Home › Audio / Visual / Telematics › AUDIO / VIDEO › AUDIO AND VISUAL SYSTEM (for Radio and Display Type)

AUDIO AND VISUAL SYSTEM (for Radio and Display Type) > Steering Pad Switch Circuit

for Preparation Click here


DESCRIPTION

This circuit sends an operation signal from the steering pad switch assembly to the radio and display receiver assembly.
If there is an open in the circuit, the audio system cannot be operated using the steering pad switch assembly.
If there is a short in the circuit, the same condition as when a switch is continuously depressed occurs.
Therefore, the radio and display receiver assembly cannot be operated using the steering pad switch assembly, and also the radio and display receiver assembly itself cannot function.

WIRING DIAGRAM


E229628E05


INSPECTION PROCEDURE

NOTICE:
The vehicle is equipped with a Supplemental Restraint System (SRS) which includes components such as airbags. Before servicing (including removal or installation of parts), be sure to read the precaution for Supplemental Restraint System (Click here).

1.CHECK HARNESS AND CONNECTOR (STEERING PAD SWITCH SIGNAL)
  1. Disconnect the radio and display receiver assembly connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    I155-21 (SW1) - I155-23 (SWG)
    No switch pushed
    95 to 105 kΩ
    Up switch pushed
    Below 2.5 Ω
    Down switch pushed
    313 to 345 Ω
    Volume+ switch pushed
    950 to 1050 Ω
    Volume- switch pushed
    2955 to 3265 Ω
    I155-22 (SW2) - I155-23 (SWG)
    No switch pushed
    95 to 105 kΩ
    MODE/HOLD switch pushed
    Below 2.5 Ω
    On hook switch pushed
    313 to 345 Ω
    Off hook switch pushed
    950 to 1050 Ω
    I155-24 (SW3) - I155-23 (SWG)
    No switch pushed
    95 to 105 kΩ
    Enter switch pushed
    Below 2.5 Ω
    Back switch pushed
    313 to 345 Ω
    Right switch pushed
    950 to 1050 Ω
    Left switch pushed
    2955 to 3265 Ω



NG
Go to step 2
OK

PROCEED TO NEXT SUSPECTED AREA SHOWN IN PROBLEM SYMPTOMS TABLE (Click here)  

2.INSPECT STEERING PAD SWITCH ASSEMBLY


  1. Disconnect the steering pad switch assembly connector.


    E229629E03

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    z3-11 (AU1) - z3-8 (EAU)
    No switch pushed
    95 to 105 kΩ
    Up switch pushed
    Below 2.5 Ω
    Down switch pushed
    313 to 345 Ω
    Volume+ switch pushed
    950 to 1050 Ω
    Volume- switch pushed
    2955 to 3265 Ω
    z3-10 (AU2) - z3-8 (EAU)
    No switch pushed
    95 to 105 kΩ
    MODE/HOLD switch pushed
    Below 2.5 Ω
    On hook switch pushed
    313 to 345 Ω
    Off hook switch pushed
    950 to 1050 Ω
    z3-9 (AU3) - z3-8 (EAU)
    No switch pushed
    95 to 105 kΩ
    Enter switch pushed
    Below 2.5 Ω
    Back switch pushed
    313 to 345 Ω
    Right switch pushed
    950 to 1050 Ω
    Left switch pushed
    2955 to 3265 Ω


    Text in Illustration 
    *A
    w/ DISP Switch of Steering Pad Switch Assembly
    -
    -
    *a
    Component without harness connected
    (Steering Pad Switch Assembly)
    *b
    Volume+
    *c
    Volume-
    *d
    Back
    *e
    MODE/HOLD
    *f
    Up
    *g
    Down
    *h
    Left
    *i
    Right
    *j
    Enter
    *k
    Off hook
    *l
    On hook
    *m
    DISP
    -
    -



NG
REPLACE STEERING PAD SWITCH ASSEMBLY (Click here)
OK


3.INSPECT SPIRAL CABLE SUB-ASSEMBLY
  1. Disconnect the steering pad switch assembly connector.

  1. Disconnect the spiral cable sub-assembly connector.



    E226306E11
  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    z3-8 (EAU) - I28-3 (EAU)
    Center
    Below 1 Ω
    2.5 rotations to the left
    2.5 rotations to the right
    z3-11 (AU1) - I28-6 (AU1)
    Center
    Below 1 Ω
    2.5 rotations to the left
    2.5 rotations to the right
    z3-10 (AU2) - I28-5 (AU2)
    Center
    Below 1 Ω
    2.5 rotations to the left
    2.5 rotations to the right
    z3-9 (AU3) - I28-4 (AU3)
    Center
    Below 1 Ω
    2.5 rotations to the left
    2.5 rotations to the right

  1. After setting the spiral cable sub-assembly to the center position, rotate the spiral cable sub-assembly 2.5 times clockwise. Then while rotating the spiral cable sub-assembly 5 times counterclockwise, measure the resistance as shown in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    z3-8 (EAU) - I28-3 (EAU)
    Always
    Below 3 Ω
    z3-11 (AU1) - I28-6 (AU1)
    Always
    Below 3 Ω
    z3-10 (AU2) - I28-5 (AU2)
    Always
    Below 3 Ω
    z3-9 (AU3) - I28-4 (AU3)
    Always
    Below 3 Ω

    NOTICE:
    1. Press and hold the lock located in the center of the spiral cable sub-assembly to rotate the spiral cable sub-assembly.
    2. The spiral cable sub-assembly is an important part of the SRS airbag system. Incorrect removal or installation of the spiral cable sub-assembly may prevent the airbag from deploying. Refer to the pages shown in the brackets.
    3. As the spiral cable sub-assembly may break, do not rotate the spiral cable sub-assembly more than the specified amount.

    HINT:
    1. Removal (Click here)
    2. Installation (Click here)

    Text in Illustration 
    *a
    Component without harness connected
    (Spiral Cable Sub-assembly)
    *b
    Steering Pad Switch Assembly Side
    *c
    Vehicle Side



NG
REPLACE SPIRAL CABLE SUB-ASSEMBLY (Click here)
OK

REPAIR OR REPLACE HARNESS OR CONNECTOR (RADIO AND DISPLAY RECEIVER ASSEMBLY - SPIRAL CABLE SUB-ASSEMBLY)