AUDIO AND VISUAL SYSTEM (for Radio Receiver Type) > Steering Pad Switch Circuit |


| 1.CHECK HARNESS AND CONNECTOR (STEERING PAD SWITCH SIGNAL) |
Disconnect the radio receiver assembly connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
| I150-21 (SW1) - I150-23 (SWG) | No switch pushed | 95 to 105 kΩ |
| Seek+ switch pushed | Below 2.5 Ω | |
| Seek- switch pushed | 313 to 345 Ω | |
| Volume+ switch pushed | 950 to 1050 Ω | |
| Volume- switch pushed | 2955 to 3265 Ω | |
| I150-22 (SW2) - I150-23 (SWG) | No switch pushed | 95 to 105 kΩ |
| MODE/HOLD switch pushed | Below 2.5 Ω | |
| On hook switch pushed*1 | 313 to 345 Ω | |
| Off hook switch pushed*1 | 950 to 1050 Ω |
|
| ||||
| OK | ||
| ||
| 2.INSPECT STEERING PAD SWITCH |
Disconnect the steering pad switch connector.
Measure the resistance according to the value(s) in the table below.


| Tester Connection | Condition | Specified Condition |
| z3-11 (AU1) - z3-8 (EAU) | No switch pushed | 95 to 105 kΩ |
| Seek+ switch pushed | Below 2.5 Ω | |
| Seek- switch pushed | 313 to 345 Ω | |
| Volume+ switch pushed | 950 to 1050 Ω | |
| Volume- switch pushed | 2955 to 3265 Ω | |
| z3-10 (AU2) - z3-8 (EAU) | No switch pushed | 95 to 105 kΩ |
| MODE/HOLD switch pushed | Below 2.5 Ω | |
| On hook switch pushed*1 | 313 to 345 Ω | |
| Off hook switch pushed*1 | 950 to 1050 Ω |
| *A | w/ Microphone | *B | w/o Microphone |
| *a | Component without harness connected (Steering Pad Switch) | *b | Volume+ |
| *c | Volume- | *d | Seek- |
| *e | Seek+ | *f | MODE/HOLD |
| *g | Off hook | *h | On hook |
|
| ||||
| OK | |
| 3.INSPECT SPIRAL CABLE SUB-ASSEMBLY |
Disconnect the steering pad switch and spiral cable sub-assembly connectors.
![]() |
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
| z3-8 (EAU) - I28-3 (EAU) | Center | Below 1 Ω |
| 2.5 rotations to the left | ||
| 2.5 rotations to the right | ||
| z3-11 (AU1) - I28-6 (AU1) | Center | Below 1 Ω |
| 2.5 rotations to the left | ||
| 2.5 rotations to the right | ||
| z3-10 (AU2) - I28-5 (AU2) | Center | Below 1 Ω |
| 2.5 rotations to the left | ||
| 2.5 rotations to the right |
After setting the spiral cable sub-assembly to the center position, rotate the spiral cable sub-assembly 2.5 times clockwise. Then while rotating the spiral cable sub-assembly 5 times counterclockwise, measure the resistance as shown in the table below.
| Tester Connection | Condition | Specified Condition |
| z3-8 (EAU) - I28-3 (EAU) | Always | Below 3 Ω |
| z3-11 (AU1) - I28-6 (AU1) | Always | Below 3 Ω |
| z3-10 (AU2) - I28-5 (AU2) | Always | Below 3 Ω |
| *a | Component without harness connected (Spiral cable sub-assembly) |
| *b | Steering Pad Switch Side |
| *c | Vehicle Side |
|
| ||||
| OK | ||
| ||