DTC B2412 Headlight Swivel Motor LH Malfunction |
DTC B2413 Headlight Swivel Motor RH Malfunction |
| DTC No. | DTC Detection Condition | Trouble Area |
| B2412 |
|
|
| B2413 |
|
|

| 1.CHECK FOR DTC |
Clear the DTCs (Click here).
Check for DTCs (Click here).
|
| ||||
| OK | ||
| ||
| 2.PERFORM ACTIVE TEST USING INTELLIGENT TESTER |
Connect the intelligent tester to the DLC3.
Start the engine.
Turn the intelligent tester on.
Enter the following menus: Body / AFS / Active Test.
Check that the swivel motors operate.
| Tester Display | Test Part | Control Range | Diagnostic Note |
| Drive Swivel Motor LH LEFT | Swivel motor LH left direction rotation | ON/OFF | ON: Moves left OFF: Stops |
| Drive Swivel Motor LH RIGHT | Swivel motor LH right direction rotation | ON/OFF | ON: Moves right OFF: Stops |
| Drive Swivel Motor RH LEFT | Swivel motor RH left direction rotation | ON/OFF | ON: Moves left OFF: Stops |
| Drive Swivel Motor RH RIGHT | Swivel motor RH right direction rotation | ON/OFF | ON: Moves right OFF: Stops |
|
| ||||
| OK | |
| 3.CHECK HEADLIGHT UNIT (HEADLIGHT SWIVEL MOTOR) |
Replace the headlight unit with a new or a known good one (Click here).
Check for DTCs (Click here).
|
| ||||
| OK | ||
| ||
| 4.CHECK HARNESS AND CONNECTOR (BATTERY - AFS ECU (HEADLIGHT SWIVEL ECU ASSEMBLY)) |
![]() |
Disconnect the A35 AFS ECU (headlight swivel ECU assembly) connector.
Measure the voltage according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
| A35-14 (IGS) - Body ground | Ignition switch ON | 11 to 14 V |
| *a | Front view of wire harness connector (to AFS ECU (Headlight Swivel ECU Assembly)) |
|
| ||||
| OK | |
| 5.CHECK HARNESS AND CONNECTOR (AFS ECU (HEADLIGHT SWIVEL ECU ASSEMBLY) - BODY GROUND) |
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
| A35-22 (E1) - Body ground | Always | Below 1 Ω |
|
| ||||
| OK | |
| 6.CHECK HARNESS AND CONNECTOR (AFS ECU (HEADLIGHT SWIVEL ECU ASSEMBLY) - HEADLIGHT UNIT) |
Disconnect the LH side or RH side headlight unit connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
| A35-1 (SMBL) - A22-1 (SMBL) | Always | Below 1 Ω |
| A35-29 (SML) - A22-2 (SML) | Always | Below 1 Ω |
| A35-23 (SMGL) - A22-3 (SMGL) | Always | Below 1 Ω |
| A35-1 (SMBL) - Body ground | Always | 10 kΩ or higher |
| A35-29 (SML) - Body ground | Always | 10 kΩ or higher |
| A35-23 (SMGL) - Body ground | Always | 10 kΩ or higher |
| Tester Connection | Condition | Specified Condition |
| A35-2 (SMBR) - A67-1 (SMBR) | Always | Below 1 Ω |
| A35-10 (SMR) - A67-2 (SMR) | Always | Below 1 Ω |
| A35-24 (SMGR) - A67-3 (SMGR) | Always | Below 1 Ω |
| A35-2 (SMBR) - Body ground | Always | 10 kΩ or higher |
| A35-10 (SMR) - Body ground | Always | 10 kΩ or higher |
| A35-24 (SMGR) - Body ground | Always | 10 kΩ or higher |
|
| ||||
| OK | |
| 7.INSPECT AFS ECU (HEADLIGHT SWIVEL ECU ASSEMBLY) |
![]() |
Reconnect the A35 AFS ECU (headlight swivel ECU assembly) connector.
Measure the voltage according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
| A35-1 (SMBL) - A35-23 (SMGL) | Ignition switch off | Below 1 V |
| Ignition switch ON | 11 to 14 V |
| Tester Connection | Condition | Specified Condition |
| A35-2 (SMBR) - A35-24 (SMGR) | Ignition switch off | Below 1 V |
| Ignition switch ON | 11 to 14 V |
| *a | Component with harness connected (AFS ECU (Headlight Swivel ECU Assembly)) |
|
| ||||
| OK | |
| 8.CHECK HEADLIGHT UNIT (HEADLIGHT SWIVEL MOTOR) |
Replace the headlight unit with a new or a known good one (Click here).
Check for DTCs (Click here).
|
| ||||
| OK | ||
| ||