REAR WHEEL ALIGNMENT > ADJUSTMENT |
| 1. INSPECT TIRES |
Check the tires for wear and proper inflation pressure.
| Tire Size | 4 passengers or less | 5 passengers | ||
| Front kPa (kgf/cm2, psi) | Rear kPa (kgf/cm2, psi) | Front kPa (kgf/cm2, psi) | Rear kPa (kgf/cm2, psi) | |
| 215/60R16 95V | 230 (2.3, 33) | 230 (2.3, 33)*1 240 (2.4, 35)*2 270 (2.7, 39)*3 | ||
| 215/55R17 93V | 230 (2.3, 33)*1, *2 240 (2.4, 35)*3 | 230 (2.3, 33) | 230 (2.3, 33)*1 260 (2.6, 38)*2 290 (2.9, 42)*3 | |
![]() |
Using a dial indicator, check the runout of the tires.
| 2. MEASURE VEHICLE HEIGHT |
![]() |
Bounce the vehicle up and down at the corners to stabilize the suspension.
Measure the vehicle height.
| Tire Size | Front A - B | Rear C - D |
| 215/60R16 | 112 mm (4.41 in.) 112 mm (4.41 in.)*2 110 mm (4.33 in.)*1 | 40 mm (1.57 in.) 41 mm (1.61 in.)*2 40 mm (1.57 in.)*1 |
| 215/55R17 | 116 mm (4.57 in.) 113 mm (4.45 in.)*2 117 mm (4.61 in.)*3 | 46 mm (1.81 in.) 42 mm (1.65 in.)*2 47 mm (1.85 in.)*3 |
| 3. INSPECT CAMBER |
![]() |
Install a camber-caster-kingpin gauge.
| *a | Camber-caster-kingpin Gauge |
Inspect the camber.
| Tire Size | Camber Inclination | Right-left Difference |
| 215/60R16 | -1°08' +/- 45' (-1.13° +/- 0.75°) -1°09' +/- 45' (-1.15° +/- 0.75°)*2 -1°07' +/- 45' (-1.12° +/- 0.75°)*1 | 45' (0.75°) or less |
| 215/55R17 | -1°11' +/- 45' (-1.18° +/- 0.75°) -1°09' +/- 45' (-1.15° +/- 0.75°)*2 -1°12' +/- 45' (-1.20° +/- 0.75°)*3 |
| 4. INSPECT TOE-IN |
Bounce the vehicle up and down at the corners to stabilize the suspension.
Release the parking brake and move the shift lever to N.
Push the vehicle straight ahead approximately 5 m (16.4 ft.). (Step A)
![]() |
Put tread center marks on the rearmost points of the rear wheels and measure the distance between the marks (dimension B).
| *a | Tread Center Mark |
| *b | Dimension B |
![]() | Front of the Vehicle |
Slowly push the vehicle straight ahead to cause the rear wheels to rotate 180°. Use the rear tire valve as a reference point.
![]() |
Measure the distance between the tread center marks on the front of the rear wheels (dimension A).
| *a | Dimension A |
![]() | Front of the Vehicle |
| Specified Condition |
| C + D: 0°22' +/- 0°11' (0.37° +/- 0.18°) |
| B - A: 4.0 +/- 2.0 mm (0.157 +/- 0.0787 in.) |
| 5. ADJUST TOE-IN |
![]() |
Measure the lengths of the right and left rear No. 2 suspension arms.
![]() |
Loosen the 2 lock nuts.
If the length difference between the left and right rear No. 2 suspension arm assemblies is not within the specified range, adjust it by following the procedures below.
If the toe-in measurement is greater than the specified range (too much toe-out), extend the shorter rear No. 2 suspension arm by rotating the adjusting tube so that the length difference is within the specified range.
If the toe-in measurement is less than the specified range (too much toe-in), shorten the longer rear No. 2 suspension arm by rotating the adjusting tube so that the length difference is within the specified range.
Measure the toe-in.
Turn the right and left adjusting tubes by an equal amount to adjust toe-in.
Tighten the lock nuts while securing the adjusting tube in the order indicated below: