REAR SUNSHADE ASSEMBLY > REMOVAL |
| 1. PRECAUTION (w/ Rear Seat Side Airbag) |
| 2. DISCONNECT CABLE FROM NEGATIVE BATTERY TERMINAL (w/ Rear Seat Side Airbag) |
| 3. REMOVE REAR SEAT HEADREST ASSEMBLY |
| 4. REMOVE REAR SEAT CUSHION ASSEMBLY (for Fold Down Seat Type) |
![]() |
Disengage the hook of the seat cushion from the vehicle body as shown in the illustration.
| a | 100 mm (3.94 in.) or less |
Choose a hook to disengage first. Place your hands near the hook as shown in the illustration. Then lift the seat cushion to disengage the hook.
Repeat the step above for the other hook.
Remove the rear seat cushion assembly.
| 5. REMOVE REAR SEAT CUSHION LOCK HOOK (for Fold Down Seat Type) |
![]() |
Disengage the claw and remove the rear seat cushion lock hook.
| 6. REMOVE REAR SIDE SEATBACK ASSEMBLY LH (for Fold Down Seat Type) |
Disconnect the rear seat outer belt from the rear seat shoulder belt guide LH.
![]() |
Remove the bolt.
Disengage the hook and remove the rear side seatback assembly LH.
| 7. REMOVE REAR SIDE SEATBACK ASSEMBLY RH (for Fold Down Seat Type) |
Disconnect the rear seat outer belt from the rear seat shoulder belt guide RH.
![]() |
Remove the bolt.
Disengage the hook and remove the rear side seatback assembly RH.
| 8. REMOVE REAR SEATBACK ASSEMBLY LH (for Fold Down Seat Type) |
Disconnect the rear seat outer belt from the rear seat center shoulder belt guide.
Fold down the rear seatback assembly LH.
![]() |
Disengage the fastener as shown in the illustration.
| *1 | Fastener |
![]() |
Remove the 2 bolts and rear seatback assembly LH.
| 9. REMOVE REAR CENTER SEAT HEADREST ASSEMBLY (for Reclining Seat Type) |
| 10. REMOVE REAR SEAT CUSHION ASSEMBLY (for Reclining Seat Type) |
![]() |
Disengage the hook of the seat cushion from the vehicle body as shown in the illustration.
| a | 100 mm (3.94 in.) or less |
Choose a hook to detach first. Place your hands near the hook as shown in the illustration. Then lift the seat cushion to detach the hook.
Repeat the step above for the other hook.
w/ Seat Heater System:
Disconnect the 2 seat heater connectors.
Remove the rear seat cushion assembly.
| 11. REMOVE REAR SEAT CUSHION LOCK HOOK (for Reclining Seat Type) |
![]() |
Disengage the claw and remove the rear seat cushion lock hook.
| 12. REMOVE REAR SEATBACK COVER (for Reclining Seat Type) |
![]() |
Disengage the 4 claws and remove the 2 rear seatback covers.
| 13. REMOVE REAR SEATBACK ASSEMBLY LH (for Reclining Seat Type) |
w/ Rear Seat Side Airbag:
Disconnect each connector and clamp from the child restraint seat anchor bracket sub-assembly LH.
Disengage the 2 rear seat belts from the 2 rear seat shoulder belt guides.
![]() |
Disengage the 2 hooks and disconnect the cover.
Remove the 2 nuts, 2 bolts and rear seatback assembly LH.
| 14. REMOVE REAR SEATBACK ASSEMBLY RH (for Reclining Seat Type) |
w/ Rear Seat Side Airbag:
Disconnect each connector and clamp from the child restraint seat anchor bracket sub-assembly RH.
Disengage the rear seat belt from the rear seat shoulder belt guide.
![]() |
Disengage the 2 hooks and disconnect the cover.
Remove the 2 nuts, 2 bolts and rear seatback assembly RH.
| 15. REMOVE CENTER SEATBACK ASSEMBLY (for Reclining Seat Type) |
Disconnect the connector.
![]() |
Remove the 2 bolts.
Disengage the hook and remove the center seatback assembly as shown in the illustration.
| 16. REMOVE REAR DOOR SCUFF PLATE LH (for Reclining Seat Type) |
![]() |
Disengage the 6 claws and remove the rear door scuff plate LH.
| 17. REMOVE REAR DOOR SCUFF PLATE RH (for Reclining Seat Type) |
| 18. DISCONNECT REAR DOOR OPENING TRIM WEATHERSTRIP LH |
Disconnect the rear door opening trim weatherstrip LH.
| 19. DISCONNECT REAR DOOR OPENING TRIM WEATHERSTRIP RH |
Disconnect the rear door opening trim weatherstrip RH.
| 20. REMOVE REAR SEAT SIDE GARNISH LH (for Reclining Seat Type) |
![]() |
Remove the bolt.
Disengage the claw, 2 clips and guide and remove the rear seat side garnish LH.
| 21. REMOVE REAR SEAT SIDE GARNISH RH (for Reclining Seat Type) |
| 22. REMOVE ROOF SIDE INNER GARNISH LH |
![]() |
Disengage the 5 clips.
Disengage the guide and remove the roof side inner garnish LH.
| 23. REMOVE ROOF SIDE INNER GARNISH RH |
| 24. DISCONNECT REAR SEAT OUTER BELT ASSEMBLY (for LH Side) |
![]() |
Remove the bolt and disconnect the floor anchor of the rear seat outer belt assembly.
| 25. DISCONNECT REAR SEAT OUTER BELT ASSEMBLY (for RH Side) |
![]() |
Remove the bolt and disconnect the floor anchor of the rear seat outer belt assembly.
| 26. REMOVE CHILD RESTRAINT SEAT ANCHOR BRACKET SUB-ASSEMBLY LH |
![]() |
Remove the 2 nuts and child restraint seat anchor bracket sub-assembly LH.
| *A | for Fold Down Seat Type |
| *B | for Reclining Seat Type w/o Seat Heater System |
| *C | for Reclining Seat Type w/ Seat Heater System |
| 27. DISCONNECT REAR SEAT INNER WITH CENTER BELT ASSEMBLY LH |
![]() |
Remove the bolt and disconnect the floor anchor of the rear seat inner with center belt assembly LH.
| 28. REMOVE CENTER STOP LIGHT SET |
![]() |
Slide the center stop light set in the order and directions shown by the arrows in the illustration while pushing it towards the rear of the vehicle to disengage the 4 claws.
![]() |
Turn the center stop light set 180 degrees as shown by the arrow in the illustration.
Disconnect the connector and remove the center stop light set.
| 29. REMOVE REAR SEAT SHOULDER BELT COVER |
![]() |
Using a moulding remover, disengage the 2 claws and 4 guides and remove the rear seat shoulder belt cover.
| 30. REMOVE PACKAGE TRAY TRIM PANEL ASSEMBLY |
![]() |
Using pliers, disengage the 3 clips from inside the luggage compartment as shown in the illustration.
| *1 | Protective Tape |
Disengage the guide.
Pass the 3 rear seat belt floor anchors through the package tray trim panel assembly then remove the package tray trim panel assembly.
| 31. REMOVE NO. 2 PACKAGE TRAY TRIM PANEL ASSEMBLY |
![]() |
Disengage the 3 clips and 5 guides.
Pass the center stop light connector through the No. 2 package tray trim panel assembly and remove the No. 2 package tray trim panel assembly.
| 32. REMOVE REAR WINDOW SHADE ASSEMBLY |
![]() |
Disconnect the connector.
Remove the 3 bolts (A).
Loosen the bolt (B) and remove the rear window shade assembly.