POWER WINDOW REGULATOR MOTOR (for Front Door) > INSTALLATION |
| 1. PRECAUTION |
| 2. INSTALL FRONT POWER WINDOW REGULATOR MOTOR ASSEMBLY |
![]() |
Using a T25 "TORX" socket wrench, install the front power window regulator motor assembly with the 3 screws.
| 3. INSTALL FRONT DOOR WINDOW REGULATOR ASSEMBLY |
Apply MP grease to the sliding parts of the front door window regulator assembly.
Install the temporary bolt to the front door window regulator assembly.
![]() |
Temporarily install the front door window regulator assembly.
| *1 | Temporary Bolt |
Tighten the temporary bolt and 5 bolts to install the front door window regulator assembly.
| 4. INSTALL FRONT DOOR GLASS SUB-ASSEMBLY |
Connect the cable to the negative (-) battery terminal.
Connect the multiplex network master switch assembly and move the front door glass sub-assembly so that the door glass bolts can be seen.
Disconnect the cable from the negative (-) battery terminal.
Disconnect the multiplex network master switch assembly.
![]() |
Insert the front door glass sub-assembly into the front door panel along the front door glass run as indicated by the arrows, in the order shown in the illustration.
![]() |
Install the front door glass sub-assembly with the 2 bolts.
![]() |
Install the grommet.
| 5. INSTALL FRONT DOOR SERVICE HOLE COVER |
Apply new butyl tape to the front door panel.
![]() |
Pass the front door lock remote control cable assembly and front door inside locking cable assembly through a new front door service hole cover.
| *1 | Reference Point |
Attach the front door service hole cover according to the reference points on the front door panel.
Engage the 4 clamps.
Connect each connector.
| 6. INSTALL FRONT DOOR INNER GLASS WEATHERSTRIP |
![]() |
Install the front door inner glass weatherstrip.
| 7. INSTALL FRONT DOOR TRIM BOARD SUB-ASSEMBLY |
![]() |
Connect the front door lock remote control cable assembly and front door inside locking cable assembly.
| *1 | Front Door Inside Locking Cable Assembly |
| *2 | Front Door Lock Remote Control Cable Assembly |
Connect the connector.
![]() |
Engage the front door trim board sub-assembly with the 4 claws and reference boss as shown in the illustration.
| *1 | Reference Boss |
![]() |
Engage the 10 clips and install the front door trim board sub-assembly.
Install the 3 screws.
If protective tape has been applied, remove it.
| 8. INSTALL COURTESY LIGHT ASSEMBLY |
Connect the connector.
![]() |
Engage the claw to install the courtesy light assembly.
| *A | for LH Side |
| *B | for RH Side |
| 9. INSTALL FRONT ARMREST ASSEMBLY |
![]() |
Engage the 2 guides, 3 clips and 7 claws, and install the front armrest assembly.
| 10. INSTALL MULTIPLEX NETWORK MASTER SWITCH ASSEMBLY WITH FRONT DOOR ARMREST BASE PANEL (for Driver Side) |
Connect each connector.
![]() |
Engage the 4 guides, 2 clips and 5 claws, and install the multiplex network master switch assembly with front door armrest base panel.
| 11. INSTALL POWER WINDOW REGULATOR SWITCH ASSEMBLY WITH FRONT DOOR ARMREST BASE PANEL (for Front Passenger Side) |
Connect the connector.
![]() |
Engage the 4 guides, 2 clips and 5 claws, and install the power window regulator switch assembly with front door armrest base panel.
| 12. INSTALL FRONT DOOR LOWER FRAME BRACKET GARNISH |
![]() |
Engage the 3 clips to install the front door lower frame bracket garnish.
| 13. INSTALL FRONT DOOR INSIDE HANDLE BEZEL PLUG |
![]() |
Engage the 3 claws to install the front door inside handle bezel plug.
| 14. CONNECT CABLE TO NEGATIVE BATTERY TERMINAL |
| 15. INITIALIZE POWER WINDOW CONTROL SYSTEM |
| 16. INSPECT POWER WINDOW OPERATION |