Home › Engine / Hybrid System · 2AR-FE › ENGINE CONTROL › SFI SYSTEM

SFI SYSTEM > ECM Power Source Circuit

for Preparation Click here


DESCRIPTION

When the ignition switch is turned to ON, battery voltage is applied to the IGSW terminal of the ECM. The output signal from the MREL terminal of the ECM causes current to flow to the coil of the No. 1 integration relay (EFI MAIN relay), closing the contacts and supplying power to terminals +B and +B2 of the ECM.

WIRING DIAGRAM


A266855E02


INSPECTION PROCEDURE

NOTICE:
Inspect the fuses for circuits related to this system before performing the following inspection procedure.

1.CHECK HARNESS AND CONNECTOR (NO. 1 INTEGRATION RELAY VOLTAGE)
  1. Remove the No. 1 integration relay from the engine room relay block and junction block assembly.

  1. Turn the ignition switch to ON.

  1. Measure the voltage according to the value(s) in the table below.

    Standard Voltage:

    Tester Connection
    Switch Condition
    Specified Condition
    1C-8 - Body ground
    Ignition switch ON
    11 to 14 V


    Result 
    Result
    Proceed to
    OK
    A
    NG (w/o smart entry and start system)
    B
    NG (w/ smart entry and start system)
    C



B
Go to step 7

C
Go to step 9
A


2.CHECK HARNESS AND CONNECTOR (BATTERY - NO. 1 INTEGRATION RELAY)
  1. Remove the No. 1 integration relay from the engine room relay block and junction block assembly.

  1. Measure the voltage according to the value(s) in the table below.

    Standard Voltage:

    Tester Connection
    Condition
    Specified Condition
    1D-3 - Body ground
    Always
    11 to 14 V
    1B-1 - Body ground
    Always
    11 to 14 V



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK


3.INSPECT NO. 1 INTEGRATION RELAY
  1. Inspect the No. 1 integration relay (Click here).



NG
REPLACE NO. 1 INTEGRATION RELAY (Click here)
OK


4.CHECK HARNESS AND CONNECTOR (NO. 1 INTEGRATION RELAY - BODY GROUND)
  1. Remove the No. 1 integration relay from the engine room relay block and junction block assembly.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:

    Tester Connection
    Condition
    Specified Condition
    1E-2 - Body ground
    Always
    Below 1 Ω



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK


5.CHECK HARNESS AND CONNECTOR (NO. 1 INTEGRATION RELAY - ECM)
  1. Remove the No. 1 integration relay from the engine room relay block and junction block assembly.

  1. Disconnect the ECM connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:

    Tester Connection
    Condition
    Specified Condition
    1C-1 - A25-37 (IGSW)
    Always
    Below 1 Ω
    1C-9 - A25-2 (+B)
    Always
    Below 1 Ω
    1C-10 - A25-3 (+B2)
    Always
    Below 1 Ω
    1C-7 - A25-46 (MREL)
    Always
    Below 1 Ω



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK


6.CHECK HARNESS AND CONNECTOR (ECM - BODY GROUND)
  1. Disconnect the ECM connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:

    Tester Connection
    Condition
    Specified Condition
    E26-16 (E1) - Body ground
    Always
    Below 1 Ω



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK

PROCEED TO NEXT SUSPECTED AREA SHOWN IN PROBLEM SYMPTOMS TABLE (Click here)  

7.CHECK HARNESS AND CONNECTOR (BATTERY - IGNITION SWITCH ASSEMBLY)
  1. Disconnect the ignition switch assembly connector.

  1. Measure the voltage according to the value(s) in the table below.

    Standard Voltage:

    Tester Connection
    Condition
    Specified Condition
    I36-5 (AM2) - Body ground
    Always
    11 to 14 V



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK


8.INSPECT IGNITION SWITCH ASSEMBLY
  1. Inspect the ignition switch assembly (Click here).



NG
REPLACE IGNITION SWITCH ASSEMBLY (Click here)
OK

REPAIR OR REPLACE HARNESS OR CONNECTOR (NO. 1 INTEGRATION RELAY - IGNITION SWITCH ASSEMBLY) 

9.CHECK HARNESS AND CONNECTOR (CERTIFICATION ECU - NO. 1 INTEGRATION RELAY)
  1. Remove the No. 1 integration relay from the engine room relay block and junction block assembly.

  1. Disconnect the certification ECU (smart key ECU assembly) connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:

    Tester Connection
    Condition
    Specified Condition
    A43-9 (IG2D) - 1C-8
    Always
    Below 1 Ω



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK

GO TO SMART ENTRY AND START SYSTEM (Click here)