Home › Audio / Visual / Telematics › AUDIO / VIDEO › AUDIO AND VISUAL SYSTEM (for Radio Receiver Type)

AUDIO AND VISUAL SYSTEM (for Radio Receiver Type) > Steering Pad Switch Circuit

for Preparation Click here


DESCRIPTION

This circuit sends an operation signal from the steering pad switch to the radio receiver assembly.
If there is an open in the circuit, the audio system cannot be operated using the steering pad switch.
If there is a short in the circuit, the same condition as when a switch is continuously depressed occurs.
Therefore, the radio receiver assembly cannot be operated using the steering pad switch, and also the radio receiver assembly itself cannot function.

WIRING DIAGRAM


E224428E01


E224429E01


INSPECTION PROCEDURE

NOTICE:
The vehicle is equipped with a Supplemental Restraint System (SRS) which includes components such as airbags. Before servicing (including removal or installation of parts), be sure to read the precaution for Supplemental Restraint System (Click here).

1.CHECK HARNESS AND CONNECTOR (STEERING PAD SWITCH SIGNAL)
  1. Disconnect the radio receiver assembly connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    I150-21 (SW1) - I150-23 (SWG)
    No switch pushed
    95 to 105 kΩ
    Seek+ switch pushed
    Below 2.5 Ω
    Seek- switch pushed
    313 to 345 Ω
    Volume+ switch pushed
    950 to 1050 Ω
    Volume- switch pushed
    2955 to 3265 Ω
    I150-22 (SW2) - I150-23 (SWG)
    No switch pushed
    95 to 105 kΩ
    MODE/HOLD switch pushed
    Below 2.5 Ω
    On hook switch pushed*1
    313 to 345 Ω
    Off hook switch pushed*1
    950 to 1050 Ω

    *1: w/ Microphone



NG
Go to step 2
OK

PROCEED TO NEXT SUSPECTED AREA SHOWN IN PROBLEM SYMPTOMS TABLE (Click here)  

2.INSPECT STEERING PAD SWITCH
  1. Disconnect the steering pad switch connector.



  1. Measure the resistance according to the value(s) in the table below.


    E224424E01


    E224426E01


    Standard Resistance:

    Tester Connection
    Condition
    Specified Condition
    z3-11 (AU1) - z3-8 (EAU)
    No switch pushed
    95 to 105 kΩ
    Seek+ switch pushed
    Below 2.5 Ω
    Seek- switch pushed
    313 to 345 Ω
    Volume+ switch pushed
    950 to 1050 Ω
    Volume- switch pushed
    2955 to 3265 Ω
    z3-10 (AU2) - z3-8 (EAU)
    No switch pushed
    95 to 105 kΩ
    MODE/HOLD switch pushed
    Below 2.5 Ω
    On hook switch pushed*1
    313 to 345 Ω
    Off hook switch pushed*1
    950 to 1050 Ω

    *1: w/ Microphone

    Text in Illustration 
    *A
    w/ Microphone
    *B
    w/o Microphone
    *a
    Component without harness connected
    (Steering Pad Switch)
    *b
    Volume+
    *c
    Volume-
    *d
    Seek-
    *e
    Seek+
    *f
    MODE/HOLD
    *g
    Off hook
    *h
    On hook



NG
REPLACE STEERING PAD SWITCH (Click here)
OK


3.INSPECT SPIRAL CABLE SUB-ASSEMBLY
  1. Disconnect the steering pad switch and spiral cable sub-assembly connectors.



    E226306E08
  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    z3-8 (EAU) - I28-3 (EAU)
    Center
    Below 1 Ω
    2.5 rotations to the left
    2.5 rotations to the right
    z3-11 (AU1) - I28-6 (AU1)
    Center
    Below 1 Ω
    2.5 rotations to the left
    2.5 rotations to the right
    z3-10 (AU2) - I28-5 (AU2)
    Center
    Below 1 Ω
    2.5 rotations to the left
    2.5 rotations to the right

  1. After setting the spiral cable sub-assembly to the center position, rotate the spiral cable sub-assembly 2.5 times clockwise. Then while rotating the spiral cable sub-assembly 5 times counterclockwise, measure the resistance as shown in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    z3-8 (EAU) - I28-3 (EAU)
    Always
    Below 3 Ω
    z3-11 (AU1) - I28-6 (AU1)
    Always
    Below 3 Ω
    z3-10 (AU2) - I28-5 (AU2)
    Always
    Below 3 Ω

    NOTICE:
    1. Press and hold the lock located in the center of the spiral cable sub-assembly to rotate the spiral cable sub-assembly.
    2. The spiral cable sub-assembly is an important part of the SRS airbag system. Incorrect removal or installation of the spiral cable sub-assembly may prevent the airbag from deploying. Refer to the pages shown in the brackets.
    3. As the spiral cable sub-assembly may break, do not rotate the spiral cable sub-assembly more than the specified amount.

    HINT:
    1. Removal (Click here)
    2. Installation (Click here)

    Text in Illustration 
    *a
    Component without harness connected
    (Spiral cable sub-assembly)
    *b
    Steering Pad Switch Side
    *c
    Vehicle Side



NG
REPLACE SPIRAL CABLE SUB-ASSEMBLY (Click here)
OK

REPAIR OR REPLACE HARNESS OR CONNECTOR (RADIO RECEIVER ASSEMBLY - SPIRAL CABLE SUB-ASSEMBLY)