Home › Engine / Hybrid System · 1AZ-FE › STARTING › STARTER

STARTER > INSPECTION

for Preparation Click here



1. INSPECT STARTER ASSEMBLY

CAUTION:
As a large electric current passes through the cable during this inspection, a thick cable must be used. If not, the cable may became hot and cause injury.

NOTICE:
These tests must be performed within 3 to 5 seconds to avoid burning out the coil.



  1. Perform a pull-in test.

    1. Remove the nut and disconnect the lead wire from terminal C.



    2. A193954E02
    3. Connect the battery to the magnet switch as shown in the illustration. Check that the clutch pinion gear extends.
      Text in Illustration 
      *1
      Terminal 50
      *2
      Terminal C
      If the clutch pinion gear does not move, replace the magnet starter switch assembly.



  1. Perform a hold-in test.



      A081044E11
    1. While maintaining the battery connections of the pull-in test above, disconnect the negative (-) lead from terminal C. Check that the pinion gear remains extended.
      Text in Illustration 
      *1
      Disconnect
      *2
      Terminal C
      If the clutch pinion gear returns inward, replace the magnet starter switch assembly.



  1. Perform a clutch pinion gear return test.



      A081045E06
    1. Disconnect the negative (-) lead from the starter body. Check that the clutch pinion gear returns inward.
      Text in Illustration 
      *1
      Disconnect
      If the clutch pinion gear does not return inward, replace the magnet starter switch assembly.



  1. Perform a no-load performance test.

    1. Connect the lead wire to terminal C with the nut. Make sure that the lead wire is not grounded.

      Torque:
      10 N*m{ 102 kgf*cm , 7 ft.*lbf }

    2. Hold the starter assembly in a vise between aluminum plates.

      NOTICE:
      Ensure that the starter assembly is secured firmly in the vise to prevent it from falling out.



    3. A060462E08
    4. Connect the battery and an ammeter to the starter assembly as shown in the illustration.
      Text in Illustration 
      *1
      Terminal 30
      *2
      Terminal 50

      NOTICE:
      Do not allow any lead to get caught as the pinion gear operates.

    5. Check that the starter assembly rotates smoothly and steadily while the pinion gear is moving out. Then measure the current.

      Standard current:
      90 A or less at 11.5 V

      If the result is not as specified, repair or replace the starter assembly.



2. INSPECT MAGNET STARTER SWITCH ASSEMBLY


  1. Check the plunger.



      A058586
    1. Push in the plunger and check that it returns quickly to its original position.
      If necessary, replace the magnet starter switch assembly.



  1. Check if the pull-in coil has an open circuit.



      A079725E17
    1. Measure the resistance between terminals 50 and C.
      Text in Illustration 
      *1
      Terminal C
      *2
      Terminal 50

      Standard resistance:
      Below 1 Ω

      If the result is not as specified, replace the magnet starter switch assembly.



  1. Check if the hold-in coil has an open circuit.



      A079726E14
    1. Measure the resistance between terminal 50 and the magnet switch body.
      Text in Illustration 
      *1
      Terminal 50
      *2
      Magnet Switch Body

      Standard resistance:
      Below 2 Ω

      If the result is not as specified, replace the magnet starter switch assembly.



3. INSPECT STARTER ARMATURE ASSEMBLY

HINT:
If these is no continuity between any segments, replace the starter armature assembly.

  1. Check the commutator for contamination and burns on its surface.
    If the surface is dirty or burnt, correct it with sandpaper (No. 400) or a lathe.



  1. Check if the commutator has an open circuit.



      A058372E15
    1. Measure the resistance between the segments of the commutator.
      Text in Illustration 
      *1
      Segment

      Standard resistance:
      Below 1 Ω

      If the result is not as specified, replace the starter armature assembly.



  1. Check if the commutator is grounded.



      A058373E10
    1. Measure the resistance between the commutator and armature coil core.
      Text in Illustration 
      *1
      Segment
      *2
      Armature Coil Core

      Standard resistance:
      10 kΩ or higher

      If the result is not as specified, replace the starter armature assembly.



    A058584E22
  1. Using a vernier caliper, measure the commutator length.
    Text in Illustration 
    *a
    Length

    Standard length:
    3.1 mm (0.122 in.)

    Maximum length:
    3.8 mm (0.150 in.)

    If the length is greater than the maximum, replace the starter armature assembly.



4. INSPECT STARTER COMMUTATOR END FRAME ASSEMBLY


    A076677E19
  1. Using a vernier caliper, measure the brush length.
    Text in Illustration 
    *a
    Length

    Standard length:
    9.0 mm (0.354 in.)

    Minimum length:
    4.0 mm (0.157 in.)

    If the length is less than the minimum, replace the starter commutator end frame assembly.



    A079766E14
  1. Check the brush insulation.

    1. Measure the resistance between the positive (+) and negative (-) brushes.

      Standard resistance:
      10 kΩ or higher

      If the result is not as specified, replace the starter commutator end frame assembly.



5. INSPECT STARTER CLUTCH


    A081655E13
  1. Rotate the clutch pinion gear counterclockwise and check that it turns freely. Try to rotate the clutch pinion gear clockwise and check that it locks.
    Text in Illustration 
    *a
    Lock
    *b
    Free
    If necessary, replace the repair service starter kit.