1AZ-FE ENGINE CONTROL > SERVICE DATA |
| Camshaft timing oil control valve assembly | ||
| Standard Resistance | 20°C (68°F) | 6.9 to 7.9 Ω |
| Throttle with motor body assembly | ||
| Standard Resistance | E16-1 (M-) - E16-2 (M+) | 0.3 to 100 Ω at 20°C (68°F) |
| Accelerator pedal sensor assembly | ||
| Standard Voltage (Accel Sensor Out No.1) | Fully Released | 0.5 to 1.1 V |
| Fully Depressed | 2.6 to 4.5 V | |
| Standard Voltage (Accel Accel Sensor Out No.2) | Fully Released | 1.2 to 2.0 V |
| Fully Depressed | 3.4 to 4.98 V | |
| Mass air flow meter sub-assembly | ||
| Standard Resistance | E14-1 (THA) - E14-2 (E2) | 13.6 to 18.4 kΩ at -20°C (-4°F) |
| E14-1 (THA) - E14-2 (E2) | 2.21 to 2.69 kΩ at 20°C (68°F) | |
| E14-1 (THA) - E14-2 (E2) | 0.49 to 0.67 kΩ at 60°C (140°F) | |
| Spark plug | ||
| Standard Insulation Resistance | 10 MΩor more | |
| Recommended spark plug | SK16HR11 DENSO made | |
| IFR5A11 NGK made | ||
| Maximum electrode gap | 1.3 mm (0.0512 in.) for used spark plug | |
| Electrode gap | 1.0 to 1.1mm (0.0394 to 0.0433 in.) for new spark plug | |
| Camshaft position sensor | ||
| Standard Resistance | Cold | 835 to 1400 Ω |
| Hot | 1060 to 1645 Ω | |
| Crankshaft position sensor | ||
| Standard Resistance | Cold | 985 to 1600 Ω |
| Hot | 1265 to 1890 Ω | |
| Engine coolant temperature sensor | ||
| Standard Resistance | 20°C (68°F) | 2.32 to 2.59 kΩ |
| 80°C (176°F) | 0.310 to 0.326 kΩ | |
| Knock control sensor | ||
| Resistance | at 20°C (68°F) | 120 to 280 kΩ |
| Air fuel ratio sensor | ||
| Standard Resistance | E19-1 (HA1A) - E19-2 (+B) | 1.8 to 3.4 Ω at 20°C (68°F) |
| E19-1 (HA1A) - E19-4 (A1A-) | 10 kΩ or higher | |
| Oxygen sensor | ||
| Standard Resistance | E21-1 (HT1B) - E21-2 (+B) | 9 to 14 Ω at 20°C (68°F) |
| E21-1 (HT1B) - E21-4 (E2) | 10 kΩ or higher | |
| EFI MAIN relay | ||
| Specified condition | No. 1 integration relay 1B-1 - No. 1 integration relay 1A-8 | 10 kΩ or higher |
| No. 1 integration relay 1B-1 - No. 1 integration relay 1A-8 | Below 1 Ω (Battery voltage is applied between terminals 1C-7 and 1E-2) | |
| No. 1 integration relay 1B-1 - No. 1 integration relay 1C-3 | ||
| No. 1 integration relay 1B-1 - No. 1 integration relay 1C-4 | ||
| No. 1 integration relay 1B-1 - No. 1 integration relay 1C-9 | ||
| No. 1 integration relay 1B-1 - No. 1 integration relay 1C-10 | ||
| IG2 relay | ||
| Standard Resistance | No. 1 integration relay 1A-1 - No. 1 integration relay 1D-3 | 10 kΩ or higher |
| No. 1 integration relay 1A-1 - No. 1 integration relay 1D-3 | Below 1 Ω (Battery voltage is applied between terminals 1C-8 and 1E-2) | |
| No. 1 integration relay 1A-3 - No. 1 integration relay 1D-3 | ||
| No. 1 integration relay 1C-1 - No. 1 integration relay 1D-3 | ||
| No. 1 integration relay 1C-2 - No. 1 integration relay 1D-3 | ||
| No. 1 integration relay 1C-5 - No. 1 integration relay 1D-3 | ||
| C/OPN relay | ||
| Standard Resistance | No. 1 integration relay 1A-7 - No. 1 integration relay 1C-6 | 10 kΩ or higher |
| No. 1 integration relay 1A-7 - No. 1 integration relay 1C-6 | Below 1 Ω (Battery voltage is applied between terminals 1A-1 and 1E-1) | |
| No. 1 integration relay 1A-6 - No. 1 integration relay 1C-6 | ||