Home › General › SPECIFICATIONS › 2AR-FE ENGINE CONTROL

2AR-FE ENGINE CONTROL > SERVICE DATA



Camshaft timing oil control valve assembly
Standard Resistance
20°C (68°F)
6.9 to 7.9 Ω
Throttle with motor body assembly
Standard Resistance
1 (M-) - 2 (M+)
0.3 to 100 Ω at 20°C (68°F)
Accelerator pedal sensor assembly
Standard Voltage (Accel Sensor Out No.1)
Fully Released
0.5 to 1.1 V
Fully Depressed
2.6 to 4.5 V
Standard Voltage (Accel Accel Sensor Out No.2)
Fully Released
1.2 to 2.0 V
Fully Depressed
3.4 to 4.98 V
Mass air flow meter
Standard Resistance
1 (THA) - 2 (E2)
13.6 to 18.4 kΩ at -20°C (-4°F)
1 (THA) - 2 (E2)
2.21 to 2.69 kΩ at 20°C (68°F)
1 (THA) - 2 (E2)
0.49 to 0.67 kΩ at 60°C (140°F)
Spark plug
Standard Insulation Resistance
10 MΩor more
Recommended spark plug
SK16HR11 DENSO made
Maximum electrode gap
1.3 mm (0.0512 in.)
for used spark plug
Electrode gap
1.0 to 1.1mm (0.0394 to 0.0433 in.)
for new spark plug
Crankshaft position sensor
Standard Resistance
Cold
1630 to 2740 Ω
Hot
2065 to 3225 Ω
Engine coolant temperature sensor
Standard Resistance
20°C (68°F)
2.32 to 2.59 kΩ
80°C (176°F)
0.310 to 0.326 kΩ
Knock control sensor
Standard Resistance
at 20°C (68°F)
120 to 280 kΩ
Air fuel ratio sensor
Standard Resistance
1 (HA1A) - 2 (+B)
1.6 to 3.2 Ω at 20°C (68°F)
1 (HA1A) - 4 (A1A-)
10 kΩ or higher
Oxygen sensor
Standard Resistance
1 (HT1B) - 2 (+B)
11 to 16 Ω at 20°C (68°F)
1 (HT1B) - 4 (E2)
10 kΩ or higher
EFI MAIN relay
Standard Resistance
No. 1 integration relay 1B-1 - No. 1 integration relay 1A-8
10 kΩ or higher
No. 1 integration relay 1B-1 - No. 1 integration relay 1A-8
Below 1 Ω (Battery voltage is applied between terminals 1C-7 and 1E-2)
No. 1 integration relay 1B-1 - No. 1 integration relay 1C-3
No. 1 integration relay 1B-1 - No. 1 integration relay 1C-4
No. 1 integration relay 1B-1 - No. 1 integration relay 1C-9
No. 1 integration relay 1B-1 - No. 1 integration relay 1C-10
EFI MAIN2 relay
Standard Resistance
No. 1 integration relay 1A-6 - No. 1 integration relay 1D-1
10 kΩ or higher
No. 1 integration relay 1A-6 - No. 1 integration relay 1D-1
Below 1 Ω (Battery voltage is applied between terminals 1A-8 and 1E-2)
No. 1 integration relay 1A-7 - No. 1 integration relay 1D-1
IG2 relay
Standard Resistance
No. 1 integration relay 1A-1 - No. 1 integration relay 1D-3
10 kΩ or higher
No. 1 integration relay 1A-1 - No. 1 integration relay 1D-3
Below 1 Ω (Battery voltage is applied between terminals 1C-8 and 1E-2)
No. 1 integration relay 1A-3 - No. 1 integration relay 1D-3
No. 1 integration relay 1C-1 - No. 1 integration relay 1D-3
No. 1 integration relay 1C-2 - No. 1 integration relay 1D-3
No. 1 integration relay 1C-5 - No. 1 integration relay 1D-3
C/OPN relay
Standard Resistance
No. 1 integration relay 1A-6 - No. 1 integration relay 1D-1
10 kΩ or higher
No. 1 integration relay 1A-6 - No. 1 integration relay 1D-1
Below 1 Ω (Battery voltage is applied between terminals 1A-1 and 1E-1)
No. 1 integration relay 1A-7 - No. 1 integration relay 1D-1