Home › Vehicle Exterior › WINDOW / GLASS › POWER WINDOW CONTROL SYSTEM

POWER WINDOW CONTROL SYSTEM > TERMINALS OF ECU

for Preparation Click here



MULTIPLEX NETWORK MASTER SWITCH ASSEMBLY


  1. Disconnect the K3*1 or J3*2 multiplex network master switch assembly connector.

    1. *1: for LHD
    2. *2: for RHD

    B150964E45


    Text in Illustration 
    *A
    for LHD
    *B
    for RHD

  2. Measure the voltage and resistance according to the value(s) in the table below.

    HINT:
    Measure the values on the wire harness side with the connector disconnected.


    for LHD 
    Tester Connection
    Wiring Color
    Terminal Description
    Condition
    Specified Condition
    K3-11 (B) - K3-12 (GND)
    W - BR
    Power supply
    Always
    11 to 14 V
    K3-12 (GND) - Body ground
    BR - Body ground
    Ground
    Always
    Below 1 Ω

    for RHD 
    Tester Connection
    Wiring Color
    Terminal Description
    Condition
    Specified Condition
    J3-11 (B) - J3-12 (GND)
    W - BR
    Power supply
    Always
    11 to 14 V
    J3-12 (GND) - Body ground
    BR - Body ground
    Ground
    Always
    Below 1 Ω
    If the result is not as specified, there may be a malfunction in the wire harness.

  3. Reconnect the K3*1 or J3*2 multiplex network master switch assembly connector.

    1. *1: for LHD
    2. *2: for RHD

  4. Measure the voltage according to the value(s) in the table below.

    for LHD 
    Tester Connection
    Wiring Color
    Terminal Description
    Condition
    Specified Condition
    K3-15 (DOWN) - K3-12 (GND)
    R - BR
    Power window motor DOWN output
    Ignition switch ON, driver door power window regulator switch not pushed or pulled
    11 to 14 V
    K3-15 (DOWN) - K3-12 (GND)
    R - BR
    Power window motor DOWN output
    Ignition switch ON, driver door power window moving, driver door power window regulator switch pushed halfway down (Manual operation)
    Below 1 V
    K3-18 (LED) - K3-12 (GND)
    Y - BR
    LED illumination signal
    Ignition switch ON
    11 to 14 V
    K3-18 (LED) - K3-12 (GND)
    Y - BR
    LED illumination signal
    Approximately 43 seconds after ignition switch turned off
    Below 1 V
    K3-20 (UP) - K3-12 (GND)
    G - BR
    Power window motor UP output
    Ignition switch ON, driver door power window regulator switch not pushed or pulled
    11 to 14 V
    K3-20 (UP) - K3-12 (GND)
    G - BR
    Power window motor UP output
    Ignition switch ON, driver door power window moving, driver door power window regulator switch pulled halfway up (Manual operation)
    Below 1 V

    for RHD 
    Tester Connection
    Wiring Color
    Terminal Description
    Condition
    Specified Condition
    J3-15 (DOWN) - J3-12 (GND)
    R - BR
    Power window motor DOWN output
    Ignition switch ON, driver door power window regulator switch not pushed or pulled
    11 to 14 V
    J3-15 (DOWN) - J3-12 (GND)
    R - BR
    Power window motor DOWN output
    Ignition switch ON, driver door power window moving, driver door power window regulator switch pushed halfway down (Manual operation)
    Below 1 V
    J3-18 (LED) - J3-12 (GND)
    Y - BR
    LED illumination signal
    Ignition switch ON
    11 to 14 V
    J3-18 (LED) - J3-12 (GND)
    Y - BR
    LED illumination signal
    Approximately 43 seconds after ignition switch turned off
    Below 1 V
    J3-20 (UP) - J3-12 (GND)
    G - BR
    Power window motor UP output
    Ignition switch ON, driver door power window regulator switch not pushed or pulled
    11 to 14 V
    J3-20 (UP) - J3-12 (GND)
    G - BR
    Power window motor UP output
    Ignition switch ON, driver door power window moving, driver door power window regulator switch pulled halfway up (Manual operation)
    Below 1 V
    If the result is not as specified, the multiplex network master switch assembly may have a malfunction.


CHECK POWER WINDOW REGULATOR SWITCH ASSEMBLY


  1. Disconnect the J4*1 or K4*2 power window regulator switch assembly connector.

    1. *1: for LHD
    2. *2: for RHD

    B176174E55


    Text in Illustration 
    *A
    for LHD
    *B
    for RHD

  2. Measure the resistance according to the value(s) in the table below.

    HINT:
    Measure the values on the wire harness side with the connector disconnected.


    for LHD 
    Tester Connection
    Wiring Color
    Terminal Description
    Condition
    Specified Condition
    J4-1 (GND) - Body ground
    BR - Body ground
    Ground
    Always
    Below 1 Ω

    for RHD 
    Tester Connection
    Wiring Color
    Terminal Description
    Condition
    Specified Condition
    K4-1 (GND) - Body ground
    BR - Body ground
    Ground
    Always
    Below 1 Ω
    If the result is not as specified, there may be a malfunction in the wire harness.

  3. Reconnect the J4*1 or K4*2 power window regulator switch assembly connector.

    1. *1: for LHD
    2. *2: for RHD

  4. Measure the voltage according to the value(s) in the table below.

    for LHD 
    Tester Connection
    Wiring Color
    Terminal Description
    Condition
    Specified Condition
    J4-4 (LED) - J4-1 (GND)
    Y - BR
    LED illumination signal
    Ignition switch ON
    11 to 14 V
    J4-4 (LED) - J4-1 (GND)
    Y - BR
    LED illumination signal
    Approximately 43 seconds after the ignition switch turned off
    Below 1 V
    J4-6 (UP) - J4-1 (GND)
    BE - BR
    Power window motor UP output
    Ignition switch ON, power window regulator switch assembly not pushed or pulled
    11 to 14 V
    J4-6 (UP) - J4-1 (GND)
    BE - BR
    Power window motor UP output
    Ignition switch ON, front passenger door power window moving, power window regulator switch assembly pulled halfway up (Manual operation)
    Below 1 V
    J4-6 (UP) - J4-1 (GND)
    BE - BR
    Power window motor UP output
    Ignition switch ON, front passenger door power window fully open
    11 to 14 V
    J4-6 (UP) - J4-1 (GND)
    BE - BR
    Power window motor UP output
    Ignition switch ON, front passenger door power window moving, power window regulator switch assembly fully pulled up (Automatic operation)
    Below 1 V
    J4-6 (UP) - J4-1 (GND)
    BE - BR
    Power window motor UP output
    Ignition switch ON, front passenger door power window fully closed
    11 to 14 V
    J4-7 (DOWN) - J4-1 (GND)
    V - BR
    Power window motor DOWN output
    Ignition switch ON, power window regulator switch assembly not pushed or pulled
    11 to 14 V
    J4-7 (DOWN) - J4-1 (GND)
    V - BR
    Power window motor DOWN output
    Ignition switch ON, front passenger door power window moving, power window regulator switch assembly pushed halfway down (Manual operation)
    Below 1 V
    J4-7 (DOWN) - J4-1 (GND)
    V - BR
    Power window motor DOWN output
    Ignition switch ON, front passenger door power window fully closed
    11 to 14 V
    J4-7 (DOWN) - J4-1 (GND)
    V - BR
    Power window motor DOWN output
    Ignition switch ON, front passenger door power window moving, power window regulator switch assembly fully pushed down (Automatic operation)
    Below 1 V
    J4-7 (DOWN) - J4-1 (GND)
    V - BR
    Power window motor DOWN output
    Ignition switch ON, front passenger door power window fully open
    11 to 14 V
    J4-8 (AUTO) - J4-1 (GND)
    L - BR
    Power window motor AUTO UP output
    Ignition switch ON, front passenger door power window fully open
    11 to 14 V
    J4-8 (AUTO) - J4-1 (GND)
    L - BR
    Power window motor AUTO UP output
    Ignition switch ON, front passenger door power window moving, power window regulator switch assembly fully pulled up (Automatic operation)
    Below 1 V
    J4-8 (AUTO) - J4-1 (GND)
    L - BR
    Power window motor AUTO UP output
    Ignition switch ON, front passenger door power window fully closed
    11 to 14 V
    J4-8 (AUTO) - J4-1 (GND)
    L - BR
    Power window motor AUTO DOWN output
    Ignition switch ON, front passenger door power window fully closed
    11 to 14 V
    J4-8 (AUTO) - J4-1 (GND)
    L - BR
    Power window motor AUTO DOWN output
    Ignition switch ON, front passenger door power window moving, power window regulator switch assembly fully pushed down (Automatic operation)
    Below 1 V
    J4-8 (AUTO) - J4-1 (GND)
    L - BR
    Power window motor AUTO DOWN output
    Ignition switch ON, front passenger door power window fully open
    11 to 14 V

    for RHD 
    Tester Connection
    Wiring Color
    Terminal Description
    Condition
    Specified Condition
    K4-4 (LED) - K4-1 (GND)
    Y - BR
    LED illumination signal
    Ignition switch ON
    11 to 14 V
    K4-4 (LED) - K4-1 (GND)
    Y - BR
    LED illumination signal
    Approximately 43 seconds after the ignition switch turned off
    Below 1 V
    K4-6 (UP) - K4-1 (GND)
    G - BR
    Power window motor UP output
    Ignition switch ON, power window regulator switch assembly not pushed or pulled
    11 to 14 V
    K4-6 (UP) - K4-1 (GND)
    G - BR
    Power window motor UP output
    Ignition switch ON, front passenger door power window moving, power window regulator switch assembly pulled halfway up (Manual operation)
    Below 1 V
    K4-6 (UP) - K4-1 (GND)
    G - BR
    Power window motor UP output
    Ignition switch ON, front passenger door power window fully open
    11 to 14 V
    K4-6 (UP) - K4-1 (GND)
    G - BR
    Power window motor UP output
    Ignition switch ON, front passenger door power window moving, power window regulator switch assembly fully pulled up (Automatic operation)
    Below 1 V
    K4-6 (UP) - K4-1 (GND)
    G - BR
    Power window motor UP output
    Ignition switch ON, front passenger door power window fully closed
    11 to 14 V
    K4-7 (DOWN) - K4-1 (GND)
    V - BR
    Power window motor DOWN output
    Ignition switch ON, power window regulator switch assembly not pushed or pulled
    11 to 14 V
    K4-7 (DOWN) - K4-1 (GND)
    V - BR
    Power window motor DOWN output
    Ignition switch ON, front passenger door power window moving, power window regulator switch assembly pushed halfway down (Manual operation)
    Below 1 V
    K4-7 (DOWN) - K4-1 (GND)
    V - BR
    Power window motor DOWN output
    Ignition switch ON, front passenger door power window fully closed
    11 to 14 V
    K4-7 (DOWN) - K4-1 (GND)
    V - BR
    Power window motor DOWN output
    Ignition switch ON, front passenger door power window moving, power window regulator switch assembly fully pushed down (Automatic operation)
    Below 1 V
    K4-7 (DOWN) - K4-1 (GND)
    V - BR
    Power window motor DOWN output
    Ignition switch ON, front passenger door power window fully open
    11 to 14 V
    K4-8 (AUTO) - K4-1 (GND)
    L - BR
    Power window motor AUTO UP output
    Ignition switch ON, front passenger door power window fully open
    11 to 14 V
    K4-8 (AUTO) - K4-1 (GND)
    L - BR
    Power window motor AUTO UP output
    Ignition switch ON, front passenger door power window moving, power window regulator switch assembly fully pulled up (Automatic operation)
    Below 1 V
    K4-8 (AUTO) - K4-1 (GND)
    L - BR
    Power window motor AUTO UP output
    Ignition switch ON, front passenger door power window fully closed
    11 to 14 V
    K4-8 (AUTO) - K4-1 (GND)
    L - BR
    Power window motor AUTO DOWN output
    Ignition switch ON, front passenger door power window fully closed
    11 to 14 V
    K4-8 (AUTO) - K4-1 (GND)
    L - BR
    Power window motor AUTO DOWN output
    Ignition switch ON, front passenger door power window moving, power window regulator switch assembly fully pushed down (Automatic operation)
    Below 1 V
    K4-8 (AUTO) - K4-1 (GND)
    L - BR
    Power window motor AUTO DOWN output
    Ignition switch ON, front passenger door power window fully open
    11 to 14 V
    If the result is not as specified, the power window regulator switch assembly may have a malfunction.


CHECK REAR POWER WINDOW REGULATOR SWITCH ASSEMBLY (for LH Door)


  1. Disconnect the M4 rear power window regulator switch assembly (for LH door) connector.


    B176174E50

  2. Measure the resistance according to the value(s) in the table below.

    HINT:
    Measure the values on the wire harness side with the connector disconnected.


    Tester Connection
    Wiring Color
    Terminal Description
    Condition
    Specified Condition
    M4-1 (GND) - Body ground
    BR - Body ground
    Ground
    Always
    Below 1 Ω
    If the result is not as specified, there may be a malfunction in the wire harness.

  3. Reconnect the M4 rear power window regulator switch assembly (for LH door) connector.

  4. Measure the voltage according to the value(s) in the table below.

    Tester Connection
    Wiring Color
    Terminal Description
    Condition
    Specified Condition
    M4-4 (LED) - M4-1 (GND)
    LG - BR
    LED illumination signal
    Ignition switch ON
    11 to 14 V
    M4-4 (LED) - M4-1 (GND)
    LG - BR
    LED illumination signal
    Approximately 43 seconds after the ignition switch turned off
    Below 1 V
    M4-6 (UP) - M4-1 (GND)
    G - BR
    Power window motor UP output
    Ignition switch ON, rear power window regulator switch assembly (for LH door) not pushed or pulled
    11 to 14 V
    M4-6 (UP) - M4-1 (GND)
    G - BR
    Power window motor UP output
    Ignition switch ON, rear LH door power window moving, rear power window regulator switch assembly (for LH door) pulled halfway up (Manual operation)
    Below 1 V
    M4-6 (UP) - M4-1 (GND)
    G - BR
    Power window motor UP output
    Ignition switch ON, rear LH door power window fully open
    11 to 14 V
    M4-6 (UP) - M4-1 (GND)
    G - BR
    Power window motor UP output
    Ignition switch ON, rear LH door power window moving, rear power window regulator switch assembly (for LH door) fully pulled up (Automatic operation)
    Below 1 V
    M4-6 (UP) - M4-1 (GND)
    G - BR
    Power window motor UP output
    Ignition switch ON, rear LH door power window fully closed
    11 to 14 V
    M4-7 (DOWN) - M4-1 (GND)
    R - BR
    Power window motor DOWN output
    Ignition switch ON, rear power window regulator switch assembly (for LH door) not pushed or pulled
    11 to 14 V
    M4-7 (DOWN) - M4-1 (GND)
    R - BR
    Power window motor DOWN output
    Ignition switch ON, rear LH door power window moving, rear power window regulator switch assembly (for LH door) pushed halfway down (Manual operation)
    Below 1 V
    M4-7 (DOWN) - M4-1 (GND)
    R - BR
    Power window motor DOWN output
    Ignition switch ON, rear LH door power window fully closed
    11 to 14 V
    M4-7 (DOWN) - M4-1 (GND)
    R - BR
    Power window motor DOWN output
    Ignition switch ON, rear LH door power window moving, rear power window regulator switch assembly (for LH door) fully pushed down (Automatic operation)
    Below 1 V
    M4-7 (DOWN) - M4-1 (GND)
    R - BR
    Power window motor DOWN output
    Ignition switch ON, rear LH door power window fully open
    11 to 14 V
    M4-8 (AUTO) - M4-1 (GND)
    B - BR
    Power window motor AUTO UP output
    Ignition switch ON, rear LH door power window fully open
    11 to 14 V
    M4-8 (AUTO) - M4-1 (GND)
    B - BR
    Power window motor AUTO UP output
    Ignition switch ON, rear LH door power window moving, rear power window regulator switch assembly (for LH door) fully pulled up (Automatic operation)
    Below 1 V
    M4-8 (AUTO) - M4-1 (GND)
    B - BR
    Power window motor AUTO UP output
    Ignition switch ON, rear LH door power window fully closed
    11 to 14 V
    M4-8 (AUTO) - M4-1 (GND)
    B - BR
    Power window motor AUTO DOWN output
    Ignition switch ON, rear LH door power window fully closed
    11 to 14 V
    M4-8 (AUTO) - M4-1 (GND)
    B - BR
    Power window motor AUTO DOWN output
    Ignition switch ON, rear LH door power window moving, rear power window regulator switch assembly (for LH door) fully pushed down (Automatic operation)
    Below 1 V
    M4-8 (AUTO) - M4-1 (GND)
    B - BR
    Power window motor AUTO DOWN output
    Ignition switch ON, rear LH door power window fully open
    11 to 14 V
    If the result is not as specified, the rear power window regulator switch assembly (for LH door) may have a malfunction.


CHECK REAR POWER WINDOW REGULATOR SWITCH ASSEMBLY (for RH Door)


  1. Disconnect the L4 rear power window regulator switch assembly (for RH door) connector.


    B176174E51

  2. Measure the resistance according to the value(s) in the table below.

    HINT:
    Measure the values on the wire harness door with the connector disconnected.


    Tester Connection
    Wiring Color
    Terminal Description
    Condition
    Specified Condition
    L4-1 (GND) - Body ground
    BR - Body ground
    Ground
    Always
    Below 1 Ω
    If the result is not as specified, there may be a malfunction in the wire harness.

  3. Reconnect the L4 rear power window regulator switch assembly (for RH door) connector.

  4. Measure the voltage according to the value(s) in the table below.

    Tester Connection
    Wiring Color
    Terminal Description
    Condition
    Specified Condition
    L4-4 (LED) - L4-1 (GND)
    LG - BR
    LED illumination signal
    Ignition switch ON
    11 to 14 V
    L4-4 (LED) - L4-1 (GND)
    LG - BR
    LED illumination signal
    Approximately 43 seconds after the ignition switch turned off
    Below 1 V
    L4-6 (UP) - L4-1 (GND)
    G - BR
    Power window motor UP output
    Ignition switch ON, rear power window regulator switch assembly (for RH door) not pushed or pulled
    11 to 14 V
    L4-6 (UP) - L4-1 (GND)
    G - BR
    Power window motor UP output
    Ignition switch ON, rear RH door power window moving, rear power window regulator switch assembly (for RH door) pulled halfway up (Manual operation)
    Below 1 V
    L4-6 (UP) - L4-1 (GND)
    G - BR
    Power window motor UP output
    Ignition switch ON, rear RH door power window fully open
    11 to 14 V
    L4-6 (UP) - L4-1 (GND)
    G - BR
    Power window motor UP output
    Ignition switch ON, rear RH door power window moving, rear power window regulator switch assembly (for RH door) fully pulled up (Automatic operation)
    Below 1 V
    L4-6 (UP) - L4-1 (GND)
    G - BR
    Power window motor UP output
    Ignition switch ON, rear RH door power window fully closed
    11 to 14 V
    L4-7 (DOWN) - L4-1 (GND)
    R - BR
    Power window motor DOWN output
    Ignition switch ON, rear power window regulator switch assembly (for RH door) not pushed or pulled
    11 to 14 V
    L4-7 (DOWN) - L4-1 (GND)
    R - BR
    Power window motor DOWN output
    Ignition switch ON, rear RH door power window moving, rear power window regulator switch assembly (for RH door) pushed halfway down (Manual operation)
    Below 1 V
    L4-7 (DOWN) - L4-1 (GND)
    R - BR
    Power window motor DOWN output
    Ignition switch ON, rear RH door power window fully closed
    11 to 14 V
    L4-7 (DOWN) - L4-1 (GND)
    R - BR
    Power window motor DOWN output
    Ignition switch ON, rear RH door power window moving, rear power window regulator switch assembly (for RH door) fully pushed down (Automatic operation)
    Below 1 V
    L4-7 (DOWN) - L4-1 (GND)
    R - BR
    Power window motor DOWN output
    Ignition switch ON, rear RH door power window fully open
    11 to 14 V
    L4-8 (AUTO) - L4-1 (GND)
    B - BR
    Power window motor AUTO UP output
    Ignition switch ON, rear RH door power window fully open
    11 to 14 V
    L4-8 (AUTO) - L4-1 (GND)
    B - BR
    Power window motor AUTO UP output
    Ignition switch ON, rear RH door power window moving, rear power window regulator switch assembly (for RH door) fully pulled up (Automatic operation)
    Below 1 V
    L4-8 (AUTO) - L4-1 (GND)
    B - BR
    Power window motor AUTO UP output
    Ignition switch ON, rear RH door power window fully closed
    11 to 14 V
    L4-8 (AUTO) - L4-1 (GND)
    B - BR
    Power window motor AUTO DOWN output
    Ignition switch ON, rear RH door power window fully closed
    11 to 14 V
    L4-8 (AUTO) - L4-1 (GND)
    B - BR
    Power window motor AUTO DOWN output
    Ignition switch ON, rear RH door power window moving, rear power window regulator switch assembly (for RH door) fully pushed down (Automatic operation)
    Below 1 V
    L4-8 (AUTO) - L4-1 (GND)
    B - BR
    Power window motor AUTO DOWN output
    Ignition switch ON, rear RH door power window fully open
    11 to 14 V
    If the result is not as specified, the rear power window regulator switch assembly (for RH door) may have a malfunction.


CHECK POWER WINDOW REGULATOR MOTOR ASSEMBLY (for Driver Door)


  1. Disconnect the K9*1 or J9*2 power window regulator motor assembly (for driver door) connector.

    1. *1: for LHD
    2. *2: for RHD

    B280976E02


    Text in Illustration 
    *A
    for LHD
    *B
    for RHD

  2. Measure the voltage and resistance according to the value(s) in the table below.

    HINT:
    Measure the values on the wire harness door with the connector disconnected.


    for LHD 
    Tester Connection
    Wiring Color
    Terminal Description
    Condition
    Specified Condition
    K9-1 (GND) - Body ground
    W-B - Body ground
    Ground
    Always
    Below 1 Ω
    K9-2 (B) - Body ground
    GR - Body ground
    Power supply
    Always
    11 to 14 V

    for RHD 
    Tester Connection
    Wiring Color
    Terminal Description
    Condition
    Specified Condition
    J9-1 (GND) - Body ground
    W-B - Body ground
    Ground
    Always
    Below 1 Ω
    J9-2 (B) - Body ground
    GR - Body ground
    Power supply
    Always
    11 to 14 V
    If the result is not as specified, there may be a malfunction in the wire harness.

  3. Reconnect the K9*1 or J9*2 power window regulator motor assembly (for driver door) connector.

    1. *1: for LHD
    2. *2: for RHD

  4. Measure the voltage according to the value(s) in the table below.

    for LHD 
    Tester Connection
    Wiring Color
    Terminal Description
    Condition
    Specified Condition
    K9-5 (LED) - K9-1 (GND)
    Y - W-B
    LED illumination signal
    Ignition switch ON
    11 to 14 V
    K9-5 (LED) - K9-1 (GND)
    Y - W-B
    LED illumination signal
    Approximately 43 seconds after ignition switch turned off
    Below 1 V
    K9-7 (DOWN) - K9-1 (GND)
    R - W-B
    Power window motor DOWN input
    Ignition switch ON, multiplex network master switch assembly (driver door power window regulator switch) not pushed or pulled
    11 to 14 V
    K9-7 (DOWN) - K9-1 (GND)
    R - W-B
    Power window motor DOWN input
    Ignition switch ON, driver door power window moving, multiplex network master switch assembly (driver door power window regulator switch) pushed halfway down (Manual operation)
    Below 1 V
    K9-7 (DOWN) - K9-1 (GND)
    R - W-B
    Power window motor DOWN input
    Ignition switch ON, driver door power window fully closed
    11 to 14 V
    K9-7 (DOWN) - K9-1 (GND)
    R - W-B
    Power window motor DOWN input
    Ignition switch ON, driver door power window moving, multiplex network master switch assembly (driver door power window regulator switch) fully pushed down (Automatic operation)
    Below 1 V
    K9-7 (DOWN) - K9-1 (GND)
    R - W-B
    Power window motor AUTO DOWN input
    Ignition switch ON, driver door power window fully open
    11 to 14 V
    K9-10 (UP) - K9-1 (GND)
    G - W-B
    Power window motor UP input
    Ignition switch ON, multiplex network master switch assembly (driver door power window regulator switch) not pushed or pulled
    11 to 14 V
    K9-10 (UP) - K9-1 (GND)
    G - W-B
    Power window motor UP input
    Ignition switch ON, driver door power window moving, multiplex network master switch assembly (driver door power window regulator switch) pulled halfway up (Manual operation)
    Below 1 V
    K9-10 (UP) - K9-1 (GND)
    G - W-B
    Power window motor UP input
    Ignition switch ON, multiplex network master switch assembly (driver door power window regulator switch) fully open
    11 to 14 V
    K9-10 (UP) - K9-1 (GND)
    G - W-B
    Power window motor UP input
    Ignition switch ON, driver door power window moving, multiplex network master switch assembly (driver door power window regulator switch) fully pulled up (Automatic operation)
    Below 1 V
    K9-10 (UP) - K9-1 (GND)
    G - W-B
    Power window motor UP input
    Ignition switch ON, driver door power window fully closed
    11 to 14 V

    for RHD 
    Tester Connection
    Wiring Color
    Terminal Description
    Condition
    Specified Condition
    J9-5 (LED) - J9-1 (GND)
    Y - W-B
    LED illumination signal
    Ignition switch ON
    11 to 14 V
    J9-5 (LED) - J9-1 (GND)
    Y - W-B
    LED illumination signal
    Approximately 43 seconds after ignition switch turned off
    Below 1 V
    J9-7 (DOWN) - J9-1 (GND)
    R - W-B
    Power window motor DOWN input
    Ignition switch ON, multiplex network master switch assembly (driver door power window regulator switch) not pushed or pulled
    11 to 14 V
    J9-7 (DOWN) - J9-1 (GND)
    R - W-B
    Power window motor DOWN input
    Ignition switch ON, driver door power window moving, multiplex network master switch assembly (driver door power window regulator switch) pushed halfway down (Manual operation)
    Below 1 V
    J9-7 (DOWN) - J9-1 (GND)
    R - W-B
    Power window motor DOWN input
    Ignition switch ON, driver door power window fully closed
    11 to 14 V
    J9-7 (DOWN) - J9-1 (GND)
    R - W-B
    Power window motor DOWN input
    Ignition switch ON, driver door power window moving, multiplex network master switch assembly (driver door power window regulator switch) fully pushed down (Automatic operation)
    Below 1 V
    J9-7 (DOWN) - J9-1 (GND)
    R - W-B
    Power window motor AUTO DOWN input
    Ignition switch ON, driver door power window fully open
    11 to 14 V
    J9-10 (UP) - J9-1 (GND)
    G - W-B
    Power window motor UP input
    Ignition switch ON, multiplex network master switch assembly (driver door power window regulator switch) not pushed or pulled
    11 to 14 V
    J9-10 (UP) - J9-1 (GND)
    G - W-B
    Power window motor UP input
    Ignition switch ON, driver door power window moving, multiplex network master switch assembly (driver door power window regulator switch) pulled halfway up (Manual operation)
    Below 1 V
    J9-10 (UP) - J9-1 (GND)
    G - W-B
    Power window motor UP input
    Ignition switch ON, multiplex network master switch assembly (driver door power window regulator switch) fully open
    11 to 14 V
    J9-10 (UP) - J9-1 (GND)
    G - W-B
    Power window motor UP input
    Ignition switch ON, driver door power window moving, multiplex network master switch assembly (driver door power window regulator switch) fully pulled up (Automatic operation)
    Below 1 V
    J9-10 (UP) - J9-1 (GND)
    G - W-B
    Power window motor UP input
    Ignition switch ON, driver door power window fully closed
    11 to 14 V
    If the result is not as specified, the power window regulator motor assembly (for driver door) may have a malfunction.


CHECK POWER WINDOW REGULATOR MOTOR ASSEMBLY (for Front Passenger Door)


  1. Disconnect the J9*1 or K9*2 power window regulator motor assembly (for front passenger door) connector.

    1. *1: for LHD
    2. *2: for RHD

    B280976E05


    Text in Illustration 
    *A
    for LHD
    *B
    for RHD

  2. Measure the voltage and resistance according to the value(s) in the table below.

    HINT:
    Measure the values on the wire harness door with the connector disconnected.


    for LHD 
    Tester Connection
    Wiring Color
    Terminal Description
    Condition
    Specified Condition
    J9-1 (GND) - Body ground
    W-B - Body ground
    Ground
    Always
    Below 1 Ω
    J9-2 (B) - Body ground
    GR - Body ground
    Power supply
    Always
    11 to 14 V

    for RHD 
    Tester Connection
    Wiring Color
    Terminal Description
    Condition
    Specified Condition
    K9-1 (GND) - Body ground
    W-B - Body ground
    Ground
    Always
    Below 1 Ω
    K9-2 (B) - Body ground
    GR - Body ground
    Power supply
    Always
    11 to 14 V
    If the result is not as specified, there may be a malfunction in the wire harness.

  3. Reconnect the J9*1 or K9*2 power window regulator motor assembly (for front passenger door) connector.

    1. *1: for LHD
    2. *2: for RHD

  4. Measure the voltage according to the value(s) in the table below.

    for LHD 
    Tester Connection
    Wiring Color
    Terminal Description
    Condition
    Specified Condition
    J9-4 (AUTO) - J9-1 (GND)
    L - W-B
    Power window motor AUTO UP input
    Ignition switch ON, front passenger door power window fully open
    11 to 14 V
    J9-4 (AUTO) - J9-1 (GND)
    L - W-B
    Power window motor AUTO UP input
    Ignition switch ON, front passenger door power window moving, power window regulator switch assembly fully pulled up (Automatic operation)
    Below 1 V
    J9-4 (AUTO) - J9-1 (GND)
    L - W-B
    Power window motor AUTO UP input
    Ignition switch ON, front passenger door power window fully closed
    11 to 14 V
    J9-4 (AUTO) - J9-1 (GND)
    L - W-B
    Power window motor AUTO DOWN input
    Ignition switch ON, front passenger door power window fully closed
    11 to 14 V
    J9-4 (AUTO) - J9-1 (GND)
    L - W-B
    Power window motor AUTO DOWN input
    Ignition switch ON, front passenger door power window moving, power window regulator switch assembly fully pushed down (Automatic operation)
    Below 1 V
    J9-4 (AUTO) - J9-1 (GND)
    L - W-B
    Power window motor AUTO DOWN input
    Ignition switch ON, front passenger door power window fully open
    11 to 14 V
    J9-5 (LED) - J9-1 (GND)
    Y - W-B
    LED illumination signal
    Ignition switch ON
    11 to 14 V
    J9-5 (LED) - J9-1 (GND)
    Y - W-B
    LED illumination signal
    Approximately 43 seconds after ignition switch turned off
    Below 1 V
    J9-7 (DOWN) - J9-1 (GND)
    V - W-B
    Power window motor DOWN input
    Ignition switch ON, power window regulator switch assembly not pushed or pulled
    11 to 14 V
    J9-7 (DOWN) - J9-1 (GND)
    V - W-B
    Power window motor DOWN input
    Ignition switch ON, front passenger door power window moving, power window regulator switch assembly pushed halfway down (Manual operation)
    Below 1 V
    J9-7 (DOWN) - J9-1 (GND)
    V - W-B
    Power window motor DOWN input
    Ignition switch ON, front passenger door power window fully closed
    11 to 14 V
    J9-7 (DOWN) - J9-1 (GND)
    V - W-B
    Power window motor DOWN input
    Ignition switch ON, front passenger door power window moving, power window regulator switch assembly fully pushed down (Automatic operation)
    Below 1 V
    J9-7 (DOWN) - J9-1 (GND)
    V - W-B
    Power window motor DOWN input
    Ignition switch ON, front passenger door power window fully open
    11 to 14 V
    J9-10 (UP) - J9-1 (GND)
    BE - W-B
    Power window motor UP input
    Ignition switch ON, power window regulator switch assembly not pushed or pulled
    11 to 14 V
    J9-10 (UP) - J9-1 (GND)
    BE - W-B
    Power window motor UP input
    Ignition switch ON, front passenger door power window moving, power window regulator switch assembly pulled halfway up (Manual operation)
    Below 1 V
    J9-10 (UP) - J9-1 (GND)
    BE - W-B
    Power window motor UP input
    Ignition switch ON, front passenger door power window fully open
    11 to 14 V
    J9-10 (UP) - J9-1 (GND)
    BE - W-B
    Power window motor UP input
    Ignition switch ON, front passenger door power window moving, power window regulator switch assembly fully pulled up (Automatic operation)
    Below 1 V
    J9-10 (UP) - J9-1 (GND)
    BE - W-B
    Power window motor UP input
    Ignition switch ON, front passenger door power window fully closed
    11 to 14 V

    for RHD 
    Tester Connection
    Wiring Color
    Terminal Description
    Condition
    Specified Condition
    K9-4 (AUTO) - K9-1 (GND)
    L - W-B
    Power window motor AUTO UP input
    Ignition switch ON, front passenger door power window fully open
    11 to 14 V
    K9-4 (AUTO) - K9-1 (GND)
    L - W-B
    Power window motor AUTO UP input
    Ignition switch ON, front passenger door power window moving, power window regulator switch assembly fully pulled up (Automatic operation)
    Below 1 V
    K9-4 (AUTO) - K9-1 (GND)
    L - W-B
    Power window motor AUTO UP input
    Ignition switch ON, front passenger door power window fully closed
    11 to 14 V
    K9-4 (AUTO) - K9-1 (GND)
    L - W-B
    Power window motor AUTO DOWN input
    Ignition switch ON, front passenger door power window fully closed
    11 to 14 V
    K9-4 (AUTO) - K9-1 (GND)
    L - W-B
    Power window motor AUTO DOWN input
    Ignition switch ON, front passenger door power window moving, power window regulator switch assembly fully pushed down (Automatic operation)
    Below 1 V
    K9-4 (AUTO) - K9-1 (GND)
    L - W-B
    Power window motor AUTO DOWN input
    Ignition switch ON, front passenger door power window fully open
    11 to 14 V
    K9-5 (LED) - K9-1 (GND)
    Y - W-B
    LED illumination signal
    Ignition switch ON
    11 to 14 V
    K9-5 (LED) - K9-1 (GND)
    Y - W-B
    LED illumination signal
    Approximately 43 seconds after ignition switch turned off
    Below 1 V
    K9-7 (DOWN) - K9-1 (GND)
    V - W-B
    Power window motor DOWN input
    Ignition switch ON, power window regulator switch assembly not pushed or pulled
    11 to 14 V
    K9-7 (DOWN) - K9-1 (GND)
    V - W-B
    Power window motor DOWN input
    Ignition switch ON, front passenger door power window moving, power window regulator switch assembly pushed halfway down (Manual operation)
    Below 1 V
    K9-7 (DOWN) - K9-1 (GND)
    V - W-B
    Power window motor DOWN input
    Ignition switch ON, front passenger door power window fully closed
    11 to 14 V
    K9-7 (DOWN) - K9-1 (GND)
    V - W-B
    Power window motor DOWN input
    Ignition switch ON, front passenger door power window moving, power window regulator switch assembly fully pushed down (Automatic operation)
    Below 1 V
    K9-7 (DOWN) - K9-1 (GND)
    V - W-B
    Power window motor DOWN input
    Ignition switch ON, front passenger door power window fully open
    11 to 14 V
    K9-10 (UP) - K9-1 (GND)
    G - W-B
    Power window motor UP input
    Ignition switch ON, power window regulator switch assembly not pushed or pulled
    11 to 14 V
    K9-10 (UP) - K9-1 (GND)
    G - W-B
    Power window motor UP input
    Ignition switch ON, front passenger door power window moving, power window regulator switch assembly pulled halfway up (Manual operation)
    Below 1 V
    K9-10 (UP) - K9-1 (GND)
    G - W-B
    Power window motor UP input
    Ignition switch ON, front passenger door power window fully open
    11 to 14 V
    K9-10 (UP) - K9-1 (GND)
    G - W-B
    Power window motor UP input
    Ignition switch ON, front passenger door power window moving, power window regulator switch assembly fully pulled up (Automatic operation)
    Below 1 V
    K9-10 (UP) - K9-1 (GND)
    G - W-B
    Power window motor UP input
    Ignition switch ON, front passenger door power window fully closed
    11 to 14 V
    If the result is not as specified, the power window regulator motor assembly (for front passenger door) may have a malfunction.


CHECK POWER WINDOW REGULATOR MOTOR ASSEMBLY (for Rear LH Door)


  1. Disconnect the M2 power window regulator motor assembly (for rear LH door) connector.


    B286758E03

  2. Measure the voltage and resistance according to the value(s) in the table below.

    HINT:
    Measure the values on the wire harness side with the connector disconnected.


    Tester Connection
    Wiring Color
    Terminal Description
    Condition
    Specified Condition
    M2-1 (GND) - Body ground
    W-B - Body ground
    Ground
    Always
    Below 1 Ω
    M2-2 (B) - Body ground
    G - Body ground
    Power supply
    Always
    11 to 14 V
    If the result is not as specified, there may be a malfunction in the wire harness.

  3. Reconnect the M2 power window regulator motor assembly (for rear LH door) connector.

  4. Measure the voltage according to the value(s) in the table below.

    Tester Connection
    Wiring Color
    Terminal Description
    Condition
    Specified Condition
    M2-4 (AUTO) - M2-1 (GND)
    B - W-B
    Power window motor AUTO UP input
    Ignition switch ON, rear LH door power window fully open
    11 to 14 V
    M2-4 (AUTO) - M2-1 (GND)
    B - W-B
    Power window motor AUTO UP input
    Ignition switch ON, rear LH door power window moving, rear power window regulator switch assembly (for LH door) fully pulled up (Automatic operation)
    Below 1 V
    M2-4 (AUTO) - M2-1 (GND)
    B - W-B
    Power window motor AUTO UP input
    Ignition switch ON, rear LH door power window fully closed
    11 to 14 V
    M2-4 (AUTO) - M2-1 (GND)
    B - W-B
    Power window motor AUTO DOWN input
    Ignition switch ON, rear LH door power window fully closed
    11 to 14 V
    M2-4 (AUTO) - M2-1 (GND)
    B - W-B
    Power window motor AUTO DOWN input
    Ignition switch ON, rear LH door power window moving, rear power window regulator switch assembly (for LH door) fully pushed down (Automatic operation)
    Below 1 V
    M2-4 (AUTO) - M2-1 (GND)
    B - W-B
    Power window motor AUTO DOWN input
    Ignition switch ON, rear LH door power window fully open
    11 to 14 V
    M2-5 (LED) - M2-1 (GND)
    LG - W-B
    LED illumination signal
    Ignition switch ON
    11 to 14 V
    M2-5 (LED) - M2-1 (GND)
    LG - W-B
    LED illumination signal
    Approximately 43 seconds after ignition switch turned off
    Below 1 V
    M2-7 (DOWN) - M2-1 (GND)
    R - W-B
    Power window motor DOWN input
    Ignition switch ON, rear power window regulator switch assembly (for LH door) not pushed or pulled
    11 to 14 V
    M2-7 (DOWN) - M2-1 (GND)
    R - W-B
    Power window motor DOWN input
    Ignition switch ON, rear LH door power window moving, rear power window regulator switch assembly (for LH door) pushed halfway down (Manual operation)
    Below 1 V
    M2-7 (DOWN) - M2-1 (GND)
    R - W-B
    Power window motor DOWN input
    Ignition switch ON, rear LH door power window fully closed
    11 to 14 V
    M2-7 (DOWN) - M2-1 (GND)
    R - W-B
    Power window motor DOWN input
    Ignition switch ON, rear LH door power window moving, rear power window regulator switch assembly (for LH door) fully pushed down (Automatic operation)
    Below 1 V
    M2-7 (DOWN) - M2-1 (GND)
    R - W-B
    Power window motor DOWN input
    Ignition switch ON, rear LH door power window fully open
    11 to 14 V
    M2-10 (UP) - M2-1 (GND)
    G - W-B
    Power window motor UP input
    Ignition switch ON, rear power window regulator switch assembly (for LH door) not pushed or pulled
    11 to 14 V
    M2-10 (UP) - M2-1 (GND)
    G - W-B
    Power window motor UP input
    Ignition switch ON, rear LH door power window moving, rear power window regulator switch assembly (for LH door) pulled halfway up (Manual operation)
    Below 1 V
    M2-10 (UP) - M2-1 (GND)
    G - W-B
    Power window motor UP input
    Ignition switch ON, rear LH door power window fully open
    11 to 14 V
    M2-10 (UP) - M2-1 (GND)
    G - W-B
    Power window motor UP input
    Ignition switch ON, rear LH door power window moving, rear power window regulator switch assembly (for LH door) fully pulled up (Automatic operation)
    Below 1 V
    M2-10 (UP) - M2-1 (GND)
    G - W-B
    Power window motor UP input
    Ignition switch ON, rear LH door power window fully closed
    11 to 14 V
    If the result is not as specified, the power window regulator motor assembly (for rear LH door) may have a malfunction.


CHECK POWER WINDOW REGULATOR MOTOR ASSEMBLY (for Rear RH Door)


  1. Disconnect the L2 power window regulator motor assembly (for rear RH door) connector.


    B203471E91

  2. Measure the voltage and resistance according to the value(s) in the table below.

    HINT:
    Measure the values on the wire harness door with the connector disconnected.


    Tester Connection
    Wiring Color
    Terminal Description
    Condition
    Specified Condition
    L2-1 (GND) - Body ground
    W-B - Body ground
    Ground
    Always
    Below 1 Ω
    L2-2 (B) - Body ground
    G - Body ground
    Power supply
    Always
    11 to 14 V
    If the result is not as specified, there may be a malfunction in the wire harness.

  3. Reconnect the L2 power window regulator motor assembly (for rear RH door) connector.

  4. Measure the voltage according to the value(s) in the table below.

    Tester Connection
    Wiring Color
    Terminal Description
    Condition
    Specified Condition
    L2-4 (AUTO) - L2-1 (GND)
    B - W-B
    Power window motor AUTO UP input
    Ignition switch ON, rear RH door power window fully open
    11 to 14 V
    L2-4 (AUTO) - L2-1 (GND)
    B - W-B
    Power window motor AUTO UP input
    Ignition switch ON, rear RH door power window moving, rear power window regulator switch assembly (for RH door) fully pulled up (Automatic operation)
    Below 1 V
    L2-4 (AUTO) - L2-1 (GND)
    B - W-B
    Power window motor AUTO UP input
    Ignition switch ON, rear RH door power window fully closed
    11 to 14 V
    L2-4 (AUTO) - L2-1 (GND)
    B - W-B
    Power window motor AUTO DOWN input
    Ignition switch ON, rear RH door power window fully closed
    11 to 14 V
    L2-4 (AUTO) - L2-1 (GND)
    B - W-B
    Power window motor AUTO DOWN input
    Ignition switch ON, rear RH door power window moving, rear power window regulator switch assembly (for RH door) fully pushed down (Automatic operation)
    Below 1 V
    L2-4 (AUTO) - L2-1 (GND)
    B - W-B
    Power window motor AUTO DOWN input
    Ignition switch ON, rear RH door power window fully open
    11 to 14 V
    L2-5 (LED) - L2-1 (GND)
    LG - W-B
    LED illumination signal
    Ignition switch ON
    11 to 14 V
    L2-5 (LED) - L2-1 (GND)
    LG - W-B
    LED illumination signal
    Approximately 43 seconds after ignition switch turned off
    Below 1 V
    L2-7 (DOWN) - L2-1 (GND)
    R - W-B
    Power window motor DOWN input
    Ignition switch ON, rear power window regulator switch assembly (for RH door) not pushed or pulled
    11 to 14 V
    L2-7 (DOWN) - L2-1 (GND)
    R - W-B
    Power window motor DOWN input
    Ignition switch ON, rear RH door power window moving, rear power window regulator switch assembly (for RH door) pushed halfway down (Manual operation)
    Below 1 V
    L2-7 (DOWN) - L2-1 (GND)
    R - W-B
    Power window motor DOWN input
    Ignition switch ON, rear RH door power window fully closed
    11 to 14 V
    L2-7 (DOWN) - L2-1 (GND)
    R - W-B
    Power window motor DOWN input
    Ignition switch ON, rear RH door power window moving, rear power window regulator switch assembly (for RH door) fully pushed down (Automatic operation)
    Below 1 V
    L2-7 (DOWN) - L2-1 (GND)
    R - W-B
    Power window motor DOWN input
    Ignition switch ON, rear RH door power window fully open
    11 to 14 V
    L2-10 (UP) - L2-1 (GND)
    G - W-B
    Power window motor UP input
    Ignition switch ON, rear power window regulator switch assembly (for RH door) not pushed or pulled
    11 to 14 V
    L2-10 (UP) - L2-1 (GND)
    G - W-B
    Power window motor UP input
    Ignition switch ON, rear RH door power window moving, rear power window regulator switch assembly (for RH door) pulled halfway up (Manual operation)
    Below 1 V
    L2-10 (UP) - L2-1 (GND)
    G - W-B
    Power window motor UP input
    Ignition switch ON, rear RH door power window fully open
    11 to 14 V
    L2-10 (UP) - L2-1 (GND)
    G - W-B
    Power window motor UP input
    Ignition switch ON, rear RH door power window moving, rear power window regulator switch assembly (for RH door) fully pulled up (Automatic operation)
    Below 1 V
    L2-10 (UP) - L2-1 (GND)
    G - W-B
    Power window motor UP input
    Ignition switch ON, rear RH door power window fully closed
    11 to 14 V
    If the result is not as specified, the power window regulator motor assembly (for rear RH door) may have a malfunction.


CHECK INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY AND MAIN BODY ECU (MULTIPLEX NETWORK BODY ECU)


  1. Disconnect the MB and I12 main body ECU (multiplex network body ECU) connector.


    B282096E18


    Text in Illustration 
    *A
    for LHD
    *B
    for RHD

  2. Measure the voltage and resistance according to the value(s) in the table below.

    HINT:
    Measure the values on the wire harness door with the connectors disconnected.


    Tester Connection
    Wiring Color
    Terminal Description
    Condition
    Specified Condition
    MB-11 (GND1) - Body ground
    -
    Ground
    Always
    Below 1 Ω
    MB-30 (BECU) - Body ground
    -
    Battery power supply
    Always
    11 to 14 V
    I12-3 (GND2) - Body ground
    W-B - Body ground
    Ground
    Always
    Below 1 Ω
    MB-29 (ACC) - Body ground
    -
    ACC power supply
    Ignition switch ACC
    11 to 14 V
    MB-29 (ACC) - Body ground
    -
    ACC power supply
    Ignition switch off
    Below 1 V
    MB-31 (ALTB) - Body ground
    -
    Battery power supply
    Ignition switch off
    11 to 14 V
    MB-32 (IG) - Body ground
    -
    IG power supply
    Ignition switch ON
    11 to 14 V
    MB-32 (IG) - Body ground
    -
    IG power supply
    Ignition switch off
    Below 1 V
    If the result is not as specified, there may be a malfunction in the wire harness.

  3. Reconnect the MB and I12 main body ECU (multiplex network body ECU) connector.

  4. Measure the voltage according to the value(s) in the table below.

    Tester Connection
    Wiring Color
    Terminal Description
    Condition
    Specified Condition
    3C-15 (FLCY) - Body ground
    L - Body ground
    Front door courtesy switch LH input
    Front door LH open
    Below 1 V
    3C-15 (FLCY) - Body ground
    L - Body ground
    Front door courtesy switch LH input
    Front door LH closed
    11 to 14 V
    I13-19 (FRCY) - Body ground
    Y - Body ground
    Front door courtesy switch RH input
    Front door RH open
    Below 1 V
    I13-19 (FRCY) - Body ground
    Y - Body ground
    Front door courtesy switch RH input
    Front door RH closed
    11 to 14 V
    I13-11 (L2) - Body ground
    R - Body ground
    Driver door key-linked lock input
    Driver door key cylinder turned to lock
    Below 1 V
    I13-11 (L2) - Body ground
    R - Body ground
    Driver door key-linked lock input
    Driver door key cylinder off
    Pulse generation
    I13-24 (UL3) - Body ground
    GR*1 - Body ground
    Y*2 - Body ground
    Driver door key-linked unlock input
    Driver door key cylinder turned to unlock
    Below 1 V
    I13-24 (UL3) - Body ground
    GR*1 - Body ground
    Y*2 - Body ground
    Driver door key-linked unlock input
    Driver door key cylinder off
    Pulse generation
    I13-4 (PRG) - Body ground*3
    P - Body ground
    Signal output to door control receiver
    Key inserted in ignition key cylinder → Key pulled out of ignition key cylinder
    11 to 14 V → Pulse generation → 11 to 14 V
    I13-16 (RDA) - Body ground*3
    L - Body ground
    Signal input from door control receiver
    Ignition switch off, all doors closed and transmitter switch not pressed
    11 to 14 V
    Ignition switch off, all doors closed and transmitter switch pressed
    Pulse generation

    1. *1: for LHD
    2. *2: for RHD
    3. *3: w/o Smart Entry and Start System
    If the result is not as specified, the main body ECU (multiplex network body ECU) or instrument panel junction block assembly may have a malfunction.


CHECK CERTIFICATION ECU (SMART KEY ECU ASSEMBLY) (w/ Smart Entry and Start System)


  1. Disconnect the A43 certification ECU (smart key ECU assembly) connector.


    B264892E19

  2. Measure the voltage and resistance according to the value(s) in the table below.

    HINT:
    Measure the values on the wire harness door with the connector disconnected.


    Tester Connection
    Wiring Color
    Terminal Description
    Condition
    Specified Condition
    A43-2 (+B) - Body ground
    W - Body ground
    +B power supply
    Always
    11 to 14 V
    A43-11 (E) - Body ground
    W - Body ground
    Ground
    Always
    Below 1 Ω
    If the result is not as specified, there may be a malfunction in the wire harness.

  3. Reconnect the A43 certification ECU (smart key ECU assembly) connector.

  4. Measure the voltage and check for pulses according to the value(s) in the table below.

    Tester Connection
    Wiring Color
    Terminal Description
    Condition
    Specified Condition
    I78-5 (IG) - Body ground
    LG - Body ground
    IG power supply
    Ignition switch off
    Below 1 V
    I78-5 (IG) - Body ground
    LG - Body ground
    IG power supply
    Ignition switch ON
    11 to 14 V
    O1-5 (RCO) - A43-11 (E)
    G - W
    Door control receiver power source
    1. Ignition switch off
    2. Transmitter switch not pressed
    Below 1 V
    O1-5 (RCO) - A43-11 (E)
    G - W
    Door control receiver power source
    1. Ignition switch off
    2. Lock or unlock transmitter switch pressed
    4.5 to 5.5 V
    O1-17 (RDAM) - A43-11 (E)
    Y - W
    Door control receiver data input signal
    Ignition switch off
    Pulse between 11 to 14 V occurs regularly
    If the result is not as specified, the certification ECU (smart key ECU assembly) may have a malfunction.