Home › Vehicle Interior › THEFT DETERRENT / KEYLESS ENTRY › ENGINE IMMOBILISER SYSTEM (w/o Smart Entry and Start System)

ENGINE IMMOBILISER SYSTEM (w/o Smart Entry and Start System) > DATA LIST / ACTIVE TEST

for Preparation Click here



DATA LIST

HINT:
Using the intelligent tester to read the Data List allows the values or states of switches, sensors, actuators and other items to be read without removing any parts. This non-intrusive inspection can be very useful because intermittent conditions or signals may be discovered before parts or wiring is disturbed. Reading the Data List information early in troubleshooting is one way to save diagnostic time.

NOTICE:
In the table below, the values listed under "Normal Condition" are reference values. Do not depend solely on these reference values when deciding whether a part is faulty or not.

  1. Connect the intelligent tester to the DLC3.

  2. Turn the ignition switch to ON.

  3. Turn the intelligent tester on.

  4. Enter the following menus: Body / Immobiliser / Data List.

  5. Read the Data List according to the display on the intelligent tester.

    Immobiliser (Transponder Key ECU Assembly) 
    Tester Display
    Measurement Item/Range
    Normal Condition
    Diagnostic Note
    Key SW
    Unlock warning switch signal/ON or OFF
    ON: Key in ignition key cylinder
    OFF: No key in ignition key cylinder
    -
    IG SW
    Ignition switch signal/ON or OFF
    ON: Ignition switch ON or engine start
    OFF: Ignition switch ACC or off
    -
    Immobiliser
    Immobiliser system status/Set or Unset
    Set: No key in ignition key cylinder, or 20 sec. elapsed after turning the ignition switch to on (ACC) or off
    Unset: Key in ignition key cylinder
    -
    Response
    Transponder chip data/NG or OK
    NG: Data error
    OK: Data OK
    -
    Frame Error
    Transponder chip data/NG or OK
    NG: Data error
    OK: Data OK
    -
    Different Serial Number
    Transponder chip data/NG or OK
    NG: Data error
    OK: Data OK
    -
    Different Encrypt Code
    Transponder chip data/NG or OK
    NG: Data error
    OK: Data OK
    -
    Abnormal Status
    Transponder chip data/NG or OK
    NG: Data error
    OK: Data OK
    -
    Bcc Malfunction
    Transponder chip data/NG or OK
    NG: Incorrect data being sent
    OK: Correct data being sent
    -
    Sub Key
    Sub key code signal/Reg or Unreg
    Reg: Registered sub key code sent
    Unreg: Unmatching sub key code sent
    -
    Master Key
    Master key code signal/Reg or Unreg
    Reg: Registered master key code sent
    Unreg: Unmatching master key code sent
    -
    Transponder S-Code
    Number of registered sub key/min. 0, max. 15
    Number of registered sub key
    -
    Transponder M-Code
    Number of registered master key/min. 0, max. 15
    Number of registered master key
    -
    +B
    Power source/Break or Normal
    Break: Power source open
    Normal: Power source normal
    -
    Antenna Coil Status
    Transponder key amplifier coil condition/Normal or Fail
    Normal: Antenna coil normal
    Fail: Antenna coil malfunctioning
    -
    E/G Start Permission
    Engine start permission/OK or NG
    OK: Engine start permitted
    NG: Engine start not permitted
    -
    Immobi ECU Comm Spd
    Immobiliser ECU communication speed/Unknown, 50bps, 200bps or No Res
    Unknown: ECU communication speed unknown
    50bps: ECU communication speed 50 bps
    200bps: ECU communication speed 200 bps
    No Res: ECU communication speed no response
    -
    The Number of DTCs
    Number of DTCs / Min.: 0, Max.: 255
    Number of stored DTCs
    -


ACTIVE TEST

HINT:
Using the intelligent tester to perform Active Tests allows relays, VSVs, actuators and other items to be operated without removing any parts. This non-intrusive functional inspection can be very useful because intermittent operation may be discovered before parts or wiring is disturbed. Performing Active Tests early in troubleshooting is one way to save diagnostic time. Data List information can be displayed while performing Active Tests.

  1. Connect the intelligent tester to the DLC3.

  2. Turn the ignition switch to ON.

  3. Turn the intelligent tester on.

  4. Enter the following menus: Body / Immobiliser or Main Body / Active Test.

  5. Perform the Active Test according to the display on the intelligent tester.

    Immobiliser (Transponder Key ECU Assembly) 
    Tester Display
    Test Part
    Control Range
    Diagnostic Note
    Security Indicator
    Security Indicator Light
    ON/OFF
    -

    Main Body (Main Body ECU (Multiplex Network Body ECU)) 
    Tester Display
    Test Part
    Control Range
    Diagnostic Note
    Security Indicator
    Security indicator light
    OFF/ON
    -