Home › Engine / Hybrid System · CRUISE CONTROL › CRUISE CONTROL SYSTEM

DTC    P0571    Brake Switch "A" Circuit

for Preparation Click here


DESCRIPTION

When the brake pedal is depressed, the stop light switch assembly sends a signal to the ECM. When the ECM receives this signal, it cancels cruise control system control of vehicle speed. The fail-safe function operates to enable normal driving even if there is a malfunction in the stop light signal circuit. The cancellation condition occurs when voltage is applied to terminal STP. When the brake is applied, voltage is normally applied to terminal STP of the ECM through the STOP fuse and the stop light switch assembly, and the ECM cancels control of vehicle speed by the cruise control system.

DTC No.
DTC Detection Condition
Trouble Area
P0571
When voltage of STP terminal and that of ST1- terminal of ECM are less than 1 V for 0.5 sec. or more
  1. Stop light switch assembly
  2. Stop light switch circuit
  3. ECM

WIRING DIAGRAM


E236799E03


E236800E04


INSPECTION PROCEDURE

NOTICE:
Inspect the fuses for circuits related to this system before performing the following inspection procedure.

1.INSPECT STOP LIGHT SWITCH ASSEMBLY (POWER SOURCE)


    E144327E14
  1. Disconnect the stop light switch assembly connector.

  1. Measure the voltage according to the value(s) in the table below.

    Standard Voltage:
    Tester Connection
    Condition
    Specified Condition
    A33-2 - Body ground
    Always
    11 to 14 V

    Text in Illustration 
    *a
    Front view of wire harness connector
    (to Stop Light Switch Assembly)

  1. Reconnect the stop light switch assembly connector.



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR (STOP LIGHT SWITCH ASSEMBLY - BATTERY)
OK


2.INSPECT STOP LIGHT SWITCH ASSEMBLY (POWER SOURCE)


    E144327E14
  1. Disconnect the stop light switch assembly connector.

  1. Measure the voltage according to the value(s) in the table below.

    Standard Voltage:
    Tester Connection
    Switch Condition
    Specified Condition
    A33-4 - Body ground
    Ignition switch ON
    11 to 14 V

    Text in Illustration 
    *a
    Front view of wire harness connector
    (to Stop Light Switch Assembly)

  1. Reconnect the stop light switch assembly connector.



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR (STOP LIGHT SWITCH ASSEMBLY - IG2 RELAY)
OK


3.INSPECT STOP LIGHT SWITCH ASSEMBLY


    E145496E05
  1. Remove the stop light switch assembly (Click here).

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Switch Condition
    Specified Condition
    1 - 2
    Switch pin not pushed
    Below 0.1 Ω
    3 - 4
    Switch pin not pushed
    10 kΩ or higher
    1 - 2
    Switch pin pushed
    10 kΩ or higher
    3 - 4
    Switch pin pushed
    Below 200 Ω

    Text in Illustration 
    *a
    Component without harness connected
    (Stop Light Switch Assembly)
    *b
    Not pushed
    *c
    Pushed

  1. Reinstall the stop light switch assembly (Click here).



NG
REPLACE STOP LIGHT SWITCH ASSEMBLY (Click here)
OK


4.CHECK HARNESS AND CONNECTOR (ECM - STOP LIGHT SWITCH ASSEMBLY)
  1. Disconnect the ECM connector.

  1. Disconnect the stop light switch assembly connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance (Check for Open):
    for 2AR-FE 
    Tester Connection
    Condition
    Specified Condition
    A25-11 (STP) - A33-1
    Always
    Below 1 Ω
    A25-24 (ST1-) - A33-3
    Always
    Below 1 Ω
    for 2GR-FE 
    Tester Connection
    Condition
    Specified Condition
    A25-51 (STP) - A33-1
    Always
    Below 1 Ω
    A25-36 (ST1-) - A33-3
    Always
    Below 1 Ω


    Standard Resistance (Check for Short):
    for 2AR-FE 
    Tester Connection
    Condition
    Specified Condition
    A25-11 (STP) or A33-1 - Body ground
    Always
    10 kΩ or higher
    A25-24 (ST1-) or A33-3 - Body ground
    Always
    10 kΩ or higher
    for 2GR-FE 
    Tester Connection
    Condition
    Specified Condition
    A25-51 (STP) or A33-1 - Body ground
    Always
    10 kΩ or higher
    A25-36 (ST1-) or A33-3 - Body ground
    Always
    10 kΩ or higher

    Result:
    Result
    Proceed to
    OK (for 2AR-FE)
    A
    OK (for 2GR-FE)
    B
    NG
    C

  1. Reconnect the stop light switch assembly connector.

  1. Reconnect the ECM connector.



B
REPLACE ECM (Click here)

C
REPAIR OR REPLACE HARNESS OR CONNECTOR (ECM - STOP LIGHT SWITCH ASSEMBLY)
A

REPLACE ECM (Click here)