Home › Audio / Visual / Telematics › AUDIO / VIDEO › AUDIO AND VISUAL SYSTEM (for Radio Receiver Type)

AUDIO AND VISUAL SYSTEM (for Radio Receiver Type) > Illumination Circuit

for Preparation Click here


DESCRIPTION

Power is supplied to the radio receiver assembly and steering pad switch illumination when the light control switch is in the tail or head position.

WIRING DIAGRAM


E232803E05


INSPECTION PROCEDURE

NOTICE:
  1. The vehicle is equipped with a Supplemental Restraint System (SRS) which includes components such as airbags. Before servicing (including removal or installation of parts), be sure to read the precaution for Supplemental Restraint System (Click here).
  2. Inspect the fuse for circuits related to this system before performing the following inspection procedure.

1.CHECK ILLUMINATION
  1. Check if the illumination for the radio receiver assembly, steering pad switch, heater control switch or others (hazard switch, transmission control switch, etc.) comes on when the light control switch is turned to the head or tail position.

    Result:

    Result
    Proceed to
    Illumination comes on for all components except steering pad switch.
    A
    Illumination comes on for all components except radio receiver assembly.
    B
    No illumination comes on (radio receiver assembly, hazard switch, heater control switch, etc.).
    C



B
Go to step 5

C
GO TO LIGHTING SYSTEM (Click here)
A


2.CHECK HARNESS AND CONNECTOR (ILLUMINATION SIGNAL)
  1. Disconnect the spiral cable sub-assembly connector.

  1. Measure the voltage according to the value(s) in the table below.

    Standard Voltage:
    Tester Connection
    Condition
    Specified Condition
    I28-13 (IL+2) - Body ground
    Light control switch in the tail or head position
    11 to 14 V



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK


3.INSPECT STEERING PAD SWITCH
  1. Disconnect the steering pad switch connector.



  1. Connect a battery positive (+) lead to terminal IL+2 and a negative (-) lead to terminal -DP of the steering pad switch connector.


    E224425E01


    E224427E01

  1. Check if the illumination for the steering pad switch comes on.

    OK:
    Illumination for the steering pad switch comes on.


Text in Illustration 
*A
w/ Microphone
*B
w/o Microphone
*a
Component without harness connected
(Steering Pad Switch)
-
-


NG
REPLACE STEERING PAD SWITCH (Click here)
OK


4.INSPECT SPIRAL CABLE SUB-ASSEMBLY
  1. Disconnect the steering pad switch and spiral cable sub-assembly connectors.



    E226306E09
  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    z3-5 (IL+2) - I28-13 (IL+2)
    Center
    Below 1 Ω
    2.5 rotations to the left
    2.5 rotations to the right
    z3-3 (-DP) - I28-11 (-DP)
    Center
    Below 1 Ω
    2.5 rotations to the left
    2.5 rotations to the right

  1. After setting the spiral cable sub-assembly to the center position, rotate the spiral cable sub-assembly 2.5 times clockwise. Then while rotating the spiral cable sub-assembly 5 times counterclockwise, measure the resistance as shown in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    z3-5 (IL+2) - I28-13 (IL+2)
    Always
    Below 3 Ω
    z3-3 (-DP) - I28-11 (-DP)
    Always
    Below 3 Ω

    NOTICE:
    1. Press and hold the lock located in the center of the spiral cable sub-assembly to rotate the spiral cable sub-assembly.
    2. The spiral cable sub-assembly is an important part of the SRS airbag system. Incorrect removal or installation of the spiral cable sub-assembly may prevent the airbag from deploying. Refer to the pages shown in the brackets.
    3. As the spiral cable sub-assembly may break, do not rotate the spiral cable sub-assembly more than the specified amount.

    HINT:
    1. Removal (Click here)
    2. Installation (Click here)

    Text in Illustration 
    *a
    Component without harness connected
    (Spiral cable sub-assembly)
    *b
    Steering Pad Switch Side
    *c
    Vehicle Side



NG
REPLACE SPIRAL CABLE SUB-ASSEMBLY (Click here)
OK

REPAIR OR REPLACE HARNESS AND CONNECTOR (SPIRAL CABLE SUB-ASSEMBLY - BODY GROUND) 

5.CHECK HARNESS AND CONNECTOR (ILLUMINATION SIGNAL)
  1. Disconnect the radio receiver assembly connector.

  1. Measure the voltage according to the value(s) in the table below.

    Standard Voltage:
    Tester Connection
    Condition
    Specified Condition
    I148-10 (ILL+) - Body ground
    Light control switch in the tail or head position
    11 to 14 V



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK

PROCEED TO NEXT SUSPECTED AREA SHOWN IN PROBLEM SYMPTOMS TABLE (Click here)