Home › Vehicle Interior › METER / GAUGE / DISPLAY › METER / GAUGE SYSTEM

METER / GAUGE SYSTEM > Fuel Receiver Gauge Malfunction

for Preparation Click here


DESCRIPTION

  1. The meter ECU uses the fuel sender gauge assembly to determine the level of the fuel in the fuel tank. The resistance of the fuel sender gauge will vary between approximately 13 Ω with the float at the full position, and 414 Ω with the float at the empty position. The meter outputs battery voltage through two resistors that are mounted inside the meter ECU. The meter ECU measures the voltage between the variable resistor in the fuel sender gauge and the two resistors mounted in the meter. Voltage measured at this point will vary as the float of the fuel sender gauge is moved. The highest voltage observed should be approximately half of the battery voltage.

HINT:
The fuel level warning light will come on when the fuel level is below 10.5 liters (11.1 US qts, 9.2 Imp. qts).


WIRING DIAGRAM


E156126E40


INSPECTION PROCEDURE

1.PERFORM ACTIVE TEST USING INTELLIGENT TESTER (FUEL METER OPERATION)
  1. Connect the intelligent tester to the DLC3.

  1. Turn the ignition switch to ON.

  1. Turn the intelligent tester on.

  1. Enter following menus: Body / Combination Meter / Active Test.

  1. Check the operation by referring to the table below.

    Combination Meter 
    Tester Display
    Test Part
    Control Range
    Diagnostic Note
    Fuel Meter Operation
    Fuel receiver gauge
    Empty, 1/2, Full
    -

    OK:
    Fuel receiver gauge indication is normal.



NG
REPLACE COMBINATION METER ASSEMBLY (Click here)
OK


2.READ VALUE USING INTELLIGENT TESTER (FUEL INPUT)
  1. Connect the intelligent tester to the DLC3.

  1. Turn the ignition switch to ON.

  1. Turn the intelligent tester on.

  1. Enter following menus: Body / Combination Meter / Data List.

  1. Check the values by referring to the table below.

    Combination Meter 
    Tester Display
    Measurement Item/Range
    Normal Condition
    Diagnostic Note
    Fuel Input
    Fuel input/Min.: 0, Max.: 127.5
    Fuel receiver gauge indicates F: 57.0
    Unit: Liter
    Fuel receiver gauge indicates 3/4: 48.3
    Fuel receiver gauge indicates 1/2: 32.2
    Fuel receiver gauge indicates 1/4: 16.1
    Fuel receiver gauge indicates E: 6.4

    Result:

    Result
    Proceed to
    Fuel level data displayed on the intelligent tester is almost same as the fuel receiver gauge indication.
    A
    Fuel level data displayed on the intelligent tester differs from the fuel receiver gauge indication.
    B



B
REPLACE COMBINATION METER ASSEMBLY (Click here)
A


3.CHECK HARNESS AND CONNECTOR (COMBINATION METER ASSEMBLY - FUEL SUCTION TUBE ASSEMBLY WITH PUMP AND GAUGE)
  1. Disconnect the I18 combination meter assembly and N11 fuel suction tube assembly with pump and gauge connectors.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    I18-18 (FR) - N11-2 (FS)
    Always
    Below 1 Ω
    I18-17 (FE) - N11-3 (FE)
    Always
    Below 1 Ω
    I18-18 (FR) - Body ground
    Always
    10 kΩ or higher
    I18-17 (FE) - Body ground
    Always
    10 kΩ or higher



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK


4.INSPECT FUEL SENDER GAUGE ASSEMBLY


    E224291E01
  1. Remove the fuel sender gauge assembly (Click here for 2AR-FE, Click here for 2GR-FE).

  1. Check that the float moves smoothly between F and E.

  1. Check if the fuel sender gauge arm is deformed.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    1 - 2
    Float level is F (upper)
    13.5 to 16.5 Ω
    1 - 2
    Float level is between F (upper) and E (lower)
    13.5 to 414.5 Ω (Gradually changes)
    1 - 2
    Float level is E (lower)
    405.5 to 414.5 Ω

    Result:
    Result
    Proceed to
    OK
    A
    NG (for 2AR-FE)
    B
    NG (for 2GR-FE)
    C

    Text in Illustration 
    *a
    Front view of wire harness connector
    (to Fuel Sender Gauge Assembly)



B
REPLACE FUEL SENDER GAUGE ASSEMBLY (for 2AR-FE) (Click here)

C
REPLACE FUEL SENDER GAUGE ASSEMBLY (for 2GR-FE) (Click here)
A

REPLACE COMBINATION METER ASSEMBLY (Click here)