Home › Vehicle Interior › THEFT DETERRENT / KEYLESS ENTRY › ENGINE IMMOBILISER SYSTEM (w/ Smart Entry and Start System)

ENGINE IMMOBILISER SYSTEM (w/ Smart Entry and Start System) > DIAGNOSIS SYSTEM

for Preparation Click here



DESCRIPTION
  1. The certification ECU (smart key ECU assembly) and ECM control the vehicle engine immobiliser system functions. Engine immobiliser system data and Diagnostic Trouble Codes (DTCs) can be read through the vehicle Data Link Connector 3 (DLC3).
    In some cases, a malfunction may be occurring in the engine immobiliser system even though the security indicator light is not illuminated.
    When the system seems to be malfunctioning, use the intelligent tester to check for malfunctions and perform repairs.


CHECK DLC3
  1. Check the DLC3 (Click here).


INSPECT BATTERY VOLTAGE
  1. Measure the battery voltage.

    Standard Voltage:
    11 to 14 V

    If the voltage is below 11 V, recharge or replace the battery.


START FUNCTION PROBLEM SYMPTOMS

Symptom
Suspected Area
Component Malfunction
Possible Output DTCs
Related Data List Item
Engine cannot be started*1
Certification ECU (smart key ECU assembly)
Open or short circuit inside ECU
  1. B278A
  2. B2790
  1. Ignition Switch
  2. #Codes
  3. Immobilizer when IG=ON
  4. Immobiliser
  5. Master Key
  6. Sub Key
  7. BCC Malfunction
  8. Abnormal Status
  9. Different Encrypt Code
  10. Different Serial Number
  11. Frame Error
  12. Response
  13. Wireless Starter Com ID
  14. Wireless C Code
  15. Engine Start Condition
  16. ID-BOX Sleep Condition
  17. ID-BOX Start Condition
  18. Engine Start Request
  19. 3bit Code Request
  20. S Code Check*4
  21. L Code Check
  22. Unlock Request Receive
  23. Lock Request Receive
  24. S Code Check (Past)*4
  25. L Code Check (Past)
  26. EFI Code Receive
  27. EFI communication
Engine cannot be started*1
Certification ECU (smart key ECU assembly)*3
ID code box (immobiliser code ECU)*4
Open or short circuit inside ECU
  1. B2790
  2. B2799
  3. B279A
  1. Immobilizer when IG=ON
  2. Immobiliser
  3. Master Key
  4. Sub Key
  5. BCC Malfunction
  6. Abnormal Status
  7. Different Encrypt Code
  8. Different Serial Number
  9. Frame Error
  10. Response
  11. ID-BOX Sleep Condition
  12. ID-BOX Start Condition
  13. Engine Start Request
  14. 3bit Code Request
  15. S Code Check*4
  16. L Code Check
  17. S Code Check (Past)*4
  18. L Code Check (Past)
  19. EFI Code Receive
  20. EFI communication
ECM
Open or short circuit inside ECU
  1. B2799
  2. B279A
  3. B279C
EFI Code Receive
SFI system
ECM incompatible with installed engine immobiliser system
B279C
  1. Engine Start Condition
  2. EFI Code Receive
Blocking system*5
Open or short circuit inside ECU
  1. B2799
  2. B279A
  3. B1586
  4. B1587
-
Power source mode cannot be changed*1
Engine switch
Open or short circuit inside switch
B278A
  1. Ignition Switch
  2. Unlock Request Receive
  3. Lock Request Receive
Certification ECU (smart key ECU assembly)
Open or short circuit inside ECU
  1. B2271
  2. B2274
  1. Ignition Switch
  2. Immobilizer when IG=ON
  3. Immobiliser
Steering lock lock/unlock not possible*2
Steering lock ECU (steering lock actuator assembly)
  1. Open or short circuit inside ECU
  2. Actuator stuck
  1. B2781
  2. B2782
  3. B2788
  1. Unlock Request Receive
  2. Lock Request Receive
  1. *1: Refer to Problem Symptoms Table for Smart Entry and Start System (for Start Function).
  2. *2: Refer to Problem Symptoms Table for Steering Lock System.
  3. *3: w/ Wireless Door Lock Buzzer Answer Back Function
  4. *4: w/o Wireless Door Lock Buzzer Answer Back Function
  5. *5: w/ Blocking System