Home › Vehicle Interior › THEFT DETERRENT / KEYLESS ENTRY › ENGINE IMMOBILISER SYSTEM (w/o Smart Entry and Start System)

DTC    B2784    Antenna Coil Open / Short

for Preparation Click here


DESCRIPTION

The transponder key coil is built into the transponder key amplifier and receives a key code signal from the transponder chip in the key. This signal is amplified by the amplifier, then it is output to the transponder key ECU assembly.

DTC No.
DTC Detection Condition
Trouble Area
B2784
Antenna coil is open/shorted.
  1. Wire harness or connector
  2. Transponder key amplifier
  3. Transponder key ECU assembly

WIRING DIAGRAM


B193467E08


INSPECTION PROCEDURE

NOTICE:
If the transponder key ECU assembly is replaced, refer to Service Bulletin.

1.READ VALUE USING INTELLIGENT TESTER
  1. Connect the intelligent tester to the DLC3.

  1. Turn the ignition switch to ON.

  1. Turn the intelligent tester on.

  1. Enter the following menus: Body / Immobiliser / Data List.

  1. Read the Data List according to the display on the intelligent tester.

    Immobiliser (Transponder Key ECU Assembly) 
    Tester Display
    Measurement Item/Range
    Normal Condition
    Diagnostic Note
    Antenna Coil Status
    Transponder key amplifier coil condition/Normal or Fail
    Normal: Antenna coil normal
    Fail: Antenna coil malfunctioning
    -

    OK:
    On the intelligent tester screen, "Normal" is displayed.



NG
Go to step 2
OK

REPLACE TRANSPONDER KEY ECU ASSEMBLY 

2.CHECK HARNESS AND CONNECTOR (TRANSPONDER KEY ECU - TRANSPONDER KEY AMPLIFIER)
  1. Disconnect the transponder key ECU assembly connector.

  1. Disconnect the transponder key amplifier connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    I19-4 (TXCT) - I34-5 (TXCT)
    Always
    Below 1 Ω
    I19-5 (AGND) - I34-7 (AGND)
    Always
    Below 1 Ω
    I19-14 (VC5) - I34-1 (VC5)
    Always
    Below 1 Ω
    I19-15 (CODE) - I34-4 (CODE)
    Always
    Below 1 Ω
    I19-4 (TXCT) - Body ground
    Always
    10 kΩ or higher
    I19-5 (AGND) - Body ground
    Always
    10 kΩ or higher
    I19-14 (VC5) - Body ground
    Always
    10 kΩ or higher
    I19-15 (CODE) - Body ground
    Always
    10 kΩ or higher
    I34-5 (TXCT) - Body ground
    Always
    10 kΩ or higher
    I34-7 (AGND) - Body ground
    Always
    10 kΩ or higher
    I34-1 (VC5) - Body ground
    Always
    10 kΩ or higher
    I34-4 (CODE) - Body ground
    Always
    10 kΩ or higher



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK


3.INSPECT TRANSPONDER KEY AMPLIFIER (POWER SOURCE AND BODY GROUND)
  1. Reconnect the transponder key ECU assembly connector.



    B203486E17
  1. Reconnect the transponder key amplifier connector.

  1. Measure the voltage and resistance according to the value(s) in the table below.

    Standard Voltage:
    Tester Connection
    Condition
    Specified Condition
    I19-14 (VC5) - Body ground
    No key in ignition key cylinder
    Below 1 V
    I19-14 (VC5) - Body ground
    Key in ignition key cylinder
    4.6 to 5.4 V

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    I19-5 (AGND) - Body ground
    Always
    Below 1 Ω

    Text in Illustration 
    *a
    Component with harness connected
    (Transponder Key ECU Assembly)



NG
REPLACE TRANSPONDER KEY ECU ASSEMBLY
OK

REPLACE TRANSPONDER KEY AMPLIFIER (Click here)