THROTTLE BODY > INSTALLATION |
| 1. INSTALL THROTTLE WITH MOTOR BODY ASSEMBLY |
![]() |
Install a new gasket to the intake air surge tank assembly.
Install the throttle with motor body assembly and wire harness clamp stay to the intake air surge tank assembly with the 4 bolts.
Connect the throttle body connector and wire harness clamp.
Connect the 2 water by-pass hoses to the throttle with motor body assembly.
| 2. INSTALL AIR CLEANER CAP SUB-ASSEMBLY |
Connect the air cleaner cap sub-assembly to the throttle with motor body assembly with the hose clamp.
Install the air cleaner cap with hose to the air cleaner case with the 2 clamps.
Connect the wire harness clamp and mass air flow meter connector.
Connect the 3 hoses.
Connect the ventilation hose.
Connect the mass air flow meter connector and wire harness clamp.
| 3. ADD ENGINE COOLANT |
Tighten the radiator drain cock plug by hand.
Close the 2 cylinder block drain cock plugs.
Loosen the air drain cock plug on the water inlet housing.
Add TOYOTA Super Long Life Coolant (SLLC) to the radiator inlet opening until coolant overflows from the air drain cock hole. Then tighten the air drain cock plug to the water inlet housing.
![]() |
Slowly fill the radiator with TOYOTA Super Long Life Coolant (SLLC).
| *a | Code Mark |
| Code Mark "K" | 8.8 liters (9.3 US qts, 7.7 lmp. qts) |
| Code Mark "J" | 8.9 liters (9.4 US qts, 7.8 lmp. qts) |
Slowly pour coolant into the radiator reserve tank assembly until it reaches the full line.
Squeeze the No. 1 and No. 2 radiator hoses several times by hand, and then check the level of the coolant.
If the coolant level is low, add coolant.
Install the radiator cap sub-assembly and reserve tank cap.
Bleed air from the cooling system.
Warm up the engine until the thermostat opens. While the thermostat is open, circulate the coolant for several minutes.
Maintain the engine speed at 2500 to 3000 rpm.
Squeeze the No. 1 and No. 2 radiator hoses several times by hand to bleed air.
Stop the engine, and wait until the engine coolant cools down.
Add engine coolant to the full line on the radiator reserve tank assembly.
| 4. INSPECT FOR COOLANT LEAK |
![]() |
Fill the radiator with coolant and attach a radiator cap tester.
Warm up the engine.
Using a radiator cap tester, increase the pressure inside the radiator to 118 kPa (1.2 kgf*cm, 17 psi), and check that the pressure does not drop.
If the pressure drops, check the hoses, radiator and water pump for leaks. If no external leaks are found, check the heater core, cylinder block and cylinder head.
| 5. INSTALL V-BANK COVER SUB-ASSEMBLY |
Fit the 3 retainers and install the V-bank cover sub-assembly.
| 6. INSTALL ENGINE UNDER COVER RH |
| 7. INSTALL FRONT WHEEL OPENING EXTENSION PAD RH |
| 8. INSTALL ENGINE UNDER COVER LH |
| 9. INSTALL FRONT WHEEL OPENING EXTENSION PAD LH |
| 10. PERFORM INITIALIZATION |
Turn the engine switch on (IG) without operating the accelerator pedal.
Connect the intelligent tester to the DLC3 and clear the DTCs (Click here).
Perform the "Inspection After Repair" (Click here).
Start the engine and check that the MIL is not illuminated. After the engine is warmed up, check that the idle speed is within the specified range when the A/C is switched off.
| Condition | Engine Idle Speed |
| A/C switched off | 600 to 700 rpm |
Enter the following menus: Powertrain / Engine and ECT / Data List / All Data / Throttle Sensor Position. Fully depress the accelerator pedal and check that the value is 60% or more.
Perform a road test and confirm that there are no abnormalities.