NAVIGATION SYSTEM > SYSTEM DESCRIPTION |
| NAVIGATION SYSTEM OUTLINE |
Vehicle position tracking methods
It is essential that the navigation system correctly tracks the current vehicle position and displays it on the map. There are 2 methods to track the current vehicle position: autonomous (dead reckoning) and GPS* (satellite) navigation. Both navigation methods are used in conjunction with each other.
*: GPS (Global Positioning System)

| Operation | Description |
| Vehicle Position Calculation | The navigation receiver assembly calculates the current vehicle position (direction and current position) using the direction deviation signal from the gyro sensor and driving distance signal from the vehicle speed sensor and creates the driving route. |
| Map Display Processing | The navigation receiver assembly processes the vehicle position data, vehicle driving track and map data from the hard disk drive. |
| Map Matching | The map data from the hard disk drive is compared to the vehicle position and driving track data. Then, the vehicle position is matched with the nearest road. |
| GPS Correction | The vehicle position is matched to the position measured by the GPS. Then, the GPS measurement position data is compared with the vehicle position and driving track data. If the position is very different, the GPS measurement position is used. |
| Distance Correction | The vehicle speed signal includes the error caused by tire wear and slippage between the tires and road surface. Distance correction is performed to account for this. The navigation receiver assembly automatically offsets the signal to make up for the difference between it and the distance data of the map. The offset is automatically updated. |

Autonomous navigation
This method determines the relative vehicle position based on the driving track determined by the gyro located in the navigation receiver assembly and the vehicle speed signal.
Gyro sensor
Used to calculate the direction by detecting angular velocity. It is located in the navigation receiver assembly.
Vehicle speed signal
Used to calculate the vehicle driving distance.
GPS* navigation (Satellite navigation)
This method detects the absolute vehicle position using radio waves from GPS satellites.
*: GPS satellites were launched by the U.S. Department of Defense for military purposes.

| Number of Satellites | Measurement | Description |
| 2 or less | Measurement is impossible | Vehicle position cannot be obtained because the number of satellites is not enough. |
| 3 | 2-dimensional measurement is possible | Vehicle position is obtained based on the current longitude and latitude. (This is less precise than 3-dimensional measurement.) |
| 4 | 3-dimensional measurement is possible | Vehicle position is obtained based on the current longitude, latitude and altitude. |
Map matching
The current driving route is calculated by autonomous navigation (according to the gyro sensor and vehicle speed signal) and GPS navigation. This information is then compared with possible road shapes from the map data in the hard disk drive and the vehicle position is set onto the most appropriate road.

Touch switch
Touch switches are touch-sensitive (interactive) switches operated by touching the screen. When a switch is pressed, the outer film bends in to contact the inner glass at the pressed position. By doing this, the voltage ratio is measured and the pressed position is detected.

| CD (Compact Disc) PLAYER OUTLINE |
A compact disc player uses a laser pickup to read digital signals recorded on a compact disc (CD). By converting the digital signals to analog, it can play music and audio.
Usable discs
This player can play only audio CDs, CD-Rs (CD-Recordable) and CD-RWs (CD-ReWritable) that have any of the following marks:

Precautions for use of discs
![]() |
Cleaning
If dirt is on the disc surface, wipe it clean with a soft dry cloth such as an eyeglass cleaner for plastic lenses from the inside to the outside in a radial direction.
| MP3/WMA OUTLINE |
Playable MP3 file standards
| Compatible standard | MP3 (MPEG1 LAYER3, MPEG2 LSF LAYER3) |
| Compatible sampling frequency |
|
| Compatible bit rate |
|
| Compatible channel mode | Stereo, joint stereo, dual channel, monaural |
Playable WMA file standards
| Compatible standard | WMA Ver. 7, 8, and 9 |
| Compatible sampling frequency | 32, 44.1, 48 (kHz) |
| Compatible bit rate (Only compatible with 2-channel playback) |
|
ID3 tag and WMA tag
Additional text information called an ID3 tag can be input to MP3 files. Information such as song titles and artist names can be stored.
Additional text information called a WMA tag can be input to WMA files. Information such as song titles and artist names can be stored.
Usable media
Only CD-ROMs, CD-Rs (CD-Recordable) and CD-RWs (CD-ReWritable) can be used to play MP3/WMA files.
Usable media format
Usable media format
| Disc format | CD-ROM Mode 1, CD-ROM XA Mode 2 Form 1 |
| File format | ISO9660 Level 1 and Level 2 (Joliet, Romeo) |
Standards and restrictions
| Maximum directory levels | 8 levels |
| Maximum number of characters for a folder name/file name | 32 characters |
| Maximum number of folders | 192 (Including empty folders, route folders, and folders that do not contain MP3/WMA files) |
| Maximum number of files in a disc | 255 (Including non-MP3/WMA files) |
File names
Only files with an extension of ".mp3" or ".wma" can be recognized and played as MP3 or WMA files.
Save MP3 or WMA files with an extension of ".mp3" or ".wma".
| "Bluetooth" OUTLINE |

| *a | Example | *b | Cellular Network |
| *c | Cellular Phone ("Bluetooth" compatible type) | *d | Navigation Receiver Assembly (Built-in "Bluetooth" receiver antenna) |
| *e | Portable Audio Player ("Bluetooth" compatible type) | *f | "Bluetooth" Wireless Connection |
"Bluetooth" is a trademark owned by Bluetooth SIG, Inc.
"Bluetooth" is a wireless connection technology that uses the 2.4 GHz frequency band.
Hands-free function
The "Bluetooth" built-in navigation receiver assembly and a "Bluetooth" compatible cellular phone*1 can be connected using a "Bluetooth" wireless connection. This enables the use of the hands-free function on the cellular phone even if the phone is in a pocket or bag. For this reason, it is not necessary to use a connector or cable to connect the cellular phone.
*1: Some versions of "Bluetooth" compatible cellular phones may not function.
Compatible hands-free devices
| Required "Bluetooth" specifications | Ver. 1.1 or higher (Ver. 2.1+EDR or higher recommended) |
| Compatible profiles |
|
| Maximum number of hands-free devices that can be registered (including audio devices) | 5 |
"Bluetooth" audio function
The "Bluetooth" built-in navigation receiver assembly and a "Bluetooth" compatible portable audio player*2 can be connected using a "Bluetooth" wireless connection. This enables files stored in the portable audio player to be heard from the vehicle speakers. In addition, operations such as play/stop can be performed directly from the navigation receiver assembly.
*2: Some versions of "Bluetooth" compatible audio players may not be able to operate the "Bluetooth" function, or music may play, but functions available using the navigation receiver assembly may be limited.
Compatible "Bluetooth" audio devices
| Required "Bluetooth" specifications | Ver. 1.1 or higher (Ver. 2.1+EDR or higher recommended) |
| Compatible profiles |
|
| Maximum number of audio devices that can be registered (including hands-free devices) | 5 |
| RADIO DESCRIPTION |
Radio frequency band
Radio broadcasts use the radio frequency bands shown in the table below.

Service area
![]() |
The service areas of AM and FM broadcasts are vastly different. Sometimes an AM broadcast can be received very clearly but an FM stereo broadcast cannot. FM stereo has the smallest service area, and is prone to pick up static and other types of interference such as noise.
| *a | FM (Stereo) |
| *b | FM (Monaural) |
| *c | AM |
Radio reception problems
![]() |
Phasing
AM broadcasts are susceptible to electrical interference and another kind of interference called phasing. Occurring only at night, phasing is the interference created when a vehicle receives 2 radio wave signals from the same transmitter. One signal is reflected off the ionosphere and the other signal is received directly from the transmitter.
| *a | Phasing |
| *b | Ionosphere |
![]() |
Multipath
Multipath is a type of interference created when a vehicle receives 2 radio wave signals from the same transmitter. One signal is reflected off buildings or mountains and the other signal is received directly from the transmitter.
| *a | Multipath |
![]() |
Fade out
Fade out is caused by objects (buildings, mountains and other such large obstacles) that deflect away part of a signal, resulting in a weaker signal when the object is between the transmitter and vehicle. High frequency radio waves, such as FM broadcasts, are easily deflected by obstructions. Low frequency radio waves, such as AM broadcasts, are less likely to deflect.
| *a | Fade Out |
Noise problem
Technicians must have a clear understanding about each customer's noise complaint. Use the following table to diagnose noise problems.
| Radio Frequency | Noise Occurrence Condition | Presumable Cause |
| AM | Noise occurs in a specific area | Foreign noise |
| Noise occurs when listening to an intermittent broadcast | An identical program transmitted from multiple towers can cause noise where the signals overlap | |
| Noise occurs only at night | Signal phasing | |
| FM | Noise occurs while driving in a specified area | Multipath resulting from a change in FM frequency |
| VEHICLE CUSTOMIZATION OUTLINE |
Customization of functions can be performed on the multi-display screen. Refer to the owner's manual for further information on customizable items for the navigation system.
| CONNECTED SERVICES OUTLINE |
The following services are available by connecting the navigation system to Toyota's portal site via the internet using a cellular phone.
| EXPORT / IMPORT MEMORY POINT FUNCTION OUTLINE |
This function allows memory points stored in the navigation receiver assembly to be registered to another navigation receiver assembly.
Memory points stored in the navigation receiver assembly can be exported to a USB device.
Data exported to a USB device can be imported to another navigation receiver assembly using a USB device.
| RDS-TMC FUNCTION OUTLINE |
This system has a function which allows the reception of traffic information from Radio Data System Traffic Message Channel (RDS-TMC) stations based on FM-multiple broadcasting.
It assists the driver to avoid areas with traffic congestion. It also helps to improve traffic flow and road safety. Traffic information can be viewed.
| USB AUDIO SYSTEM FUNCTION OUTLINE |
The No. 1 stereo jack adapter assembly is equipped with a USB terminal. Connecting a USB device or "iPod" to the No. 1 stereo jack adapter assembly allows music files to be played. Not only is it possible to play music from a USB device with audio functions, is also possible to play MP3 or WMA music files that are stored on a USB device. In addition, "iPod" control software is installed, allowing file selection from playlists and operation using shuffle mode.
USB audio system compatible model
USB device
The following device formats can be used:
| Compatible USB device formats |
|
"iPod"
"iPod" is a trademark of Apple Inc., registered in the U.S. and other countries.
| Model | Generation | Supported Firmware or OS Version |
| "iPod" | 5G | 1.3 |
| "iPod nano" | 1G | 1.3.1 |
| 2G | 1.1.3 | |
| 3G | ||
| 4G | 1.0.4 | |
| 5G | 1.0.2 | |
| 6G | 1.0 | |
| "iPod classic" | 1G | 1.1.2 |
| 2G (120GB) | 2.0.1 | |
| 2009 (160GB) | 2.0.4 | |
| "iPod touch" | 1G | iOS 3.1.3 |
| 2G | iOS 3.1.3 | |
| iOS 4.2.1 | ||
| Late 2009 (8GB) | iOS 3.1.3 | |
| iOS 4.2.1 | ||
| 3G (32GB/64GB) | iOS 3.1.3 | |
| iOS 4.2.1 | ||
| 4G | iOS 4.2.1 | |
| "iPhone" | 1G ("iPhone") | iOS 3.1.3 |
| 2G ("iPhone3G") | iOS 3.1.3 | |
| iOS 4.2.1 | ||
| 3G ("iPhone3GS") | iOS 3.1.3 | |
| iOS 4.2.1 | ||
| 4G ("iPhone4") | iOS 4.2.1 |
| Unsupported Models | "iPod shuffle" |
| "iPod" 1G, 2G, 3G, 4G | |
| "iPod mini" | |
| "iPod photo" | |
| "iPad" |
| AUTOMATIC SOUND LEVELIZER (ASL) FUNCTION OUTLINE |
The Automatic Sound Levelizer (ASL) function automatically adjusts the audio system volume level in order to compensate for increased vehicle noise (vehicle noise tends to increase as vehicle speed increases). The ASL adjusts the volume level based upon vehicle speed signals that it receives from the combination meter assembly.
| COMMUNICATION SYSTEM |
AVC-LAN Outline

Components of the navigation system communicate with each other via the AVC-LAN.
The AVC-LAN uses a twisted pair of wires for its communication lines.
The master unit of the AVC-LAN is the navigation receiver assembly.
CAN Communication Outline
The navigation system uses CAN communication between the navigation receiver assembly and ECUs.
| DIAGNOSTIC FUNCTION OUTLINE |
The navigation system has a diagnostic function (the result is indicated on the master unit).