THROTTLE BODY > INSTALLATION |
| 1. INSTALL THROTTLE WITH MOTOR BODY ASSEMBLY |
![]() |
Install a new gasket to the intake manifold.
| *a | Groove |
| *b | Protrusion |
Temporarily install the throttle with motor body assembly and fuel tube bracket with the 4 bolts.
Connect the 2 water by-pass hoses.
Connect the purge line hose.
![]() |
Install the fuel tube bracket and the throttle with motor body assembly with the 4 bolts.
Connect the throttle with motor body assembly connector to the throttle with motor body assembly.
Connect the wire harness clamp to the fuel tube bracket.
Install the fuel tube to the fuel tube bracket.
| 2. INSTALL AIR CLEANER CAP SUB-ASSEMBLY |
Install the air cleaner filter element to the air cleaner case sub-assembly.
![]() |
Connect the air cleaner cap sub-assembly to the throttle with motor body assembly and release the lock of the air cleaner hose clamp.
| *1 | Air Cleaner Hose Clamp |
Connect the ventilation hose to the cylinder head cover.
Install the air cleaner cap sub-assembly and tighten the 2 bolts.
Connect the wire harness clamp.
Connect the mass air flow meter connector.
Connect the purge line hose to the 2 clamps.
Connect the 2 vacuum switching valve vacuum hoses.
Connect the vacuum switching valve connector.
| 3. ADD ENGINE COOLANT |
Tighten the radiator drain cock plug by hand.
Tighten the cylinder block drain cock plug.
Slowly fill the radiator with TOYOTA Super Long Life Coolant (SLLC).
Slowly pour engine coolant into the radiator reserve tank assembly until it reaches the full line.
Squeeze the No. 1 and No. 2 radiator hoses several times by hand, and then check the level of the engine coolant.
If the engine coolant level is low, add engine coolant.
Install the radiator cap sub-assembly and reserve tank cap.
Bleed air from the cooling system.
Warm up the engine until the thermostat opens. While the thermostat is open, circulate the engine coolant for several minutes.
Maintain the engine speed at 2000 to 2500 rpm.
Squeeze the No. 1 and No. 2 radiator hoses several times by hand to bleed air.
Stop the engine and wait until the engine coolant cools down.
Add engine coolant to the full line on the radiator reserve tank assembly.
| 4. INSPECT FOR COOLANT LEAK |
![]() |
Fill the radiator assembly with engine coolant and attach a radiator cap tester.
Warm up the engine.
Using a radiator cap tester, increase the pressure inside the radiator assembly to 118 kPa (1.2 kgf/cm2, 17 psi), and check that the pressure does not drop.
If the pressure drops, check the hoses, radiator assembly and engine water pump assembly for leaks. If no external leaks are found, check the heater core, cylinder block and cylinder head.
| 5. INSTALL FRONT OUTER COWL TOP PANEL SUB-ASSEMBLY |
Install the front outer cowl top panel sub-assembly with the 10 bolts.
Engage the 2 clamps to install the wire harness to the front outer cowl top panel sub-assembly.
| 6. INSTALL WINDSHIELD WIPER MOTOR AND LINK ASSEMBLY |
| 7. INSTALL NO. 1 ENGINE COVER SUB-ASSEMBLY |
Install the No. 1 engine cover sub-assembly with the 2 nuts.
| 8. PERFORM INITIALIZATION |
Turn the ignition switch to ON without operating the accelerator pedal sensor assembly.
Connect the intelligent tester to the DLC3 and clear the DTCs (Click here).
Start the engine and check that the MIL is not illuminated. After the engine is warmed up, check that the idle speed is within the specified range with the A/C switch off.
| Condition | Engine Idle Speed |
| A/C switch off | 610 to 710 rpm |
Enter the following menus: Powertrain / Engine and ECT / Data List / Gas Throttle / Throttle Sensor Position. Fully depress the accelerator pedal and check that the value is 60% or more.
Perform a road test and confirm that there are no abnormalities.