Home › Audio / Visual / Telematics › NAVIGATION / MULTI INFO DISPLAY › NAVIGATION SYSTEM

DTC    B15DA    Rear Console Recognition Disconnected

for Preparation Click here


DESCRIPTION

The stereo component amplifier assembly and cooler control switch assembly are connected by the AVC-LAN communication line.
The navigation ECU sub-assembly is also connected to the stereo component amplifier assembly by the AVC-LAN communication line.
When an AVC-LAN communication error occurs between the stereo component amplifier assembly and cooler control switch assembly, this DTC will be stored.

HINT:
If B15DA and B15D3 are output, troubleshoot for B15D3 first.


DTC No.
DTC Detection Condition
Trouble Area
B15DA*1
When either condition below is met:
  1. Cooler control switch assembly is/was not connected while the ignition switch is/was ON or ACC.
  2. Communication between the master unit and the cooler control switch assembly is/was not possible when the engine is started.
  1. Cooler control switch assembly power source circuit
  2. AVC-LAN circuit between navigation ECU sub-assembly and cooler control switch assembly
  3. Cooler control switch assembly
  4. Stereo component amplifier assembly
  5. Navigation ECU sub-assembly
  6. Harness or connector

HINT:
  1. *1: Even if no fault is present, this DTC may be stored depending on the battery condition or engine start voltage.
  2. The navigation ECU sub-assembly is the master unit.


WIRING DIAGRAM


E229568E01


INSPECTION PROCEDURE

NOTICE:
Inspect the fuses for circuits related to this system before performing the following inspection procedure.

1.CHECK DTC
  1. Clear the DTCs (Click here).

  1. Recheck for DTCs and check if the same DTC is output again.

    Result:
    Result
    Proceed to
    B15DA is output.
    A
    B15DA and B15D3 are output.
    B
    No DTCs are output.
    C

    HINT:
    If B15DA and B15D3 are output, troubleshoot for B15D3 first.



B
GO TO DTC "B15D3" IN DIAGNOSTIC TROUBLE CODE CHART (Click here)

C
END
A


2.CHECK OPTIONAL COMPONENTS (INCLUDING ASSOCIATED WIRING)
  1. Check for optional components

    1. Check that optional components (including associated wiring) which generate radio waves are not installed.

      Result:
      Result
      Proceed to
      Optional components (including associated wiring) are installed.
      A
      Optional components (including associated wiring) are not installed.
      B

HINT:
  1. Electrical noise from radio waves generated by optional components or the wiring for those components may affect AVC-LAN communication.
  2. This DTC may be stored when an AVC-LAN communication error occurs due to electrical noise.



B
Go to step 4
A


3.REMOVE OPTIONAL COMPONENTS (INCLUDING ASSOCIATED WIRING)
  1. Remove optional components (including associated wiring).

    NOTICE:
    Do not remove optional components or associated wiring without the permission of the customer.


NEXT


4.CHECK DTC
  1. Clear the DTCs (Click here).

  1. Recheck for DTCs and check if the same DTC is output again.

    OK:
    No DTCs are output.



NG
Go to step 5
OK

END 

5.CHECK HARNESS AND CONNECTOR (COOLER CONTROL SWITCH ASSEMBLY POWER SOURCE)
  1. Disconnect the cooler control switch assembly connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    X1-16 (GND) - Body ground
    Always
    Below 1 Ω

  1. Measure the voltage according to the value(s) in the table below.

    Standard Voltage:
    Tester Connection
    Condition
    Specified Condition
    X1-1 (+B) - X1-16 (GND)
    Always
    11 to 14 V
    X1-7 (IG+) - X1-16 (GND)
    Ignition switch ON
    11 to 14 V
    X1-6 (ACC) - X1-16 (GND)
    Ignition switch ACC
    11 to 14 V



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK


6.CHECK HARNESS AND CONNECTOR (STEREO COMPONENT AMPLIFIER ASSEMBLY - COOLER CONTROL SWITCH ASSEMBLY)
  1. Disconnect the stereo component amplifier assembly connector.

  1. Disconnect the cooler control switch assembly connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    I69-20 (TXD+) - X1-15 (TX+)
    Always
    Below 1 Ω
    I69-19 (TXD-) - X1-5 (TX-)
    Always
    Below 1 Ω
    I69-20 (TXD+) - Body ground
    Always
    10 kΩ or higher
    I69-19 (TXD-) - Body ground
    Always
    10 kΩ or higher



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK


7.REPLACE COOLER CONTROL SWITCH ASSEMBLY
  1. Replace the cooler control switch assembly (Click here).

  1. Clear the DTCs (Click here).

  1. Recheck for DTCs and check if the same DTC is output again.

    OK:
    No DTCs are output.



NG
Go to step 8
OK

END 

8.REPLACE STEREO COMPONENT AMPLIFIER ASSEMBLY
  1. Replace the stereo component amplifier assembly (Click here).

  1. Clear the DTCs (Click here).

  1. Recheck for DTCs and check if the same DTC is output again.

    OK:
    No DTCs are output.



NG
REPLACE NAVIGATION ECU SUB-ASSEMBLY (Click here)
OK

END