.
Bleed air from the cooling system.
Warm up the engine until the thermostat opens. While the thermostat is open, circulate the engine coolant for several minutes.
Maintain the engine speed at 2000 to 2500 rpm.
Squeeze the No. 1 and No. 2 radiator hoses several times by hand to bleed air.
Stop the engine and wait until the engine coolant cools down.
Add engine coolant to the full line on the radiator reserve tank assembly.
| 44. ADD AUTOMATIC TRANSAXLE FLUID |
| 45. CHARGE AIR CONDITIONING SYSTEM WITH REFRIGERANT |
Perform vacuum purging using a vacuum pump or appropriate equipment.
Charge the air conditioning system with refrigerant.

| *a | Sub-cool System | *b | High Pressure |
| *c | Refrigerant Amount | *d | Standard charge amount |
| *e | Charge additional 100 g (3.5 oz.) | *f | Point where bubbles disappear |
| *g | Mean value in proper range | *h | Overcharged |
| 46. WARM UP ENGINE |
Keep the A/C switch on for at least 2 minutes to warm up the compressor.
| 47. INSPECT FOR FUEL LEAK |
Check fuel pump operation.
Connect the intelligent tester to the DLC3.
Turn the ignition switch to ON and turn the intelligent tester on.
Enter the following menus: Powertrain / Engine and ECT / Active Test / Control the Fuel Pump / Speed.
Check for pressure in the fuel tube sub-assembly from the fuel line. Check that sounds of fuel flowing from the fuel tank assembly can be heard. If no sounds can be heard, check the integration relay, fuel pump, ECM and wiring connectors.
Inspect for fuel leaks.
Check that there are no fuel leaks from the fuel system after doing any maintenance or repairs. If there is a fuel leak, repair or replace parts as necessary.
Turn the ignition switch off.
Disconnect the intelligent tester from the DLC3.
| 48. INSPECT FOR COOLANT LEAK |
![]() |
Fill the radiator assembly with engine coolant and attach a radiator cap tester.
Warm up the engine.
Using a radiator cap tester, increase the pressure inside the radiator assembly to 118 kPa (1.2 kgf/cm2, 17 psi), and check that the pressure does not drop.
If the pressure drops, check the hoses, radiator assembly and engine water pump assembly for leaks. If no external leaks are found, check the heater core, cylinder block and cylinder head.
| 49. INSPECT FOR REFRIGERANT LEAK |
After recharging the air conditioning system with refrigerant, inspect for refrigerant leaks using a halogen leak detector.
Carry out the test under the following conditions:
![]() |
Using a halogen leak detector, inspect for refrigerant leaks from the air conditioning system.
| *1 | Halogen Leak Detector |
| *a | Inspect for Leak |
![]() |
Bring the halogen leak detector close to the drain hose with the detector power off, and then turn the detector on.
| *1 | Halogen Leak Detector |
| *2 | Drain Hose |
If a refrigerant leak is not detected from the drain hose, remove the blower motor control from the cooling unit. Insert the halogen leak detector sensor into the unit and check for a leak.
Disconnect the pressure sensor connector and leave it for approximately 20 minutes. Bring the halogen leak detector close to the pressure sensor and check for a leak.
| 50. INSPECT AUTOMATIC TRANSMISSION FLUID LEVEL |
![]() |
Park the vehicle on a level surface and apply the parking brake.
| *a | OK if hot |
| *b | Add if hot |
With the engine idling and the brake pedal depressed, move the shift lever to all positions from P to L. Then return it to P.
Pull out the dipstick and wipe it clean.
Push the dipstick back fully into the pipe.
Pull the dipstick out again and check that the fluid level is within the HOT range. If the fluid level is below the HOT range, add new fluid and recheck the fluid level. If the fluid level exceeds the HOT range, drain the fluid once, add a proper amount of new fluid and recheck the fluid level.
| 51. INSPECT FOR OIL LEAK |
| 52. INSPECT FOR EXHAUST GAS LEAK |
| 53. INSPECT IGNITION TIMING |
Warm up and stop the engine.
When using the intelligent tester:
Connect the intelligent tester to the DLC3.
Start the engine and idle it.
Turn the intelligent tester main switch on.
Enter the following menus: Powertrain / Engine / Data List / IGN Advance.
Check that the ignition timing advances immediately when the engine speed is increased.
Enter the following menus: Powertrain / Engine / Active Test / Connect the TC and TE1 / ON.
Monitor IGN Advance of the Data List.
Enter the following menus: Powertrain / Engine / Active Test / Connect the TC and TE1 / OFF.
Turn the ignition switch off.
Disconnect the intelligent tester from the DLC3.
When not using the intelligent tester:
![]() |
Open the wiring harness protector cover located to the right of the No. 4 ignition coil.
Pull the wire harness out from the wiring harness protector cover.
Connect the timing light to the wire harness.
![]() |
Using SST, connect terminals 13 (TC) and 4 (CG) of the DLC3.
| *a | DLC3 |
Using a timing light, check the ignition timing.
Remove SST from the DLC3.
Check the ignition timing.
Check that the ignition timing advances immediately when the engine speed is increased.
Disconnect the timing light from the engine.
Install the No. 1 engine cover sub-assembly.
| 54. INSPECT ENGINE IDLE SPEED |
Warm up and stop the engine.
When using the intelligent tester:
Connect the intelligent tester to the DLC3.
Race the engine at 2500 rpm for approximately 90 seconds.
Turn the intelligent tester main switch on.
Enter the following menus: Powertrain / Engine / Data List / Engine Speed.
Disconnect the intelligent tester from the DLC3.
When not using the intelligent tester:
![]() |
Using SST, connect a tachometer probe to terminal 9 (TAC) of the DLC3.
| *a | DLC3 |
Race the engine at 2500 rpm for approximately 90 seconds.
Check the idle speed.
Disconnect the tachometer probe from the DLC3.
| 55. INSPECT CO/HC |
Start the engine.
Keep the engine speed at 2500 rpm for approximately 180 seconds.
Insert the CO/HC meter testing probe at least 40 cm (1.31 ft.) into the tailpipe during idling.
Immediately check CO/HC concentration at idle and 2500 rpm.
Check the DTCs (Click here).
See the table below for possible causes, and then inspect and correct the applicable parts if necessary.
| CO | HC | Symptom | Causes |
| Normal | High | Rough idle |
|
| Low | High | Rough idle (Fluctuating HC reading) |
|
| High | High | Rough idle (Black smoke from exhaust) |
|
| 56. INSTALL NO. 1 ENGINE COVER SUB-ASSEMBLY |
Install the No. 1 engine cover sub-assembly with the 2 nuts.
| 57. INSTALL COOL AIR INTAKE DUCT SEAL |
Install the cool air intake duct seal with the 9 clips.
| 58. INSPECT SHIFT LEVER POSITION |
When the shift lever is moved from P to R with the ignition switch ON and brake pedal depressed, make sure that the shift lever moves smoothly and correctly into the position.
Start the engine and make sure that the vehicle moves forward when the shift lever is moved from N to D and moves rearward when the shift lever is moved to R.