Home › Engine / Hybrid System · 2AR-FE › STARTING › STARTER (for 1.6 kW Type)

STARTER (for 1.6 kW Type) > INSPECTION

for Preparation Click here



1. INSPECT STARTER ASSEMBLY

CAUTION:
As a large electric current passes through the cable during this inspection, a thick cable must be used. If not, the cable may became hot and cause injury.

NOTICE:
These tests must be performed within 3 to 5 seconds to avoid burning out the coil.



  1. Perform a pull-in test.

    1. Disconnect the lead wire from terminal C.



    2. A197192E03
    3. Connect the battery to the magnet starter switch as shown in the illustration. Check that the clutch pinion gear extends.
      Text in Illustration 
      *1
      Terminal 50
      *2
      Terminal C
      *3
      Body
      If the clutch pinion gear does not move, replace the magnet starter switch assembly.



    A197193E03
  1. Perform the holding test.

    1. Maintain the battery connections of the pull-in test above, but disconnect the negative (-) lead from terminal C. Check that the pinion gear remains extended.
      Text in Illustration 
      *1
      Terminal 50
      *2
      Terminal C
      *3
      Body
      If the clutch pinion gear returns inward, replace the magnet starter switch assembly.



    A197194E02
  1. Check the clutch pinion gear return.

    1. Disconnect the negative (-) lead from the starter body. Check that the clutch pinion gear returns inward.
      If the clutch pinion gear does not return, replace the magnet starter switch assembly.
      Text in Illustration 
      *1
      Terminal 50
      *2
      Terminal C
      *3
      Body



    A197195E03
  1. Perform a no-load performance test.

    1. Connect the lead wire to terminal C with the nut. Make sure that the lead is not grounded.

      Torque:
      10 N*m{ 102 kgf*cm , 7 ft.*lbf }

      Text in Illustration 
      *1
      Terminal 30
      *2
      Terminal 50

    2. Clamp the starter in a vise.

    3. Connect the battery and an ammeter to the starter as shown in the illustration.

    4. Check that the starter rotates smoothly and steadily while the pinion gear is moving out. Then measure the current.

      Standard current:
      90 A or less at 11.5 V

      If the result is not as specified, replace the starter assembly.



2. INSPECT STARTER CLUTCH


    A197200E03
  1. Check the starter clutch.

    1. Rotate the clutch pinion gear counterclockwise and check that it turns freely. Try to rotate the clutch pinion gear clockwise and check that it locks.
      Text in Illustration 
      *a
      Lock
      *b
      Free
      If necessary, replace the repair service starter kit.



3. INSPECT MAGNET STARER SWITCH ASSEMBLY


    A197181
  1. Inspect the plunger.

    1. Push in the plunger and check that it returns quickly to its original position.
      If necessary, replace the magnet starter switch assembly.



    A197182E07
  1. Inspect the pull-in coil.

    1. Measure the resistance according to the value(s) in the table below.

      Standard Resistance:
      Tester Connection
      Condition
      Specified Condition
      Terminal 50 - Terminal C
      Always
      Below 1 Ω
      Text in Illustration 
      *1
      Terminal 50
      *2
      Terminal C

      If the result is not as specified, replace the magnet starter switch assembly.



    A197183E09
  1. Inspect the holding coil.

    1. Measure the resistance according to the value(s) in the table below.

      Standard Resistance:
      Tester Connection
      Condition
      Specified Condition
      Terminal 50 - Switch body
      Always
      Below 2 Ω
      Text in Illustration 
      *1
      Terminal 50
      *2
      Body

      If the result is not as specified, replace the magnet starter switch assembly.



4. INSPECT STARTER ARMATURE ASSEMBLY


  1. Inspect the commutator for an open circuit.



      A058372E21
    1. Measure the resistance according to the value(s) in the table below.

      Standard Resistance:
      Tester Connection
      Condition
      Specified Condition
      Segment - Segment
      Always
      Below 1 Ω
      Text in Illustration 
      *1
      Segment

      If the result is not as specified, replace the starter armature assembly.



  1. Inspect the commutator for a short circuit.



      A058373E17
    1. Measure the resistance according to the value(s) in the table below.

      Standard Resistance:
      Tester Connection
      Condition
      Specified Condition
      Commutator - Armature coil core
      Always
      10 kΩ or higher
      Text in Illustration 
      *1
      Commutator
      *2
      Armature coil core

      If the result is not as specified, replace the starter armature assembly.

  1. Check the surface of the commutator for dirt and burns.
    If the surface is dirty or burnt, correct it with sandpaper (No. 400) or a lathe.



    A194765E03
  1. Using a vernier caliper, measure the commutator length.
    Text in Illustration 
    *a
    Length

    Standard length:
    3.1 to 3.8 mm (0.122 to 0.150 in.)

    If the length is more than the maximum, replace the starter armature assembly.



5. INSPECT STARTER COMMUTATOR END FRAME ASSEMBLY


    A194766E03
  1. Using a vernier caliper, measure the brush length.
    Text in Illustration 
    *a
    Length

    Standard length:
    4.0 to 9.0 mm (0.158 to 0.359 in.)

    If the length is less than the minimum, replace the starter commutator end frame assembly.



    A197190
  1. Inspect the insulation.

    1. Measure the resistance according to the value(s) in the table below.

      Standard Resistance:
      Tester Connection
      Condition
      Specified Condition
      Positive (+) brush - Negative (-) brush
      Always
      10 kΩ or higher

      If the result is not as specified, repair or replace the starter commutator end frame assembly.