Home › Vehicle Interior › METER / GAUGE / DISPLAY › METER / GAUGE SYSTEM

METER / GAUGE SYSTEM > DATA LIST / ACTIVE TEST

for Preparation Click here



DATA LIST
Using the intelligent tester to read the Data List allows the values or states of switches, sensors, actuators and other items to be read without removing any parts. This non-intrusive inspection can be very useful because intermittent conditions or signals may be discovered before parts or wiring is disturbed. Reading the Data List information early in troubleshooting is one way to save diagnostic time.

NOTICE:
In the table below, the values listed under "Normal Condition" are reference values. Do not depend solely on these reference values when deciding whether a part is faulty or not.

  1. Warm up the engine.

  2. Turn the ignition switch off.

  3. Connect the intelligent tester to the DLC3.

  4. Turn the ignition switch to ON.

  5. Turn the intelligent tester on.

  6. Enter the following menus:

    1. for Combination Meter: Body / Combination Meter / Data List.

    2. for ABS/VSC/TRC: Chassis / ABS/VSC/TRC / Data List.

    3. for Engine and ECT: Powertrain / Engine and ECT / Data List.

    4. for Main Body: Body / Main Body / Data List.

  7. Check the values by referring to the table below.

    Combination Meter 
    Tester Display
    Measurement Item/Range
    Normal Condition
    Diagnostic Note
    ODO/TRIP Change SW
    ODO/TRIP change switch/OFF or ON
    OFF: Switch released
    -
    ON: Switch pushed
    -
    P-Seatbelt Buckle SW
    Front passenger seat belt buckle switch/OFF or ON
    OFF: Front passenger seat belt fastened (warning light off)
    -
    ON: Front passenger seat belt unfastened (warning light on)
    Vehicle Speed Meter
    Vehicle speed/Min.: 0 km/h (0 mph), Max.: 255 km/h (158 mph)
    Almost the same as actual vehicle speed
    -
    Engine Rpm
    Engine speed/Min.: 0 rpm, Max.: 12750 rpm
    1. 600 to 700 rpm: Idling (for 2GR-FE)
    2. 610 to 710 rpm: Idling (for 2AR-FE, 1AZ-FE)
    -
    Coolant Temperature
    Engine coolant temperature/-40 to 127.5°C (-40 to 261.5°F)
    After warming up: 75 to 100°C (167 to 212°F)

    HINT:
    1. After warming up the engine, the engine coolant temperature is 75 to 100°C (167 to 212°F).
    2. After a long soak, the engine coolant temperature, intake air temperature and ambient air temperature are approximately equal.
    3. If the value is -40°C (-40°F), or higher than 135°C (275°F), the sensor circuit is open or shorted.
    4. Check if the engine overheats when the value indicates higher than 135°C (275°F).

    Washer Switch
    Washer fluid level warning switch/OFF or ON
    OFF: Washer fluid level not low
    -
    ON: Washer fluid level low
    -
    Fuel Input
    Fuel input/Min.: 0, Max. 127.5
    Fuel receiver gauge indicates F: 57.0
    Unit: Liter
    Fuel receiver gauge indicates 3/4: 48.3
    Fuel receiver gauge indicates 1/2: 32.2
    Fuel receiver gauge indicates 1/4: 16.1
    Fuel receiver gauge indicates E: 6.4
    Multi Display Select Switch*1
    DISP switch in the steering pad switch assembly/OFF or ON
    OFF: DISP switch in the steering pad switch assembly not pressed
    -
    ON: DISP switch in the steering pad switch assembly pressed
    +B Voltage Value
    Battery voltage/Min.: 0 V, Max.: 25.5 V
    11 to 14 V
    -
    Integrated Value for Oil Maintenance*2
    Maintenance required reminder light value/Min.: 0, Max.: 25500 (mile)
    Driving distance after performing maintenance required reminder resetting procedure displayed
    If the value is 5000 (miles) or more, perform the maintenance required reminder resetting procedure after performing maintenance.
    Ambient Temperature
    Outside temperature/Min.: -40°C (-40°F), Max.: 87.5°C (189.5°F)
    Almost the same as actual outside temperature
    The temperature displayed on the multi-information display is -40 to 50°C (-40 to 122°F)
    Oil Pressure Switch
    Oil pressure switch/OFF or ON
    OFF: Engine starts
    -
    ON: Engine does not start
    Turn Signal Switch (Left)
    LH turn signal switch/OFF or ON
    OFF: LH turn switch off
    -
    ON: LH turn switch on
    Turn Signal Switch (Right)
    RH turn signal switch/OFF or ON
    OFF: RH turn switch off
    -
    ON: RH turn switch on
    Hazard Flasher Switch
    Hazard warning switch/OFF or ON
    OFF: Switch released
    -
    ON: Switch pushed
    TRC OFF SW*2
    VSC OFF switch/OFF or ON
    OFF: Switch released
    -
    ON: Switch pushed
    Key Remind Sound
    Cycle of the key reminder warning buzzer
    The cycle of the key reminder warning buzzer/Large, Medium, Small
    -
    Key Remind Volume
    Volume of the key reminder warning buzzer
    The volume of the key reminder warning buzzer/Fast, Normal, Slow
    -
    Driver seatbelt Warning Buzzer
    Condition of the seat belt warning buzzer/OFF or ON
    OFF: The seat belt warning buzzer does not sound at vehicle speed of 20 km/h (12 mph) or more when the driver seat belt unfastened
    Displays customize setting of seat belt warning buzzer
    ON: The seat belt warning buzzer sounds at vehicle speed of 20 km/h (12 mph) or more when the driver seat belt unfastened
    P-Seatbelt Warning Buzzer
    Condition of the seat belt warning buzzer/OFF or ON
    OFF: The seat belt warning buzzer does not sound at vehicle speed of 20 km/h (12 mph) or more when the front passenger seat belt unfastened
    Displays customize setting of seat belt warning buzzer
    ON: The seat belt warning buzzer sounds at vehicle speed of 20 km/h (12 mph) or more when the front passenger seat belt unfastened
    Number of Trouble Code
    The number of DTC currently stored
    0 to 255
    -

    1. *1: w/ DISP Switch
    2. *2: Although the item is displayed on the intelligent tester, no data can be operated.

    ABS/VSC/TRC 
    Tester Display
    Measurement Item/Range
    Normal Condition
    Diagnostic Note
    Vehicle Speed
    Vehicle speed/Min.: 0 km/h (0 mph), Max.: 326 km/h (202 mph)
    Vehicle stopped: 0 km/h (0 mph)
    When driving at constant speed: No large fluctuations

    Engine and ECT 
    Tester Display
    Measurement Item/Range
    Normal Condition
    Diagnostic Note
    Injection Volum (Cylinder 1)
    Injection volume (cylinder 1)/Min.: 0 ml, Max.: 2.047 ml
    0 to 0.5 ml
    1. Stored as Freeze Frame Data
    2. This is the fuel injection volume for 10 injections.
    Results of real-vehicle check (for 2AR-FE):
    1. Idling (engine warmed up): 0.108 ml
    2. Running without load (3000 rpm): 0.097 ml
    Results of real-vehicle check (for 2GR-FE):
    1. Idling (engine warmed up): 0.083 ml
    2. Running without load (3000 rpm): 0.093 ml
    3. Vehicle driven at constant speed of 60 km/h (37 mph): 0.197 ml
    Results of real-vehicle check (for 1AZ-FE):
    1. Idling (engine warmed up): 0.087 ml
    2. Running without load (3000 rpm): 0.089 ml
    Engine Speed
    Engine speed/Min.: 0 rpm, Max.: 16383 rpm
    1. 600 to 700 rpm: Idling (for 2GR-FE)
    2. 610 to 710 rpm: Idling (for 2AR-FE, 1AZ-FE)
    1. Stored as Freeze Frame Data
    2. When the crankshaft position sensor is malfunctioning, "Engine Speed" is approximately 0 rpm or varies greatly from the actual engine speed.
    Results of real-vehicle check:
    Idling (engine warmed up and A/C off): 660 rpm
    Coolant Temp
    Coolant temperature/Min.: -40°C (-40°F), Max.: 140°C (284°F)
    75 to 100°C (167 to 212°F): After warming up
    1. Stored as Freeze Frame Data
    2. This is the engine coolant temperature.

    HINT:
    1. After warming up the engine, the engine coolant temperature is 75 to 100°C (167 to 212°F).
    2. After a long soak, the engine coolant temperature, intake air temperature and ambient air temperature are approximately equal.
    3. If the value is -40°C (-40°F), or 140°C (284°F), the sensor circuit is open or shorted.
    4. Check if the engine overheats when the value indicates 140°C (284°F).


    Main Body 
    Tester Display
    Measurement Item/Range
    Normal Condition
    Diagnostic Note
    Illumination Rate Info
    Illumination rate information/0 ms to 2162.65 ms
    Value output according to ambient light level
    -


ACTIVE TEST
Using the intelligent tester to perform Active Tests allows relays, VSVs, actuators and other items to be operated without removing any parts. This non-intrusive functional inspection can be very useful because intermittent operation may be discovered before parts or wiring is disturbed. Performing Active Tests early in troubleshooting is one way to save diagnostic time. Data List information can be displayed while performing Active Tests.
  1. Connect the intelligent tester to the DLC3.

  2. Turn the ignition switch to ON.

  3. Turn the intelligent tester on.

  4. Enter the following menus: Body / Combination Meter / Active Test.

  5. Check the operation by referring to the table below.

    Combination Meter 
    Tester Display
    Test Part
    Control Range
    Diagnostic Note
    Speed Meter Operation
    Speedometer
    OFF, 0, 40, 80, 120, 160, 200, 240 km/h
    -
    Tacho Meter Operation
    Tachometer
    OFF, 1000, 2000, 3000, 4000, 5000, 6000, 7000 (rpm)
    -
    Fuel Meter Operation
    Fuel receiver gauge
    OFF, Empty, 1/2, Full
    -
    Fuel Consumption Meter Operation
    Fuel consumption meter
    OFF, MIN, 1/4, 1/2, 3/4, MAX
    -
    A/T Indicator Operation 1
    Shift indicator light
    OFF, L, 2, 3(M), 4(M), D, N, R, P
    -
    A/T Indicator Operation 2
    Shift indicator light
    OFF, 8, 5, 6, 7, Es, B
    -
    A/T Indicator Operation 3
    Shift indicator light
    OFF, D
    -
    Indicat. Lamp Airbag
    SRS warning light
    OFF or ON
    -
    Indicat. Lamp Doors All Open
    Door indicator light
    OFF or ON
    -
    Driver Side Seat Belt
    Seat belt warning light
    OFF or ON
    -
    Indicat. Lamp ABS
    ABS warning light
    OFF or ON
    -
    Indicat. Lamp Charge
    Charge warning light
    OFF or ON
    -
    Indicat. Lamp Slip
    Slip indicator light
    OFF or ON
    -
    Indicat. Lamp Beam
    High beam indicator light
    OFF or ON
    -
    Indicat. Lamp Head
    Head indicator light
    OFF or ON
    *6
    Indicat. Lamp Tail
    Tail indicator light
    OFF or ON
    -
    Indicat. Lamp Fr FOG
    Front fog indicator light
    OFF or ON
    -
    Indicat. Lamp Rr FOG*1
    Rear fog indicator light
    OFF or ON
    -
    Indicat. Lamp Washer
    Washer fluid level warning light
    OFF or ON
    -
    Indicat. AFS*2
    AFS warning light
    OFF or ON
    -
    Indicat. Lamp Fuel
    Fuel level warning light
    OFF or ON
    -
    VSC TRC Indicator
    TRC OFF indicator light
    OFF or ON
    -
    Indicat. Tire Pressure Warning System*3
    Tire pressure warning light
    OFF or ON
    *6
    Indicat. Oil Pressure
    Oil pressure warning light
    OFF or ON
    -
    Indicat. ECONO
    ECO indicator light
    OFF or ON
    -
    Indicat. Lamp Cruise*9
    Cruise control indicator light (green)
    OFF or ON
    -
    Indicat. Lamp Brake
    Brake warning light
    OFF or ON
    -
    Indicat. EPS
    EPS warning light
    OFF or ON
    -
    Maintenance Indicator
    Maintenance required reminder light
    OFF or ON
    *6
    Master Warning*10
    Master warning light
    OFF or ON
    -
    Indicat. SET
    SET indicator light
    OFF or ON
    -
    Indicat. VSC OFF
    VSC off indicator light
    OFF or ON
    -
    Cruise Indicator*9
    Cruise control indicator light (amber)
    OFF or ON
    *7
    Turn Signal (Left) Indicator
    Turn LH indicator light
    OFF or ON
    -
    Turn Signal (Right) Indicator
    Turn RH indicator light
    OFF or ON
    -
    Smart System Indicator*4
    Smart entry and start system warning light (green)
    OFF or ON
    -
    Smart System Warning*4
    Smart entry and start system warning light (orange)
    OFF or ON
    *8
    Blind Spot Monitor Indicator*5
    Blind spot monitor indicator light
    OFF or ON
    *6
    Water Temperature Meter Operation
    Engine coolant temperature receiver gauge
    OFF, LOW, NORMAL, HIGH
    -
    Meter Display 1
    Multi-information display
    OFF, 6, 5, 4, 3, 2, 1, 0, All
    -
    Meter Display 2
    All dots in the ODO/TRIP meter
    OFF, 9, 8, 7
    -

    1. *1: w/ Rear Fog Light
    2. *2: w/ AFS (Adaptive Front-lighting System)
    3. *3: w/ Tire Pressure Warning System
    4. *4: w/ Smart Entry and Start System
    5. *5: w/ Blind Spot Monitor System
    6. *6: Although the item is displayed on the intelligent tester, no warning light or indicator light is operated.
    7. *7: The cruise control indicator light (amber) can be operated by selecting this item.
    8. *8: The smart entry and start system warning light (orange) can be operated by selecting this item.
    9. *9: w/ Cruise Control System
    10. *10: w/ Multi-information Display