Home › Vehicle Interior › SEAT BELT › SEAT BELT WARNING SYSTEM

SEAT BELT WARNING SYSTEM > Driver Side Seat Belt Warning Light does not Operate

for Preparation Click here


DESCRIPTION

The combination meter assembly blinks or turns off the seat belt warning light on the combination meter assembly in accordance with the state of the front seat inner belt assembly (for driver).

WIRING DIAGRAM


B281804E01


INSPECTION PROCEDURE

NOTICE:
The seat belt warning system uses the CAN communication system. First, confirm that there is no malfunction in the communication system by checking communication function of the CAN communication system. Refer to the How to Proceed with Troubleshooting procedure (Click here).

1.READ VALUE USING INTELLIGENT TESTER
  1. Connect the intelligent tester to the DLC3.

  1. Turn the ignition switch to ON.

  1. Turn the intelligent tester on.

  1. Enter the following menus: Body / Main Body / Data List.

  1. Read the Data List according to the display on the intelligent tester.

    Main Body (Main Body ECU (Multiplex Network Body ECU)) 
    Tester Display
    Measurement Item/Range
    Normal Condition
    Diagnostic Note
    D Seat Buckle SW
    Driver seat belt buckle switch/ON or OFF
    ON: Driver seat belt unfastened
    OFF: Driver seat belt fastened
    -

    OK:
    ON or OFF appears on the tester screen according to the driver seat belt condition.



NG
Go to step 3
OK


2.PERFORM ACTIVE TEST USING INTELLIGENT TESTER
  1. Connect the intelligent tester to the DLC3.

  1. Turn the ignition switch to ON.

  1. Turn the intelligent tester on.

  1. Enter the following menus: Body / Combination Meter /Active Test.

  1. Perform the Active Test according to the display on the intelligent tester.

    Combination Meter (Combination Meter Assembly) 
    Tester Display
    Test Part
    Control Range
    Diagnostic Note
    Driver Side Seat Belt
    Seat belt warning light
    OFF/ON
    -

    OK:
    The seat belt warning light on the combination meter assembly operates normally.



NG
REPLACE COMBINATION METER ASSEMBLY (Click here)
OK

REPLACE MAIN BODY ECU (MULTIPLEX NETWORK BODY ECU) (Click here)  

3.INSPECT FRONT SEAT INNER BELT ASSEMBLY (FOR DRIVER)


    B271232E04
  1. Remove the front seat inner belt assembly (for driver) (Click here).

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    2 - 3
    Driver seat belt unfastened
    Below 1 Ω
    2 - 3
    Driver seat belt fastened
    10 kΩ or higher

    Text in Illustration 
    *a
    Component without harness connected
    (Front Seat Inner Belt Assembly (for Driver))



NG
REPLACE FRONT SEAT INNER BELT ASSEMBLY (FOR DRIVER) (Click here)
OK


4.INSPECT INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY


  1. Remove the main body ECU (multiplex network body ECU) (Click here).


    B281844E01


    Text in Illustration 
    *A
    for LHD
    *B
    for RHD
    *a
    Component without harness connected
    (Instrument Panel Junction Block Assembly)
    -
    -

  1. Disconnect the 3C instrument panel junction block assembly. (for LHD)

  1. Disconnect the 3A instrument panel junction block assembly. (for RHD)

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    for LHD 
    Tester Connection
    Condition
    Specified Condition
    MB-18 (DBKL) - 3C-35
    Always
    Below 1 Ω
    for RHD 
    Tester Connection
    Condition
    Specified Condition
    MB-18 (DBKL) - 3A-38
    Always
    Below 1 Ω



NG
REPLACE INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY (Click here)
OK


5.CHECK HARNESS AND CONNECTOR (MAIN BODY ECU - FRONT SEAT INNER BELT ASSEMBLY - BODY GROUND)
  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    for LHD 
    Tester Connection
    Condition
    Specified Condition
    3C-35 - N2-3
    Always
    Below 1 Ω
    N2-3 - Body ground
    Always
    10 kΩ or higher
    N2-2 - Body ground
    Always
    Below 1 Ω
    for RHD 
    Tester Connection
    Condition
    Specified Condition
    3A-38 - O3-3
    Always
    Below 1 Ω
    O3-3 - Body ground
    Always
    10 kΩ or higher
    O3-2 - Body ground
    Always
    Below 1 Ω



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK

REPLACE MAIN BODY ECU (MULTIPLEX NETWORK BODY ECU) (Click here)