Home › Vehicle Interior › THEFT DETERRENT / KEYLESS ENTRY › ENGINE IMMOBILISER SYSTEM (w/o Smart Entry and Start System)

ENGINE IMMOBILISER SYSTEM (w/o Smart Entry and Start System) > TERMINALS OF ECU

for Preparation Click here



CHECK TRANSPONDER KEY AMPLIFIER


  1. Disconnect the I34 transponder key amplifier connector.


    B203482E06

  2. Measure the resistance according to the value(s) in the table below.

    HINT:
    Measure the values on the wire harness side with the connector disconnected.


    Tester Connection
    Wiring Color
    Terminal Description
    Condition
    Specified Condition
    I34-7 (AGND) - Body ground
    V - Body ground
    Ground
    Always
    Below 1 Ω
    If the result is not as specified, there may be a malfunction on the wire harness side.

  3. Reconnect the I34 transponder key amplifier connector.

  4. Measure the voltage and check for pulses according to the value(s) in the table below.

    Tester Connection
    Wiring Color
    Terminal Description
    Condition
    Specified Condition
    I34-1 (VC5) - I34-7 (AGND)
    LG - V
    Power source
    No key in ignition key cylinder
    Below 1 V
    I34-1 (VC5) - I34-7 (AGND)
    LG - V
    Power source
    Key in ignition key cylinder
    4.6 to 5.4 V
    I34-4 (CODE) - I34-7 (AGND)
    SB - V
    Demodulated signal of key code data
    No key in ignition key cylinder
    Below 1 V
    I34-4 (CODE) - I34-7 (AGND)
    SB - V
    Demodulated signal of key code data
    Key in ignition key cylinder
    Pulse generation
    (See waveform 1)
    I34-5 (TXCT) - I34-7 (AGND)
    R - V
    Key code output signal
    No key in ignition key cylinder
    Below 1 V
    I34-5 (TXCT) - I34-7 (AGND)
    R - V
    Key code output signal
    Key in ignition key cylinder
    Pulse generation
    (See waveform 2)
    If the result is not as specified, the transponder key amplifier may have a malfunction.



  5. Inspect using an oscilloscope.

    NOTICE:
    The waveform shown in the illustration is an example for reference only. Noise, chattering, etc. are not shown.




      B255093E02
    1. Waveform 1 (Reference)
      Tester Connection
      I34-4 (CODE) - I34-7 (AGND)
      Tool Setting
      2 V/DIV., 20 ms./DIV.
      Condition
      Key in ignition key cylinder



    2. B255094E02
    3. Waveform 2 (Reference)
      Tester Connection
      I34-5 (TXCT) - I34-7 (AGND)
      Tool Setting
      2 V/DIV., 10 ms./DIV.
      Condition
      Key in ignition key cylinder


CHECK TRANSPONDER KEY ECU ASSEMBLY


  1. Disconnect the I19 transponder key ECU assembly connector.


    B255101E02

  2. Measure the resistance and voltage according to the value(s) in the table below.

    HINT:
    Measure the values on the wire harness side with the connector disconnected.


    Tester Connection
    Wiring Color
    Terminal Description
    Condition
    Specified Condition
    I19-1 (+B) - I19-16 (GND)
    W - BR
    Battery
    Always
    11 to 14 V
    I19-2 (IG) - I19-16 (GND)
    R - BR
    Ignition switch signal
    Ignition switch off
    Below 1 V
    I19-2 (IG) - I19-16 (GND)
    R - BR
    Ignition switch signal
    Ignition switch ON
    11 to 14 V
    I19-3 (KSW) - I19-16 (GND)
    G - BR
    Unlock warning switch signal
    No key in ignition key cylinder
    10 kΩ or higher
    I19-3 (KSW) - I19-16 (GND)
    G - BR
    Unlock warning switch signal
    Key in ignition key cylinder
    Below 1 Ω
    I19-16 (GND) - Body ground
    BR - Body ground
    Ground
    Always
    Below 1 Ω
    If the result is not as specified, there may be a malfunction on the wire harness side.

  3. Reconnect the I19 transponder key ECU assembly connector.

  4. Measure the resistance and voltage, and check for pulses according to the value(s) in the table below.

    Tester Connection
    Wiring Color
    Terminal Description
    Condition
    Specified Condition
    I19-3 (KSW) - I19-16 (GND)
    G - BR
    Unlock warning switch signal
    No key in ignition key cylinder
    11 to 14 V
    I19-3 (KSW) - I19-16 (GND)
    G - BR
    Unlock warning switch signal
    Key in ignition key cylinder
    Below 1 V
    I19-4 (TXCT) - I19-5 (AGND)
    R - V
    Transponder key amplifier communication signal
    No key in ignition key cylinder
    Below 1 V
    I19-4 (TXCT) - I19-5 (AGND)
    R - V
    Transponder key amplifier communication signal
    Key in ignition key cylinder
    Pulse generation
    (See waveform 1)
    I19-5 (AGND) - Body ground
    V - Body ground
    Ground
    Always
    Below 1 Ω
    I19-8 (IND) - I19-16 (GND)
    L - BR
    Security indicator signal
    No key in ignition key cylinder, or 20 sec. elapsed after turning the ignition switch to on (ACC) or off (engine immobiliser system set)
    Pulse generation
    I19-8 (IND) - I19-16 (GND)
    L - BR
    Security indicator signal
    Key in ignition key cylinder (engine immobiliser system unset)
    Below 1 V
    I19-9 (D) - I19-16 (GND)
    GR - BR
    DLC3 communication
    Without communication
    Below 1 V
    I19-9 (D) - I19-16 (GND)
    GR - BR
    DLC3 communication
    During communication
    Pulse generation
    I19-12 (EFII) - I19-16 (GND)
    R - BR
    ECM input signal
    Ignition switch off
    11 to 14 V
    I19-12 (EFII) - I19-16 (GND)
    R - BR
    ECM input signal
    Within 3 seconds after starter operates and initial combustion occurs, or within 3 seconds after ignition switch first turned to ON after battery disconnected and connected.
    Pulse generation
    (See waveform 2)
    I19-13 (EFIO) - I19-16 (GND)
    G - BR
    ECM output signal
    Ignition switch off
    Below 1 V
    I19-13 (EFIO) - I19-16 (GND)
    G - BR
    ECM output signal
    Within 3 seconds after starter operates and initial combustion occurs, or within 3 seconds after ignition switch first turned to ON after battery disconnected and connected.
    Pulse generation
    (See waveform 3)
    I19-14 (VC5) - I19-5 (AGND)
    LG - V
    Transponder key amplifier power source
    No key in ignition key cylinder
    Below 1 V
    I19-14 (VC5) - I19-5 (AGND)
    LG - V
    Transponder key amplifier power source
    Key in ignition key cylinder
    4.6 to 5.4 V
    I19-15 (CODE) - I19-5 (AGND)
    SB - V
    Transponder key amplifier communication signal
    No key in ignition key cylinder
    Below 1 V
    I19-15 (CODE) - I19-5 (AGND)
    SB - V
    Transponder key amplifier communication signal
    Key in ignition key cylinder
    Pulse generation
    (See waveform 4)
    If the result is not as specified, the transponder key ECU assembly may have a malfunction.



  5. Inspect using an oscilloscope.

    NOTICE:
    The waveform shown in the illustration is an example for reference only. Noise, chattering, etc. are not shown.




      B255094E02
    1. Waveform 1 (Reference)
      Tester Connection
      I19-4 (TXCT) - I19-5 (AGND)
      Tool Setting
      2 V/DIV., 10 ms./DIV.
      Condition
      Key in ignition key cylinder



    2. Waveform 2 (Reference)


      B278942E01


      Text in Illustration 
      *a
      Approximately 160 ms
      *b
      Approximately 270 ms
      Tester Connection
      I19-12 (EFII) - I19-16 (GND)
      Tool Setting
      2 V/DIV., 500 ms./DIV.
      Condition
      Within 3 seconds after starter operates and initial combustion occurs, or within 3 seconds after ignition switch first turned to ON after battery disconnected and connected.



    3. Waveform 3 (Reference)


      B278943E01


      Text in Illustration 
      *a
      Approximately 160 ms
      *b
      Approximately 270 ms
      Tester Connection
      I19-13 (EFIO) - I19-16 (GND)
      Tool Setting
      2 V/DIV., 500 ms./DIV.
      Condition
      Within 3 seconds after starter operates and initial combustion occurs, or within 3 seconds after ignition switch first turned to ON after battery disconnected and connected.



    4. B255093E02
    5. Waveform 4 (Reference)
      Tester Connection
      I19-15 (CODE) - I19-5 (AGND)
      Tool Setting
      2 V/DIV., 20 ms./DIV.
      Condition
      Key in ignition key cylinder


CHECK ECM (for 2AR-FE)

A247842E19

HINT:
The standard voltage between each pair of ECM terminals is shown in the table below. The appropriate conditions for checking each pair of terminals are also indicated. The result of checks should be compared with the standard voltage or resistance for that pair of terminals, displayed in the "Specified Condition" column. The illustration above can be used as a reference to identify the ECM terminal locations.


Tester Connection
Wiring Color
Terminal Description
Condition
Specified Condition
E26-16 (E1) - Body ground
BR - Body ground
Ground
Always
Below 1 Ω
A25-1 (BATT) - E26-16 (E1)
GR - BR
+B power supply
Always
11 to 14 V
A25-3 (+B2) - E26-16 (E1)
LG - BR
+B power supply
Ignition switch ON
11 to 14 V
A25-2 (+B) - E26-16 (E1)
P - BR
+B power supply
Ignition switch ON
11 to 14 V
A25-29 (IMO) - E26-16 (E1)
G - BR
Transponder key ECU assembly communication input
Ignition switch off
11 to 14 V
A25-29 (IMO) - E26-16 (E1)
G - BR
Transponder key ECU assembly communication input
Within 3 seconds after starter operates and initial combustion occurs, or within 3 seconds after ignition switch first turned to ON after battery disconnected and connected.
Pulse generation
(See waveform 1)
A25-28 (IMI) - E26-16 (E1)
Y - BR
Transponder key ECU assembly communication output
Ignition switch off
Below 1 V
A25-28 (IMI) - E26-16 (E1)
Y - BR
Transponder key ECU assembly communication output
Within 3 seconds after starter operates and initial combustion occurs, or within 3 seconds after ignition switch first turned to ON after battery disconnected and connected.
Pulse generation
(See waveform 2)


  1. Inspect using an oscilloscope.

    NOTICE:
    The waveform shown in the illustration is an example for reference only. Noise, chattering, etc. are not shown.




    1. Waveform 1 (Reference)


      B278942E01


      Text in Illustration 
      *a
      Approximately 160 ms
      *b
      Approximately 270 ms
      Tester Connection
      A25-29 (IMO) - E26-16 (E1)
      Tool Setting
      2 V/DIV., 500 ms./DIV.
      Condition
      Within 3 seconds after starter operates and initial combustion occurs, or within 3 seconds after ignition switch first turned to ON after battery disconnected and connected.



    2. Waveform 2 (Reference)


      B278943E01


      Text in Illustration 
      *a
      Approximately 160 ms
      *b
      Approximately 270 ms
      Tester Connection
      A25-28 (IMI) - E26-16 (E1)
      Tool Setting
      2 V/DIV., 500 ms./DIV.
      Condition
      Within 3 seconds after starter operates and initial combustion occurs, or within 3 seconds after ignition switch first turned to ON after battery disconnected and connected.


CHECK ECM (for 1AZ-FE)

A194498E41

HINT:
The standard voltage between each pair of ECM terminals is shown in the table below. The appropriate conditions for checking each pair of terminals are also indicated. The result of checks should be compared with the standard voltage for that pair of terminals, displayed in the "Specified Condition" column. The illustration above can be used as a reference to identify the ECM terminal locations.


Terminal No. (Symbol)
Wiring Color
Terminal Description
Condition
Specified Condition
A74-20 (BATT) - E83-104 (E1)
GR - BR
+B power supply
Always
11 to 14 V
A74-2 (+B) - E83-104 (E1)
P - BR
+B power supply
Ignition switch ON
11 to 14 V
A74-1 (+B2) - E83-104 (E1)
LG - BR
+B power supply
Ignition switch ON
11 to 14 V
E83-104 (E1) - Body ground
BR - Body ground
Ground
Always
Below 1 Ω
A74-10 (IMO) - E83-104 (E1)
G - BR
Transponder key ECU assembly communication input
Ignition switch off
11 to 14 V
A74-10 (IMO) - E83-104 (E1)
G - BR
Transponder key ECU assembly communication input
Within 3 seconds after starter operates and initial combustion occurs, or within 3 seconds after ignition switch first turned to ON after battery disconnected and connected.
Pulse generation
(See waveform 1)
A74-11 (IMI) - E83-104 (E1)
Y - BR
Transponder key ECU assembly communication output
Ignition switch off
Below 1 V
A74-11 (IMI) - E83-104 (E1)
Y - BR
Transponder key ECU assembly communication output
Within 3 seconds after starter operates and initial combustion occurs, or within 3 seconds after ignition switch first turned to ON after battery disconnected and connected.
Pulse generation
(See waveform 2)


  1. Inspect using an oscilloscope.

    NOTICE:
    The waveform shown in the illustration is an example for reference only. Noise, chattering, etc. are not shown.




    1. Waveform 1 (Reference)


      B278942E01


      Text in Illustration 
      *a
      Approximately 160 ms
      *b
      Approximately 270 ms
      Measurement Condition 
      Item
      Content
      Tester Connection
      A74-10 (IMO) - E83-104 (E1)
      Tool Setting
      2 V/DIV., 500 ms./DIV.
      Condition
      Within 3 seconds after starter operates and initial combustion occurs, or within 3 seconds after ignition switch first turned to ON after battery disconnected and connected.



    2. Waveform 2 (Reference)


      B278943E01


      Text in Illustration 
      *a
      Approximately 160 ms
      *b
      Approximately 270 ms
      Measurement Condition 
      Item
      Content
      Tester Connection
      A74-11 (IMI) - E83-104 (E1)
      Tool Setting
      2 V/DIV., 500 ms./DIV.
      Condition
      Within 3 seconds after starter operates and initial combustion occurs, or within 3 seconds after ignition switch first turned to ON after battery disconnected and connected.