FRONT DRIVE SHAFT ASSEMBLY (for 2AR-FE) > DISASSEMBLY |
| 1. REMOVE FRONT NO. 2 AXLE INBOARD JOINT BOOT CLAMP (for TMC Made) |
for One Touch Type:
![]() |
Using a screwdriver, remove the front No. 2 axle inboard joint boot clamp.
| *A | for One Touch Type |
| *B | for Claw Engagement Type |
for Claw Engagement Type:
Using needle-nose pliers, remove the front No. 2 axle inboard joint boot clamp.
| *a | claws |
| 2. REMOVE FRONT NO. 2 AXLE INBOARD JOINT BOOT CLAMP (except TMC Made) |
![]() |
Using needle-nose pliers, remove the front No. 2 axle inboard joint boot clamp.
| 3. REMOVE FRONT AXLE INBOARD JOINT BOOT CLAMP (for TMC Made) |
| 4. REMOVE FRONT AXLE INBOARD JOINT BOOT CLAMP (except TMC Made) |
| 5. SEPARATE FRONT AXLE INBOARD JOINT BOOT |
Separate the front axle inboard joint boot from the front drive inboard joint assembly.
| 6. REMOVE FRONT DRIVE INBOARD JOINT ASSEMBLY (for TMC Made) |
Remove the old grease from the front drive inboard joint assembly.
![]() |
Put matchmarks on the front drive inboard joint assembly and front drive outboard joint shaft assembly.
| *a | Matchmark |
Remove the front drive inboard joint assembly from the front drive outboard joint shaft assembly.
Hold the drive shaft in a vise between aluminum plates.
![]() |
Using a snap ring expander, remove the shaft snap ring from the front drive outboard joint shaft assembly.
![]() |
Put matchmarks on the front drive outboard joint shaft assembly and tripod joint.
| *a | Matchmark |
Using a brass bar and a hammer, tap out the tripod joint from the front drive outboard joint shaft assembly.
| 7. REMOVE FRONT DRIVE INBOARD JOINT ASSEMBLY (except TMC Made) |
Remove the old grease from the front drive inboard joint assembly.
![]() |
Put matchmarks on the front drive inboard joint assembly and front drive outboard joint shaft assembly.
| *a | Matchmark |
Remove the front drive inboard joint assembly from the front drive outboard joint shaft assembly.
Hold the drive shaft in a vise between aluminum plates.
![]() |
Using a snap ring expander, remove the shaft snap ring from the front drive outboard joint shaft assembly.
![]() |
Put matchmarks on the front drive outboard joint shaft assembly and tripod joint.
| *a | Matchmark |
Using a brass bar and a hammer, tap out the tripod joint from the front drive outboard joint shaft assembly.
| 8. REMOVE FRONT AXLE INBOARD JOINT BOOT |
Remove the front No. 2 axle inboard joint boot clamp, front axle inboard joint boot and front axle inboard joint boot clamp.
| 9. REMOVE FRONT DRIVE SHAFT DAMPER (for TMC Made) |
for One Touch Type:
![]() |
Using a screwdriver, remove the front drive shaft damper clamp.
| *A | for One Touch Type |
| *B | for Claw Engagement Type |
for Claw Engagement Type:
Using needle-nose pliers, remove the front drive shaft damper clamp.
| *a | claws |
Remove the front drive shaft damper.
| 10. REMOVE FRONT DRIVE SHAFT DAMPER (except TMC Made) |
![]() |
Using needle-nose pliers, remove the front drive shaft damper clamp.
Remove the front drive shaft damper.
| 11. REMOVE FRONT NO. 2 AXLE OUTBOARD JOINT BOOT CLAMP (for TMC Made) |
![]() |
Using a screwdriver, remove the front No. 2 axle outboard joint boot clamp.
| 12. REMOVE FRONT NO. 2 AXLE OUTBOARD JOINT BOOT CLAMP (except TMC Made) |
![]() |
Using pliers, remove the front No. 2 axle outboard joint boot clamp.
| 13. REMOVE FRONT AXLE OUTBOARD JOINT BOOT CLAMP (for TMC Made) |
| 14. REMOVE FRONT AXLE OUTBOARD JOINT BOOT CLAMP (except TMC Made) |
| 15. REMOVE FRONT AXLE OUTBOARD JOINT BOOT |
Remove the front axle outboard joint boot clamp, front axle outboard joint boot and front No. 2 axle outboard joint boot clamp from the front drive outboard joint shaft assembly.
Remove the grease from the outboard joint.
| 16. REMOVE FRONT DRIVE SHAFT DUST COVER LH |
![]() |
Using SST and a press, remove the front drive shaft dust cover LH.
| 17. REMOVE FRONT DRIVE SHAFT DUST COVER RH |
![]() |
Using a press, remove the front drive shaft dust cover RH.
| 18. REMOVE FRONT DRIVE SHAFT DUST COVER (for RH Side) |
![]() |
Using SST and a press, remove the front drive shaft dust cover.
| 19. REMOVE FRONT DRIVE SHAFT BEARING (for RH Side) |
![]() |
Using a snap ring expander, remove the drive shaft hole snap ring.
![]() |
Using SST and a press, remove the front drive shaft bearing.